Template:Networking rut2xx upnp: Difference between revisions
Template:Networking rut2xx upnp (view source)
Revision as of 15:40, 7 February 2020
, 7 February 2020no edit summary
No edit summary |
No edit summary |
||
| Line 10: | Line 10: | ||
[[File:{{{file_redirects}}}|border|class=tlt-border]] | [[File:{{{file_redirects}}}|border|class=tlt-border]] | ||
==General Settings== | ==General Settings== | ||
| Line 25: | Line 23: | ||
<tr> | <tr> | ||
<td>Enabled</td> | <td>Enabled</td> | ||
<td></td> | <td>yes | no; default: '''no'''</td> | ||
<td></td> | <td>Turns the UPNP service on or off.</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Enable secure mode</td> | <td>Enable secure mode</td> | ||
<td></td> | <td>yes | no; default: '''yes'''</td> | ||
<td></td> | <td>Allow adding forwards only to requesting IP addresses</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Enable additional logging</td> | <td>Enable additional logging</td> | ||
<td></td> | <td>yes | no; default: '''no'''</td> | ||
<td></td> | <td>Puts extra debugging information into the system log</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Downlink</td> | <td>Downlink</td> | ||
<td></td> | <td>Default: '''1024'''</td> | ||
<td></td> | <td>Value in KByte/s, informational only</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Uplink</td> | <td>Uplink</td> | ||
<td></td> | <td>Default: '''512'''</td> | ||
<td></td> | <td>Value in KByte/s, informational only</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Port</td> | <td>Port</td> | ||
<td></td> | <td>Default: '''5000'''</td> | ||
<td></td> | <td>Port to listen for requests</td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| Line 67: | Line 65: | ||
<tr> | <tr> | ||
<td>Report system instead of daemon uptime</td> | <td>Report system instead of daemon uptime</td> | ||
<td></td> | <td>yes | no; default: '''no'''</td> | ||
<td></td> | <td></td> | ||
</tr> | </tr> | ||
| Line 131: | Line 129: | ||
<tr> | <tr> | ||
<td>External ports</td> | <td>External ports</td> | ||
<td> | <td>Default: '''1024-65535'''</td> | ||
<td>External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td> | <td>External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Internal Addresses</td> | <td>Internal Addresses</td> | ||
<td> | <td>Default: '''0.0.0.0/0'''</td> | ||
<td>Internal address to be redirect to</td> | <td>Internal address to be redirect to</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Internal ports</td> | <td>Internal ports</td> | ||
<td> | <td>Default: '''1024-65535'''</td> | ||
<td>Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td> | <td>Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Action</td> | <td>Action</td> | ||
<td> | <td>Default: '''allow'''</td> | ||
<td>Allows or forbids the UPnP service to open the specified port</td> | <td>Allows or forbids the UPnP service to open the specified port</td> | ||
</tr> | </tr> | ||
</table> | </table> | ||