1,663
edits
Changes
→Teltonika configurator
If you do not have preset you can download them from below table:
If you do not have preset you can download them from below table:
<br>
{|
{|
|[[File:Eye Sensors.png|alt=]]
|[[File:Eye Sensors.png|frameless]]
|
|
[[File:IBeacon and EYE Sensors.png|frameless]]
[[File:IBeacon and EYE Sensors.png|alt=]]
|
|
[[File:Eddystone and EYE Sensors.png|frameless]]
[[File:Eddystone and EYE Sensors.png]]
|-
|-
|Preset you should use:
|Preset you should use:
|EYE Sensors
|EYE Sensors
|EYE iBeacon
| EYE iBeacon
|EYE Eddystone
|EYE Eddystone
|-
|-
| colspan="4" |Instructions how you can manually add a preset: [[How_to_add_a_BLE_preset_to_the_configurator|link]]
| colspan="4" |Instructions how you can manually add a preset: [[How_to_add_a_BLE_preset_to_the_configurator|link]]
|}
|}
<br>
<br>
<br>
'''Note''': To receive data need to enable corresponding IO elements in I/O tab.
'''Note''': To receive data need to enable corresponding IO elements in I/O tab.
===Teltonika configurator new functionalities (not released yet)===
===Teltonika configurator new functionalities (not released yet)===
Functionalities were reorganized and transferred to Bluetooth 4.0 configuration tab with additional horizontal tabs selection for specific settings:
Functionalities were reorganized and transferred to Bluetooth 4.0 configuration tab with additional horizontal tabs selection for specific settings:
<br>
<br>
* '''Global''' - Parameters responsible for device scanning ability like power and duratations.
*'''Global''' - Parameters responsible for device scanning ability like power and duratations.
* '''EYE''' - Parameters to configure data reading from EYE sensors.
*'''EYE''' - Parameters to configure data reading from EYE sensors.
<br>
<br>
'''Common settings'''
'''Common settings'''
<br>
<br>
* '''Non Stop Scan''' - Enable Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
*'''Non Stop Scan''' - Enable Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
* '''Sensors and Beacons Update frequency''' - changes sensors temperature/humidity/battery voltage data update frequency. Minimum value: 30s, maximum value: 65535s. Recommended value 30.
*'''Sensors and Beacons Update frequency''' - changes sensors temperature/humidity/battery voltage data update frequency. Minimum value: 30s, maximum value: 65535s. Recommended value 30.
* '''BLE Scan Duration''' - Sensors data reading time. Recommended value 30.
*'''BLE Scan Duration''' - Sensors data reading time. Recommended value 30.
* '''Scan retries until error''' - Scan retries count, till start to show the value as Error '3000' - sensor disconnected. Recommended value 30.
*'''Scan retries until error''' - Scan retries count, till start to show the value as Error '3000' - sensor disconnected. Recommended value 30.
* '''BT Power Level''' - Telematics device Bluetooth power level setting.
*'''BT Power Level''' - Telematics device Bluetooth power level setting.
* '''BLE Broadcasting service ID''' - Telematics device can broadcast configured ID.
*'''BLE Broadcasting service ID''' - Telematics device can broadcast configured ID.
* ''' BLE connection control''' - Connection mode settings. If broadcasting ID is configured, parameter should be set to Prohibit.
*''' BLE connection control''' - Connection mode settings. If broadcasting ID is configured, parameter should be set to Prohibit.
<br>
<br>
Table below describes I/O elements which were added for EYE sensor and proximity functionalities.
Table below describes I/O elements which were added for EYE sensor and proximity functionalities.
<table class="nd-othertables_2" style="width: 100%;">
<br><table class="nd-othertables_2" style="width: 100%;">
<tr>
<tr>
<th style="width: 10%; text-align:center; vertical-align:middle;">Property ID in AVL packet</th>
<th style="width: 10%; text-align:center; vertical-align:middle;">Property ID in AVL packet</th>
<td style="width: 25%; text-align:center; vertical-align:middle;">List of Beacon which were lost from proximity zones</td>
<td style="width: 25%; text-align:center; vertical-align:middle;">List of Beacon which were lost from proximity zones</td>
</tr>
</tr>
</table>
</table>
==<p style="font-size:32px><span style="color:#0054A6">EYE Sensor Protocol overwiev</span></p>==
==<p style="font-size:32px"><span style="color:#0054A6">EYE Sensor Protocol overwiev</span></p>==
===Sensor advertising ===
===Sensor advertising===
<br>
<br>
[[File:Sensors data.png|center]]
[[File:Sensors data.png|center]]
|+'''Table 1. Flag Encoded Date'''
|+'''Table 1. Flag Encoded Date'''
|-
|-
! Data!!Size (Bytes)!!Description
!Data!! Size (Bytes)!!Description
|-
|-
|Flags||1||Each set bit (0-7) means the presence of value (0-7). Bits:
|Flags||1||Each set bit (0-7) means the presence of value (0-7). Bits:
<br>7 – Battery voltage value presence
<br>7 – Battery voltage value presence
|-
|-
| Value 0||2 ||Temperature
|Value 0||2||Temperature
<br>Value in Celsius * 100
<br>Value in Celsius * 100
<br>NOTE: present only if bit 0 is set, otherwise is not being sent
<br>NOTE: present only if bit 0 is set, otherwise is not being sent
|-
|-
|Value 1||1||Humidity
|Value 1 ||1||Humidity
<br>Value in percent
<br>Value in percent
<br>NOTE: present only if bit 1 is set, otherwise is not being sent
<br>NOTE: present only if bit 1 is set, otherwise is not being sent
|-
|-
| Value 2||2||Movement Sensor counter
|Value 2||2||Movement Sensor counter
<br>Most significant bit indicates movement state and 15 least significant bits represent count of movement events.
<br>Most significant bit indicates movement state and 15 least significant bits represent count of movement events.
<br>NOTE: present only if bit 4 is set, otherwise is not being sent
<br>NOTE: present only if bit 4 is set, otherwise is not being sent
|-
|-
|Value 3||3||Movement sensor angle
|Value 3 ||3||Movement sensor angle
<br>Most significant byte – pitch (-90/+90)
<br>Most significant byte – pitch (-90/+90)
<br>Two least significant bytes – roll (-180/+180)
<br>Two least significant bytes – roll (-180/+180)
<br>NOTE: present only if bit 5 is set, otherwise is not being sent
<br>NOTE: present only if bit 5 is set, otherwise is not being sent
|-
|-
| Value 4|| 1||Battery Voltage
|Value 4||1|| Battery Voltage
<br>Battery voltage in mV = 2000 + VALUE * 10
<br>Battery voltage in mV = 2000 + VALUE * 10
<br>NOTE: present only if bit 7 is set, otherwise is not being sent
<br>NOTE: present only if bit 7 is set, otherwise is not being sent
| colspan="2" |'''1 byte types'''
| colspan="2" |'''1 byte types'''
|-
|-
|0 ||For future use
|0||For future use
|-
|-
|... ||For future use
|...||For future use
|-
|-
|49||For future use
|49||For future use
| colspan="2" |'''8 bytes types'''
| colspan="2" |'''8 bytes types'''
|-
|-
|150 ||For future use
|150||For future use
|-
|-
|...||For future use
|...||For future use
|-
|-
|199 ||For future use
| 199|| For future use
|-
|-
| colspan="2" |'''Variable size types'''
| colspan="2" |'''Variable size types'''
|...||For future use
|...||For future use
|-
|-
|255||For future use
|255 ||For future use
|-
|-
|}
|}
| style="vertical-align: middle; text-align: center;" |<span style="background:#03C03C">0C</span>
| style="vertical-align: middle; text-align: center;" |<span style="background:#03C03C">0C</span>
|-
|-
| style="vertical-align: middle; text-align: center;" | Type
| style="vertical-align: middle; text-align: center;" |Type
| style="vertical-align: middle; text-align: center;" |<span style="background:#FF3800">09</span>
| style="vertical-align: middle; text-align: center;" |<span style="background:#FF3800">09</span>
|-
|-
| style="vertical-align: middle; text-align: center;" |Temperature
| style="vertical-align: middle; text-align: center;" |Temperature
| style="vertical-align: middle; text-align: center;" |<span style="background:#00FF00">08B4</span>
| style="vertical-align: middle; text-align: center;" |<span style="background:#00FF00">08B4</span>
|Raw value example 0x08B4 hex, 2228 dec.
| Raw value example 0x08B4 hex, 2228 dec.
Raw value needs to be divided by 100.
Raw value needs to be divided by 100.
'''Real temperature''' is 22,28 Celsius.
'''Real temperature''' is 22,28 Celsius.
|-
|-
| style="vertical-align: middle; text-align: center;" |Humidity
| style="vertical-align: middle; text-align: center;" | Humidity
| style="vertical-align: middle; text-align: center;" |<span style="background:#007FFF">12</span>
| style="vertical-align: middle; text-align: center;" |<span style="background:#007FFF">12</span>
| Raw value example 0x12 hex, 18 dec.
|Raw value example 0x12 hex, 18 dec.
Decimal value is humidity in percent. Humidity 18 %
Decimal value is humidity in percent. Humidity 18 %
|-
|-
| style="vertical-align: middle; text-align: center;" |Movement
| style="vertical-align: middle; text-align: center;" |Movement
| style="vertical-align: middle; text-align: center;" |<span style="background:#F4C2C2">0CCB</span>
| style="vertical-align: middle; text-align: center;" |<span style="background:#F4C2C2">0CCB</span>
|(MSB)0000 1100 1100 1011(LSB) binary
| (MSB)0000 1100 1100 1011(LSB) binary
0 - Most significant byte(MSB) represents '''Movement status'''. In this case device is not moving 0. If it was 1 device is moving.
0 - Most significant byte(MSB) represents '''Movement status'''. In this case device is not moving 0. If it was 1 device is moving.
