Changes

Template:Beacons List (view source)

Revision as of 16:43, 27 December 2021

1,681 bytes removed ,  16:43, 27 December 2021
→‎EYE Sensor Capturing Configuration
Line 78: Line 78:  
* '''Additional Data Offset''' and '''Additional Data Size''' - allows to capture specific data of the Beacons advertised packet e.g. battery voltage or status. These additional parameters depend on Beacon type and advertisement packet. In order to capture full packet of the Beacon - Offset can be left at 0 and Size matched by actual length of the advertised packet.
 
* '''Additional Data Offset''' and '''Additional Data Size''' - allows to capture specific data of the Beacons advertised packet e.g. battery voltage or status. These additional parameters depend on Beacon type and advertisement packet. In order to capture full packet of the Beacon - Offset can be left at 0 and Size matched by actual length of the advertised packet.
 
* '''Beacon ID Source'''- Beacon ID source can be selected. When Beacon ID is used, source is used as configured in Beacon ID offset and Beacon ID size columns. When Beacon MAC address is selected, Beacon ID will be replaced with MAC address. IO structure remains the same, but Beacon ID size will always be reported as 0x06.
 
* '''Beacon ID Source'''- Beacon ID source can be selected. When Beacon ID is used, source is used as configured in Beacon ID offset and Beacon ID size columns. When Beacon MAC address is selected, Beacon ID will be replaced with MAC address. IO structure remains the same, but Beacon ID size will always be reported as 0x06.
−
  −
==== EYE Sensor Capturing Configuration ====
  −
As an example on how to set Beacons Capturing Configuration parameters EYE Sensor can be used. Protocols used can be found [[EYE SENSOR / BTSMP1|here]].
  −
[[File:Beacons Capturing Configuration set.png|thumb|1143x1143px|Parameter values]]
  −
[[File:Beacon temp marked.png|right|frameless|545x545px]]
  −
Information shown after setting the parameters. Red rectangle indicates configured EYE sensors.
  −
[[File:Eddystone temperature.png|left|frameless|552x552px|Eddystone temperature]]
  −
<br></br>
  −
<br></br>
  −
<br></br>
  −
<br></br>
  −
<br></br>
  −
  −
  −
  −
  −
  −
* '''Name''' -  Eddystone and iBeacon were typed to name different sensors.
  −
*'''Manufacturer ID''' - is taken from protocol description, passing 9bytes and capturing UUID and Type. AAFE00, to comply Manufacturer ID size which is 4 bytes, 00 is added.
  −
*'''Manufacturer ID Offset''' - number used to indicate when Manufacturer ID starts in advertising packet.
  −
*'''Manufacturer ID Size''' - number which indicates length of Manufacturer ID.
  −
*'''Beacon ID Offset''' - number used to indicate when Beacon ID starts in advertising packet.
  −
*'''Beacon ID Size''' - number which indicates length of Beacon ID size, Instance ID is set in Eddystone and whole ID in iBeacon.
  −
*'''Additional Data Offset''' and '''Additional Data Size''' - allows to capture specific data of the Beacons advertised packet e.g. Temperature.
  −
*'''Beacon ID Source'''- configured ID output is shown in pictures. MAC address can be used as Source ID as well, in this case, It would be showed in ID section.
  −
  −
'''Note''': Due to differencies in iBeacon and Eddystone advertising packets, number of Additional Data offset is different as well.
      
==== EYE Sensor Capturing Configuration ====
 
==== EYE Sensor Capturing Configuration ====
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/69701"

Navigation menu