0
edits
Changes
no edit summary
__TOC__
__TOC__
== Product Specification ==
<br>
<table class="nd-othertables" style="width: 68%;">
<th style="width: 10%; text-align:left; vertical-align:middle; color:black">Technical data</th>
<th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
</tr>
<tr>
<td style="width: 8%; text-align:left;">Supported by</td>
<td style="width: 8%; text-align:left">FMB640, FMC640, FMB125, FMC125, FMB225, FMC225</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">Camera Resolution</td>
<td style="width: 8%; text-align:left">1280 x 720 (HD)</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">View angle</td>
<td style="width: 8%; text-align:left">30 (V), 52 (H), 60 (D)</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">Size</td>
<td style="width: 8%; text-align:left">80 x 120 x 50 mm</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">SD card</td>
<td style="width: 8%; text-align:left">Max. 64GB</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">Video encoding</td>
<td style="width: 8%; text-align:left">H264</td>
</tr>
<tr>
<table class="nd-othertables" style="width: 68%;">
<th style="width: 10%; text-align:left; vertical-align:middle; color:black">Electrical parameters</th>
<th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
</tr>
<tr>
<td style="width: 8%; text-align:left;">Input voltage range</td>
<td style="width: 8%; text-align:left">9 – 36 V</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">Temperature</td>
<td style="width: 8%; text-align:left">-20 °C to +70 °C (operation)
-40 °C to +85 °C (storage)</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">Relative Humidity</td>
<td style="width: 8%; text-align:left">Max. 90 %</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">Power consumption</td>
<td style="width: 8%; text-align:left">12V max @300mA
12V Idle state @ 3mA</td>
</tr>
<tr><br>
<table class="nd-othertables" style="width: 68%;">
<th style="width: 10%; text-align:left; vertical-align:middle; color:black">Interface</th>
<th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
</tr>
<tr>
<td style="width: 8%; text-align:left;">USB</td>
<td style="width: 8%; text-align:left">USB 2.0 (for calibration)</td>
</tr>
<tr>
<td style="width: 8%; text-align:left">CAN</td>
<td style="width: 8%; text-align:left">CAN 2.0 (Car signal – Left/Right, Speed, RPM, Brake)</td>
</tr>
<tr><br>
<td style="width: 8%; text-align:left">RS232</td>
<td style="width: 8%; text-align:left">Indicator TX/RC (for communication with FM device)</td>
</tr>
</table>
== Main (front) camera unit preparation ==
== Main (front) camera unit preparation ==
[[File:Vehinst14.jpg|center|frameless|363x363px]]
[[File:Vehinst14.jpg|center|frameless|363x363px]]
== Product Specification ==
===Camera location and Vehicle Measurement===
Camera location and vehicle measurement can affect ADAS performance. It`s very important put accurate data for the best performance.
[[File:Vehinst15.png|center|frameless|404x404px|alt=]]
<table class="nd-othertables" style="width: 68%;">
<table class="nd-othertables" style="width: 68%;">
<th style="width: 10%; text-align:left; vertical-align:middle; color:black">Camera Option</th>
<th style="width: 10%; text-align:left; vertical-align:middle; color:black">Interface</th>
<th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
<th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
</tr>
</tr>
<tr>
<tr>
<td style="width: 8%; text-align:left;">USB</td>
<td style="width: 8%; text-align:left;">Camera Height</td>
<td style="width: 8%; text-align:left">USB 2.0 (for calibration)</td>
<td style="width: 8%; text-align:left">Distance from ground to the center of camera lens.</td>
</tr>
</tr>
<tr>
<tr>
<td style="width: 8%; text-align:left">CAN</td>
<td style="width: 8%; text-align:left">Camera Center</td>
<td style="width: 8%; text-align:left">CAN 2.0 (Car signal – Left/Right, Speed, RPM, Brake)</td>
<td style="width: 8%; text-align:left">Distance from the center of windshield to camera lens
“-“: Left Side / “+”:Right Side
(If ADAS is attached 5cm to the right from the center, input 5.
If ADAS is attached 5cm to the left from the center, input -5.)
</td>
</tr>
</tr>
<tr><br>
<tr>
<td style="width: 8%; text-align:left">RS232</td>
<td style="width: 8%; text-align:left">Camera to Wheel</td>
<td style="width: 8%; text-align:left">Indicator TX/RC (for communication with FM device)</td>
<td style="width: 8%; text-align:left">Distance from the camera to the center of the wheel.
</tr>
'''For trucks or buses''', some vehicles’ wheels are located behind.
</table>
In this case, please input 20cm.
</td>
</tr><tr><td>Vehicle Width</td><td>Distance between the wheels.
Measure distance from left outside boarder to right outside boarder of the wheels.
</td></tr><tr><td>Camera to bumper</td><td>Distance from the camera lens to the end of the bumper.
For trucks or buses, it is recommended to input 300 if sensitive FCW warning is needed.
</td></tr></table>
Camera angle – adjust the camera angle to locate the horizontal between the red guide lines.
[[File:Vehinst16.png|center|frameless|316x316px]]
In case of indoor installation or somewhere you cannot see the horizon properly, use same data to "'''Camera Height'''”. Mark the same height on the wall apart about 3 ~ 5 meters from the vehicle.
[[File:Vehinst17.png|center|frameless|332x332px]]
Fine Camera Angle - For better accuracy of ADAS, locate the yellow dotted line in the horizon as close as possible.
[[File:Vehinst18.png|center|frameless|344x344px]]
Hood Line - Locate the red line at the end of the vehicle’s hood line to remove the useless area.
[[File:Vehinst19.png|center|frameless|360x360px]]
Please follow link for video instruction: https://www.youtube.com/watch?v=93wrc6j9aqA
==ADAS configuration==
{| class="wikitable"
| colspan="2" |'''You can adjust the LDW Sensitivity for your convenience'''
|-
|
* Enable LDW function. (On / Off)
* Set the Activation Speed (15, 30, 45, 60, 75km/h).
* Set the sensitivity of LDW warning on a scale of 1 to 5.
* As the level gets higher, it gets more sensitive.
* Enable Repeat LDW (On / Off)
* If it’s on, ADAS keeps warning until the driver secures the lane.
* Warning sound: Select preferred warning sound for LDW.
|[[File:Mdconfi1.png|center|frameless]]
|-
| colspan="2" |'''You can adjust the FCW Sensitivity for your convenience:'''
|-
|
* Enable FCW function. (On / Off)
* Set the sensitivity of FCW warning on a scale of 1 to 5.
(As the level gets higher, it gets more sensitive)
* Enable Repeat FCW (On / Off).
(If it’s on, ADAS keeps warning until the driver secures safe distance)
* Enable Sync with Brake (On / Off).
(If it’s on, ADAS won’t give FCW warning if the brake pedal was used)
* Warning sound: Select preferred warning sound for FCW
|[[File:Mdconf2.png|center|frameless|301x301px]]
|-
| colspan="2" |'''Safety distance alert setup:'''
|-
|
* Enable SDA function. (On / Off)
* Set the sensitivity of SDA on a scale of 1 to 5.
* As the level gets higher, it gets more sensitive.
* Repeat SDA and SDA re-alert can be changed. (On / Off)
- Repeat SDA: If it’s on, ADAS keeps warning until the driver secures safe distance.
''- Re-alert SDA: If it’s on, ADAS gives warnings every time''
''the same front vehicle gets closer than safe distance.''
|[[File:Mdconfi3.png|center|frameless]]
|-
| colspan="2" |'''Pedestrian collision warning setup:'''
|-
|
* Enable PCW function. (On / Off)
* Warning sound: Select preferred warning sound for PCW.
|[[File:Mdconfi4.png|center|frameless]]
|-
| colspan="2" |'''Advanced ADAS setup:'''
|-
|
* Enable Forward Proximity Warning function. (On / Off)
* Set the warning range on a scale of 1 to 3.
(As the level gets higher, it gets more sensitive)
* Enable Front vehicle start alarm. (On / Off)
* Enable Speed Limit Recognition. (On / Off)
* Set the warning sensitivity (0, 5, 10, 15, 20%).
Ex) If you set 10% then you will get alarm
when your speed over the limit more than 10%,
100km limit -> Warning start from 110km speed.
* Enable voice guidance (On / Off).
|[[File:Mdconfi5.1.png|center|frameless]]
|-
| colspan="2" |'''Fleet management setup'''
|-
|
* Set Speed limit warning (Off, 80, 90, 100, 110, 120, 130, 140km/h).
- You can set your own speed limit for your fleet.
- You can set speed limit of your vehicle and get warning if you over the speed limit.
* Enable Transmit data RS-232 feature
(Converter mode should be selected to work with FMx125).
It allows ADAS event data transmission to integrated device.
* Set Lock volume button control on a scale of 1 to 5 and Off.
You can fix the volume level and prevent the driver from adjusting the
settings using indicator.
* Set Break time alarm on a scale of 1 to 6 hours and Off.
* Enable Vibration setting for LDW, FCW, PCW (On / Off / Both).
You can check the connection with the button.
|[[File:Mdconfi6.1.png|center|frameless]]
|-
| colspan="2" |'''Miscellaneous Settings:'''
|-
|
* Speed Unit on Analog video output (km/h or MPH).
* Set Video out format (NTSC / PAL).
* Set Voice guide language
(English / Korean / Chinese / Spanish / Japanese / Hebrew/ No Sound).
* Enable Indicator buzzer (On / Off).
* Speed Display on Indicator could be ON/Off
|[[File:Mdconfi7.png|center|frameless]]
|-
| colspan="2" |'''ADAS Setup Complete'''
|-
|
* Click “Complete” button to finish Calibration setup. Then ADAS will be
rebooted automatically.
* Click “Export vehicle profile” button, if you want to download vehicleprofile.dat.
This vehicleprofile contains all the calibration settings you’ve set.
With this file, you can simply apply current settings to another vehicle.
|[[File:Mdconfi8.png|frameless|alt=|center|351x351px]]
|}
