2,544
edits
Changes
mLine 1:
Line 1: − + Line 5:
Line 5: − + − + − + Line 19:
Line 19: − − Line 28:
Line 26: − + − +
no edit summary
The software of CAN adapters - [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] can now be updated Over The Air by using [[FOTA WEB]] and one of the FMB1YX devices. Upgrading the software of CAN adapter will add more program numbers, thus, more vehicle models will be supported.
The software of CAN adapters - [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] can now be updated Over The Air by using [[FOTA WEB]] and one of the FMx1YX devices. Upgrading the software of the CAN adapter will add more program numbers, thus, more vehicle models will be supported.
<b>Please note</b>, that only the newer version of LV-CAN200 and ALL-CAN300 CAN adapters support this feature. The version of the CAN adapter can be checked by sending an SMS command [[FMB_lvcangetinfo|lvcangetinfo]]. If, in the response message, <b>"SWRev:"</b> is <b>145</b>, the CAN adapter is older and if it is <b>245</b>, the adapter is newer. It does not apply to CAN-CONTROL - all CAN-CONTROL adapters support firmware updates over the air.
<b>Please note</b>, that only the newer version of LV-CAN200 and ALL-CAN300 CAN adapters support this feature. The version of the CAN adapter can be checked by sending an SMS command [[FMB_lvcangetinfo|lvcangetinfo]]. If, in the response message, <b>"SWRev:"</b> is <b>145</b>, the CAN adapter is older and if it is <b>245</b>, the adapter is newer. It does not apply to CAN-CONTROL - all CAN-CONTROL adapters support firmware updates over the air.
In order to update your device‘s firmware please follow a quick and simple step-by-step guide below. The procedure is the same for all devices.
In order to update your device‘s firmware please follow a quick and simple step-by-step guide below. The procedure is the same for all devices.
*FMB1YX device, which is connected to the CAN adapter (or [[FMB140]] which has an internal CAN adapter), must be registered in FOTA WEB – device‘s model, firmware version, serial number, and other information must be shown.
*FMx1YX device, which is connected to the CAN adapter (or [[FMB140]] which has an internal CAN adapter), must be registered in FOTA WEB – device‘s model, firmware version, serial number, and other information must be shown.
*FMB1YX device, which is connected to the CAN adapter, must have a correct firmware version uploaded. Currently, this feature is supported from firmware 03.25.15.Rev.143 (FMB140 Firmware version), however it is suggested to use Firmware version which is 03.25.16.Rev.410 [[FMB140_firmware_errata|FMB140]]. If you want to update your CAN Adapter, please contact your local Teltonika sales manager or Teltonika GPS technical support. Once a device with the correct firmware version connects to FOTA WEB on the next scheduled connection (or instant connection, initiated by an SMS command "web_connect"), a small, blue, „CAN“ logo will appear next to the device‘s model. And current version of the CAN adapter software can be checked in the table on the right.
* Once a device connects to FOTA WEB on the next scheduled connection (or instant connection, initiated by an SMS command "web_connect"), a small „CAN“ logo will appear next to the device‘s IMEI number. And current version of the CAN adapter software can be checked in the table at the bottom of the page.
[[Image:11I registered.jpg|1160x1160px|center]]
[[Image:11I registered.jpg|1160x1160px|center]]
*In order to update the software of a CAN adapter, You should follow these steps:
*In order to update the software of a CAN adapter, You should follow these steps:
*#Select the devices by clicking the check-box next to them
*#Select the devices by clicking the checkbox next to them
*#Press "'''Create task'''" at the top-left corner of the page
*#Press "'''Create task'''" at the top-left corner of the page
*#Select "'''Update CAN adapter firmware'''" task type
*#Select "'''Update CAN adapter firmware'''" task type
*Once the software update task has been assigned, it can be seen in the main window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):
*Once the software update task has been assigned, it can be seen in the main window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):
*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB(or instant connection, initiated by an SMS command "web_connect"):
*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB(or instant connection, initiated by an SMS command "web_connect"):
*<b>FMB150</b> CAN configuration can be uploaded Over The Air by using FOTA WEB.
*<b>FMB150</b> CAN configuration can be uploaded Over The Air by using FOTA WEB.
*In order to download your vehicles CAN configuration please follow a quick and simple step-by-step guide below. FMB150 device, must be registered in FOTA WEB – device‘s model, firmware version, serial number, and other information must be shown.
*In order to download your vehicle's CAN configuration please follow a quick and simple step-by-step guide below. FMB150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
*#Select the devices by clicking the check-box next to them
*#Select the devices by clicking the checkbox next to them
*#Press "Create task" at the top-left corner of the page
*#Press "Create task" at the top-left corner of the page
*#Select „Upload CAN configuration“ task type
*#Select „Upload CAN configuration“ task type
