Line 3: |
Line 3: |
| == Vehicle installation == | | == Vehicle installation == |
| | | |
− | 1. Clean the spots on the windshield with the ''alcohol wipe'' where you plan to mount the hardware. Remove the red 3M tape and mount the main unit underneath the rear-view mirror as centered (left/right) and straight as possible (if it ''must be off center'' by a few inches, that’s okay – measurements will be taken later). Be certain not to obstruct the drivers view.[[File:Vehinst1.jpg|center|frameless|191x191px|d<br />]] | + | 1. Clean the spots on the windshield with the ''alcohol wipe'' where you plan to mount the hardware. Remove the red 3M tape and mount the main unit underneath the rear-view mirror as centered (left/right) and straight as possible (if it ''must be off center'' by a few inches, that’s okay – measurements will be taken later). Be certain not to obstruct the drivers view. |
| + | |
| + | [[File:Vehinst1.jpg|frameless|191x191px|d<br />]] |
| + | |
| 2. Run the main-unit cable across the headliner and down to the driver side under-dash. This may require removing the A-pillar temporarily. Follow factory harnesses, always run behind any airbags. | | 2. Run the main-unit cable across the headliner and down to the driver side under-dash. This may require removing the A-pillar temporarily. Follow factory harnesses, always run behind any airbags. |
− | 3. Attach the mount (from the plastic bag) and stick the LCD indicator on the windshield in the driver’s line-of-sight, usually close to the A-pillar so it can be easily seen and controlled if required. Run this cable down to the driver’s under-dash as well.[[File:Vehinst2.jpg|center|frameless]] | + | |
| + | 3. Attach the mount (from the plastic bag) and stick the LCD indicator on the windshield in the driver’s line-of-sight, usually close to the A-pillar so it can be easily seen and controlled if required. Run this cable down to the driver’s under-dash as well. |
| + | |
| + | [[File:Vehinst2.jpg|frameless]] |
| + | |
| 4. Once both cables are run to the under-dash, connect them to the provided PCI unit at the proper ports. | | 4. Once both cables are run to the under-dash, connect them to the provided PCI unit at the proper ports. |
| | | |
Line 11: |
Line 18: |
| | | |
| 5. Connect the Teltonika FMx125,FMX225 tracker to the main unit using RS232 cable. Please refer connection scheme below. | | 5. Connect the Teltonika FMx125,FMX225 tracker to the main unit using RS232 cable. Please refer connection scheme below. |
| + | |
| [[File:ADAS wiring scheme 2.png|center|frameless|1160x1160px]] | | [[File:ADAS wiring scheme 2.png|center|frameless|1160x1160px]] |
| | | |
Line 37: |
Line 45: |
| | | |
| 6. Connect the provided Power/Ground harness connection to a chassis ground (black wire) and Ignition source (red wire). The circuit must provide ~3 Amp @12v. Connect the plug to the PCI unit at the ‘Power’ port. | | 6. Connect the provided Power/Ground harness connection to a chassis ground (black wire) and Ignition source (red wire). The circuit must provide ~3 Amp @12v. Connect the plug to the PCI unit at the ‘Power’ port. |
− | [[File:Vehinst8.png|center|frameless|357x357px]] | + | |
| + | [[File:Vehinst8.png|frameless|357x357px]] |
| | | |
| == Installation: for CAN-equipped vehicles == | | == Installation: for CAN-equipped vehicles == |