Difference between revisions of "FTC881 Features"
(Created page with "==Overspeeding== right|300 px When vehicle speed exceeds configured maximum speed value the scenario is activated, and an event record is gen...") |
|||
| (17 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | ==Overspeeding== |
| − | + | [[File:FTC921_Overspeeding.png|right|300 px]] | |
| − | | | + | |
| − | }} | + | When vehicle speed exceeds configured maximum speed value the scenario is activated, and an event record is generated{{{text_dout| and digital output status is changed to 1 when configured}}}.<br />Detected speed has to be greater than configured max speed +3% of configured max speed for the overspeeding event to start. To stop overspeeding event detected speed has to be lower than configured max speed -3% of configured max speed. |
| + | Configurable parameters: | ||
| + | |||
| + | <br /> | ||
| + | *Priority – defines the priority of overspeeding scenario: 0 – disabled, 1 – low, 2 – high, 3 – panic. | ||
| + | *Max speed – it is the maximum allowed speed that can be reached. If the speed exceeded configured value, then the event will occur. | ||
| + | |||
| + | ==Trip== | ||
| + | [[File:FTC921_Trip.png|right|300 px]] | ||
| + | |||
| + | ''Trip''' section offers user to configure the ''Trip'' feature. ''Trip'' starts when Ignition according ''Ignition source'' is ON and Movement according ''Movement source'' is ON and also 'Start Speed' is exceeded. ''Start Speed'' defines the minimum GPS speed in order to detect ''Trip'' start.<br/>''Ignition OFF Timeout'' is the timeout value to detect ''Trip'' end once the Ignition (configured ignition source) is off.<br/>I/O Trip Odometer must be enabled to use ''Distance counting mode'' feature. When it is set to <span style=color:#F6A83E>Continuous</span>, ''Trip'' distance is going to be counted continuously (from ''Trip'' start to ''Trip'' end) and written to I/O ''Trip Odometer'' value field. When ''Trip'' is over and the next ''Trip'' begins, ''Trip Odometer'' value is reset to zero.<br/>When ''Mode'' is set to <span style=color:#F6A83E>Between Records</span>, the distance is going to be counted between every record made. This value is written to I/O ''Trip Odometer'' value field and is reset to zero every new record until the ''Trip'' ends. If later all Odometer values are summed up manually, the distance driven during the whole duration of the ''Trip'' can be obtained.<br/> | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | ==Odometer settings== | ||
| + | [[File:FTC921_Odometer_settings.png|right|300 px]] | ||
| + | |||
| + | {{{par_src|''Calculation Source'' allows to choose Odometer calculation source between <span style=color:#F6A83E>GNSS</span>, <span style=color:#F6A83E>OBD</span>.<br/>}}}''Odometer Value'' sets the starting total odometer value. | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | ==Unplug detection== | ||
| + | [[File:FTC921_Unplug_detection.png|right|300 px]] | ||
| + | |||
| + | An event will be generated when {{{model|FMB1YX}}} is unplugged from {{{txt_src|external power}}} or plugged back in again. | ||
| + | '''Priority''' | ||
| + | * '''Disable''' - disable scenario. | ||
| + | * '''Low Priority''' - when low priority event is triggered, device '''makes additional record''' with indication of event cause. | ||
| + | * '''High Priority''' - module makes additional record with High priority flag and '''sends event packet immediately''' to the server by | ||
| + | '''GPRS'''. | ||
| + | |||
| + | |||
| + | ==Static navigation== | ||
| + | [[File:FTC921_Static_navigation.png|right|300 px]] | ||
| + | |||
| + | ''Static Navigation Mode'' is a filter, which filters out track jumps when the object is stationary.<br></br> | ||
| + | If the Static navigation filter is disabled, it will apply no changes to GPS data. If the Static navigation filter is enabled, it will filter changes in GPS position if no movement (configured movement source) or ignition (configured ignition source) is detected (depends on what static navigation settings are selected: movement, ignition or both sources). It allows filtering GPS jumps when an object is parked (is not moving) and GPS position is still traced.<br></br> | ||
| + | |||
| + | |||
| + | ==Digital output overcurrent recovery== | ||
| + | [[File:FTC921_Digital_output_overcurrent_recovery.png|right|300 px]] | ||
| + | |||
| + | |||
| + | [[Category:FTC881 Configuration]] | ||
Revision as of 13:58, 1 June 2023
Main Page > Basic Trackers > FTC921 > FTC921 Configuration > FTC881 FeaturesOverspeeding
When vehicle speed exceeds configured maximum speed value the scenario is activated, and an event record is generated and digital output status is changed to 1 when configured.
Detected speed has to be greater than configured max speed +3% of configured max speed for the overspeeding event to start. To stop overspeeding event detected speed has to be lower than configured max speed -3% of configured max speed.
Configurable parameters:
- Priority – defines the priority of overspeeding scenario: 0 – disabled, 1 – low, 2 – high, 3 – panic.
- Max speed – it is the maximum allowed speed that can be reached. If the speed exceeded configured value, then the event will occur.
Trip
Trip' section offers user to configure the Trip feature. Trip starts when Ignition according Ignition source is ON and Movement according Movement source is ON and also 'Start Speed' is exceeded. Start Speed defines the minimum GPS speed in order to detect Trip start.
Ignition OFF Timeout is the timeout value to detect Trip end once the Ignition (configured ignition source) is off.
I/O Trip Odometer must be enabled to use Distance counting mode feature. When it is set to Continuous, Trip distance is going to be counted continuously (from Trip start to Trip end) and written to I/O Trip Odometer value field. When Trip is over and the next Trip begins, Trip Odometer value is reset to zero.
When Mode is set to Between Records, the distance is going to be counted between every record made. This value is written to I/O Trip Odometer value field and is reset to zero every new record until the Trip ends. If later all Odometer values are summed up manually, the distance driven during the whole duration of the Trip can be obtained.
Odometer settings
Calculation Source allows to choose Odometer calculation source between GNSS, OBD.
Odometer Value sets the starting total odometer value.
Unplug detection
An event will be generated when FMB1YX is unplugged from external power or plugged back in again. Priority
- Disable - disable scenario.
- Low Priority - when low priority event is triggered, device makes additional record with indication of event cause.
- High Priority - module makes additional record with High priority flag and sends event packet immediately to the server by
GPRS.
Static Navigation Mode is a filter, which filters out track jumps when the object is stationary.
If the Static navigation filter is disabled, it will apply no changes to GPS data. If the Static navigation filter is enabled, it will filter changes in GPS position if no movement (configured movement source) or ignition (configured ignition source) is detected (depends on what static navigation settings are selected: movement, ignition or both sources). It allows filtering GPS jumps when an object is parked (is not moving) and GPS position is still traced.
Digital output overcurrent recovery
