Changes

<b>Please note</b>, that alternative wiring with DOUT is possible, in order to receive additional data from ADAS while the ignition is off, but the key is turned to the ACC position. That way it would be possible to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].

<b>Please note</b>, that alternative wiring with DOUT is possible, in order to receive additional data from ADAS while the ignition is off, but the key is turned to the ACC position. That way it would be possible to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].

[[File:ADAS_w_DOUT.jpg|800px]]

[[File:ADAS_w_DOUT.jpg]]

{| class="wikitable"

{| class="wikitable"

'''Please note that camera must be connected to an ignition source, in other way the camera will drain battery'''

'''Please note that camera must be connected to an ignition source, in other way the camera will drain battery'''

For FMX640 devices, RJ45 cable is required with one end cut and loose. Connect the RJ45 cable to the FMX640 device's port 1 or port 2, both slots have RS232 support. Once connected, the other end of the cable should have pin 3-Rx, and 4-Tx shaved and connected to ADAS camera Rx and Tx cable. For the rest of the connection please refer to the picture below.

'''Also, some RJ45 cables have two modifications, some have RS232 output on 3/4 pins some on 5/6 pins'''

[[File:Adas112233.jpeg]]

If it is necessary to receive additional data from the ADAS when the ignition is off but the key is inserted and turned to the ACC position, you can do it by connecting the camera to a power source using a relay in order to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].

'''ADAS connection with relay'''

If it is necessary to receive additional data from the DSM when the ignition is off but the key is inserted and turned to the ACC position, you can do it by connecting the camera to a power source using a relay in order to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].

 

'''Two cameras FMC650 Installation with Relay'''

. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].

 

 

'''Two cameras FMC650 Installation with Ignition Source.''' To connect the two cameras to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.

[[File:ADAS_w_DOUT6.jpg|800px]]

NOTE: Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.  

{| class="wikitable"

{| class="wikitable"

* Enable  Transmit data RS-232 feature

* Enable  Transmit data RS-232 feature

(Converter mode should be selected to work with  FMx125).  

(115200 mode should be selected to work with  FMx125).  

It allows ADAS event data transmission to integrated device.

It allows ADAS event data transmission to integrated device.

* Enable  Vibration setting for LDW, FCW, PCW (On / Off / Both).  

* Enable  Vibration setting for LDW, FCW, PCW (On / Off / Both).  

You can check the connection with the button.

You can check the connection with the button.

|[[File:Mdconfi6.1.png|center|frameless]]

|[[File:Image (3).png|center|frameless]]

|-

|-

| colspan="2" |'''Miscellaneous  Settings:'''

| colspan="2" |'''Miscellaneous  Settings:'''