0
edits
Changes
Technoton DUT-E S7 Fuel Level Sensor (view source)
Revision as of 12:21, 5 October 2020
, 12:21, 5 October 2020Created page with "==Introduction to the product== DUT-E S7 Fuel Level Sensor connected to FMB using the Bluetooth interface. <br><br> 400px <br> ==DUT-E..."
==Introduction to the product==
DUT-E S7 Fuel Level Sensor connected to FMB using the Bluetooth interface. <br><br>
[[image:Dut-e-s7 s donnim uporom.png|400px]] <br>
==DUT-E S7 fuel level sensor connection==
The DUT-E S7 fuel level sensor is to be switched to the Working mode according to the operation manual.<br>
To obtain the MAC address of the DUT-E S7 fuel level sensor, you need to transfer the sensor number from decimal to hexadecimal code.<br>
[[image:Dut-e-s7 hex.png]]
<br>
==Teltonika FMB 120 connection==
Insert a SIM card and supply power to the TELTONIKA FMВ 120 terminal. <br>
Note: Firmware 03.27.01 Rev:00 or latest.
==Equipment and fuel level sensor calibration==
===Terminal settings in the Configurator===
Configure the GPRS data of the SIM card operator and the address of the telematic server:<br>
Note: Configurator v1.6.4B.3.27 R2 or latest according to the firmware version
[[image:Dut-e-s7 configurator.png|800px|center]]
<br>
Choose the protocol as shown below:<br>
[[image:Dut-e-s7 configurator2.png|800px|center]]
===Connection of the fuel level sensor to the terminal===
Put the sensors near the terminal. <br>
Make ‘Discovering’ of the sensors:
[[File:Dut-e-s7 configurator3.png|800px|center]]
<br>
[[File:Dut-e-s7 configurator4.png|800px|center]]
<br>
Fill the MAC address in the field:
[[File:Dut-e-s7 configurator5.png|800px|center]]
<br>
Configure the terminal for the data transfer from the fuel level sensor:
[[File:Dut-e-s7 configurator6.png|800px|center]]
<br>
Select a preset from a list for the sensor:
[[File:Dut-e-s7 configurator7.png|800px|center]]
<br>
[[File:Dut-e-s7 configurator8.png|800px|center]]
<br>
It is possible to connect up to 4 DUT-E S7 sensors.<br>
The sensor settings are similar; you only need to change the MAC address.<br><br>
None - PGN number (63277);<br>
Fuel Frequency - frequency Hz DUT S7 (fuel level);<br>
Temperature - temperature С0 of DUT S7;<br>
Custom1 - Lateral acceleration m/s2 (reserve);<br>
Custom2 - Longitudinal acceleration m/s2 (reserve);<br>
Custom3 - Vertical acceleration m/s2 (reserve);<br>
Custom4 - DTCs mask.<br><br>
Frequency, temperature, and DTCs mask data are displayed in the configurator. Press the Low button to select the parameter to be sent to the server:
[[File:Dut-e-s7 configurator9.png|800px|center]]
<br>
BLE Temperature 1 - temperature С0;<br>
BLE 1 Custom4 - DTCs mask.<br>
BLE Fuel Frequency 1 - frequency Hz (fuel level).<br><br>
At the moment, the accelerometer is not implemented in the current DUT-E S7 firmware:<br>
Custom1 - Lateral acceleration m/s2 (reserve);<br>
Custom2 - Longitudinal acceleration m/s2 (reserve);<br>
Custom3 - Vertical acceleration m/s2 (reserve);<br>
FFFF (65535) values are transmitted on three planes.<br>
==Data on the telematics server==
Sign in the terminal on the telematics server.<br>
Configure the temperature and fuel level sensors DTCs masks.<br>
The data on the server will look like this:
[[File:Telematics server 1.png|800px|center]]
<br>
Sensors configuration:
[[File:Telematics server 2.png|800px|center]]
<br>
===Temperature sensor configuration===
<br>
[[File:Telematics server 3.png|800px|center]]
<br>
===Fuel level sensor configuration===
<br>
[[File:Telematics server 4.png|800px|center]]
<br>
Calibrate the fuel level sensor, the ratio of the output frequency to the volume of fuel in the tank:
[[File:Telematics server 5.png|800px|center]]
<br>
===DTCs mask sensor configuration===
<br>
[[File:Telematics server 6.png|800px|center]]
<br>
The configures sensors will look like:
[[File:Telematics server 7.png|800px|center]]
<br><br>
DUT-E S7 Fuel Level Sensor connected to FMB using the Bluetooth interface. <br><br>
[[image:Dut-e-s7 s donnim uporom.png|400px]] <br>
==DUT-E S7 fuel level sensor connection==
The DUT-E S7 fuel level sensor is to be switched to the Working mode according to the operation manual.<br>
To obtain the MAC address of the DUT-E S7 fuel level sensor, you need to transfer the sensor number from decimal to hexadecimal code.<br>
[[image:Dut-e-s7 hex.png]]
<br>
==Teltonika FMB 120 connection==
Insert a SIM card and supply power to the TELTONIKA FMВ 120 terminal. <br>
Note: Firmware 03.27.01 Rev:00 or latest.
==Equipment and fuel level sensor calibration==
===Terminal settings in the Configurator===
Configure the GPRS data of the SIM card operator and the address of the telematic server:<br>
Note: Configurator v1.6.4B.3.27 R2 or latest according to the firmware version
[[image:Dut-e-s7 configurator.png|800px|center]]
<br>
Choose the protocol as shown below:<br>
[[image:Dut-e-s7 configurator2.png|800px|center]]
===Connection of the fuel level sensor to the terminal===
Put the sensors near the terminal. <br>
Make ‘Discovering’ of the sensors:
[[File:Dut-e-s7 configurator3.png|800px|center]]
<br>
[[File:Dut-e-s7 configurator4.png|800px|center]]
<br>
Fill the MAC address in the field:
[[File:Dut-e-s7 configurator5.png|800px|center]]
<br>
Configure the terminal for the data transfer from the fuel level sensor:
[[File:Dut-e-s7 configurator6.png|800px|center]]
<br>
Select a preset from a list for the sensor:
[[File:Dut-e-s7 configurator7.png|800px|center]]
<br>
[[File:Dut-e-s7 configurator8.png|800px|center]]
<br>
It is possible to connect up to 4 DUT-E S7 sensors.<br>
The sensor settings are similar; you only need to change the MAC address.<br><br>
None - PGN number (63277);<br>
Fuel Frequency - frequency Hz DUT S7 (fuel level);<br>
Temperature - temperature С0 of DUT S7;<br>
Custom1 - Lateral acceleration m/s2 (reserve);<br>
Custom2 - Longitudinal acceleration m/s2 (reserve);<br>
Custom3 - Vertical acceleration m/s2 (reserve);<br>
Custom4 - DTCs mask.<br><br>
Frequency, temperature, and DTCs mask data are displayed in the configurator. Press the Low button to select the parameter to be sent to the server:
[[File:Dut-e-s7 configurator9.png|800px|center]]
<br>
BLE Temperature 1 - temperature С0;<br>
BLE 1 Custom4 - DTCs mask.<br>
BLE Fuel Frequency 1 - frequency Hz (fuel level).<br><br>
At the moment, the accelerometer is not implemented in the current DUT-E S7 firmware:<br>
Custom1 - Lateral acceleration m/s2 (reserve);<br>
Custom2 - Longitudinal acceleration m/s2 (reserve);<br>
Custom3 - Vertical acceleration m/s2 (reserve);<br>
FFFF (65535) values are transmitted on three planes.<br>
==Data on the telematics server==
Sign in the terminal on the telematics server.<br>
Configure the temperature and fuel level sensors DTCs masks.<br>
The data on the server will look like this:
[[File:Telematics server 1.png|800px|center]]
<br>
Sensors configuration:
[[File:Telematics server 2.png|800px|center]]
<br>
===Temperature sensor configuration===
<br>
[[File:Telematics server 3.png|800px|center]]
<br>
===Fuel level sensor configuration===
<br>
[[File:Telematics server 4.png|800px|center]]
<br>
Calibrate the fuel level sensor, the ratio of the output frequency to the volume of fuel in the tank:
[[File:Telematics server 5.png|800px|center]]
<br>
===DTCs mask sensor configuration===
<br>
[[File:Telematics server 6.png|800px|center]]
<br>
The configures sensors will look like:
[[File:Telematics server 7.png|800px|center]]
<br><br>
