1,645
edits
Changes
→2. Configuring FMX6XX:
The main parameters that you need to configure will be the SIM1 or SIM2 APN password and APN username so that you will protect the device from another user to send SMS/GPRS commands to the device.
The main parameters that you need to configure will be the SIM1 or SIM2 APN password and APN username so that you will protect the device from another user to send SMS/GPRS commands to the device.
The second step will be to configure the server PORT DOMAIN and what sending protocol will be TCP or UDP depends on the server to which you will send the data from the device and tachograph ( also you can configurate back up server if server #1 will not available to receive data) to properly configure the server you need to select which server you will be using, more platforms you can find here [https://wiki.teltonika-gps.com/view/Fleet_Management_platforms Fleet Management platforms]
The second step will be to configure the server PORT DOMAIN and what sending protocol will be TCP or UDP depends on the server to which you will send the data from the device and tachograph ( also you can configure back up the server if server #1 will not available to receive data) to properly configure the server you need to select which server you will be using, more platforms you can find here [https://wiki.teltonika-gps.com/view/Fleet_Management_platforms Fleet Management platforms]
In the picture below you can find were located GPRS settings and what settings need to be configured:
In the picture below you can find were located GPRS settings and what settings need to be configured:
[[File:Sfmb6440.jpg|frameless|606x606px]]
[[File:Sfmb6440.jpg|frameless|606x606px]]
====2.2 Configurating [https://wiki.teltonika-gps.com/view/FMB640_System_settings System settings]====
The second main parameter to configure is the movement source and ignition source.
Movement source parameter, which determines if the device should work in "Vehicle on Stop" or "Vehicle on Moving" mode. There are four possible movement sources:
* Ignition - if Ignition (based on Ignition Source) is ON, Vehicle MOVING mode is used; if Ignition is OFF, Vehicle on STOP mode is used;
* Movement - if accelerometer detects movement, Vehicle MOVING mode is used; if no movement is detected, Vehicle on STOP mode is used;
* GNSS' - if GPS Fix is acquired and the vehicle speed is >=5 km/h, Vehicle MOVING mode is used; if GPS speed is <5 km/h, Vehicle on STOP mode is used (if there is no GPS Fix, accelerometer determines vehicle modes);
* CAN Speed - if CAN adapter or FMS speed is >0 km/h, Vehicle MOVING mode is used; if CAN adapter or FMS speed is <=0 km/h, Vehicle on STOP mode is used;
An ignition source will be used to determine the ignition of the vehicle. If voltage is between High Voltage Lever and Low Voltage Level (below Ignition Settings options) - ignition is ON. If voltage is higher than High Voltage Lever or lower than Low Voltage Level - ignition is OFF.
* Digital Input 1 - if Digital Input 1 is 1 - ignition is ON; if Digital Input 1 value is 0 - ignition is OFF;
* Digital Input 2 - if Digital Input 2 is 1 - ignition is ON; if Digital Input 2 value is 0 - ignition is OFF;
* Digital Input 3 - if Digital Input 3 is 1 - ignition is ON; if Digital Input 3 value is 0 - ignition is OFF;
* Digital Input 4 - if Digital Input 4 is 1 - ignition is ON; if Digital Input 4 value is 0 - ignition is OFF;
* Power Voltage - if the voltage is between High Voltage Lever and Low Voltage Level (below Ignition Settings options) - ignition is ON; if the voltage is higher than High Voltage Lever or lower than Low Voltage Level - ignition is OFF.
* Movement - if Movement is still detected 1 after Movement Start Delay (s) - ignition is ON; if Movement value is 0 after Movement Stop Delay (s) - ignition is OFF;
Example: DIN1 and Movement are selected as the Ignition source. When the device detects movement, Ignition status will change to 1, regardless that the DIN1 value is 0.
In the picture below you can find were located System settings and what settings need to be configured:
Example: DIN1 and Accelerometer are selected as the Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. Users can select movement start and movement stop delay time - those parameters are used when the accelerometer is selected as an ignition source. Ignition status is used in power management
==='''3. Configuring Digital Tachograph Monitoring:'''===
==='''3. Configuring Digital Tachograph Monitoring:'''===
