104
edits
Changes
Inateck BCST-70 Configuration (view source)
Revision as of 10:18, 27 April 2023
, 10:18, 27 April 2023Created page with "{| align="right" |__TOC__ |} ==Configure FM device using Teltonika configurator== </br> #In System settings, enable Codec8 Extended</br></br>File:Data_Protocol.png|bor..."
{| align="right"
|__TOC__
|}
==Configure FM device using Teltonika configurator==
</br>
#In System settings, enable Codec8 Extended</br></br>[[File:Data_Protocol.png|border|250px]]</br></br>
#In GPRS settings, configure GPRS Settings and Server Settings.</br></br>
#In Bluetooth settings,
::*Enable Bluetooth, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth will be disabled
::*Under Bluetooth Control, click Discover so it would detect devices within vicinity. </br></br>[[File:Bluetooth_Control.png|border|200px]]</br></br>
::*Once devices are discovered, select BCST-70-XXXX-SPP then proceed to tick Pair
::*After successful pairing, scanner should show under Paired Devices. </br></br>[[File:Paired_Devices.png|border|200px]]</br></br>
<span style="color:#FF0000">'''NOTE:'''</span> : '' If in case the Scanner is not discovered, do the following steps on Bluetooth Pairing.''
==Enable Bluetooth Pairing==
<ol style="list-style-type:lower-alpha">
<li>Scan “Enter Setup” </br></br>[[File:Enter_Setup.png|325px]]</br></br></li>
<li>Scan “ Bluetooth Pairing” </br></br>[[File:Bluetooth_Pairing.png|325px]]</br></br></li>
<li>Scan the "Exit with Save" barcode </br></br>[[File:Exit_Save.png|325px]]</br></br></li>
</ol>
==Scanner Auto Connect Configuration==
</br>
*Fill up the “Auto Connect To External Device“ with as follows: </br></br>[[File:External_Device.png|border|250px]]</br></br>
::*Select Connection Mode as, Inateck Scanner.
::*Enter the External MAC, can be seen on Paired Devices at the upper left corner.
::*Enter the External Name, can be seen on Paired Devices at the lower right corner.
::*Enter the External Pin, if the scanner has pin code set otherwise leave as blank.</br>
*Fill up the “Authorized Devices MAC List“ same with the External MAC. </br></br>[[File:Authorized_Mac.png|border|250px]]
<span style="color:#FF0000">'''NOTE:'''</span> : '' It is important to fill out the auto connect so you won‘t need to Pair the device again on the Configurator.''
*To receive the data to server enable corresponding BT Status IO element to Low. </br></br>[[File:BT_Status.png|border|500px]]
<span style="color:#FF0000">'''NOTE:'''</span> : ''If Scanner is connected BT Status value would be read as 2''
[[Category:Inateck BCST-70 Barcode Scanner]]
|__TOC__
|}
==Configure FM device using Teltonika configurator==
</br>
#In System settings, enable Codec8 Extended</br></br>[[File:Data_Protocol.png|border|250px]]</br></br>
#In GPRS settings, configure GPRS Settings and Server Settings.</br></br>
#In Bluetooth settings,
::*Enable Bluetooth, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth will be disabled
::*Under Bluetooth Control, click Discover so it would detect devices within vicinity. </br></br>[[File:Bluetooth_Control.png|border|200px]]</br></br>
::*Once devices are discovered, select BCST-70-XXXX-SPP then proceed to tick Pair
::*After successful pairing, scanner should show under Paired Devices. </br></br>[[File:Paired_Devices.png|border|200px]]</br></br>
<span style="color:#FF0000">'''NOTE:'''</span> : '' If in case the Scanner is not discovered, do the following steps on Bluetooth Pairing.''
==Enable Bluetooth Pairing==
<ol style="list-style-type:lower-alpha">
<li>Scan “Enter Setup” </br></br>[[File:Enter_Setup.png|325px]]</br></br></li>
<li>Scan “ Bluetooth Pairing” </br></br>[[File:Bluetooth_Pairing.png|325px]]</br></br></li>
<li>Scan the "Exit with Save" barcode </br></br>[[File:Exit_Save.png|325px]]</br></br></li>
</ol>
==Scanner Auto Connect Configuration==
</br>
*Fill up the “Auto Connect To External Device“ with as follows: </br></br>[[File:External_Device.png|border|250px]]</br></br>
::*Select Connection Mode as, Inateck Scanner.
::*Enter the External MAC, can be seen on Paired Devices at the upper left corner.
::*Enter the External Name, can be seen on Paired Devices at the lower right corner.
::*Enter the External Pin, if the scanner has pin code set otherwise leave as blank.</br>
*Fill up the “Authorized Devices MAC List“ same with the External MAC. </br></br>[[File:Authorized_Mac.png|border|250px]]
<span style="color:#FF0000">'''NOTE:'''</span> : '' It is important to fill out the auto connect so you won‘t need to Pair the device again on the Configurator.''
*To receive the data to server enable corresponding BT Status IO element to Low. </br></br>[[File:BT_Status.png|border|500px]]
<span style="color:#FF0000">'''NOTE:'''</span> : ''If Scanner is connected BT Status value would be read as 2''
[[Category:Inateck BCST-70 Barcode Scanner]]
