CAN Adapter update: Difference between revisions

From Teltonika Telematics Wiki
No edit summary
No edit summary
 
(60 intermediate revisions by 15 users not shown)
Line 1: Line 1:
Teltonika is proud to announce a new, easier way to update Teltonika‘s [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] adapters' software by using [[FOTA WEB]]. The feature is also supported by our fresh [[FMB140]] device which has a built-in CAN bus reading adapter. This is an excellent solution because a special cable is no longer needed and the software of the CAN adapter can be updated remotely, without having to dismount the CAN adapter from the vehicle. Upgrading the software of a CAN adapter will add more program numbers, in other words – more vehicle models will be supported.
__TOC__
==CAN Adapter update==
The software of CAN adapters - [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] can now be updated Over The Air by using [[FOTA WEB]] and one of the FMx1YX devices. Upgrading the software of the CAN adapter will add more program numbers, thus, more vehicle models will be supported.


In order to update your device‘s firmware please follow a quick and simple step-by-step guide which is below. The procedure is the same for all devices.
<b>Please note</b>, that only the newer version of LV-CAN200 and ALL-CAN300 CAN adapters support this feature. The version of the CAN adapter can be checked by sending an SMS command [[FMB_lvcangetinfo|lvcangetinfo]]. If, in the response message, <b>"SWRev:"</b> is <b>145</b>, the CAN adapter is older and if it is <b>245</b> or higher number, the adapter is newer. It does not apply to CAN-CONTROL - all CAN-CONTROL adapters support firmware updates over the air.


*FMB1YX device, which is connected to the CAN adapter (or [[FMB140]] which has internal CAN adapter), must be registered in Fota Web – device‘s model, firmware version, serial number and other information must be shown.
In order to update your device adapters firmware please follow a quick and simple step-by-step guide below. The procedure is the same for all devices.


*A correct firmware version must be uploaded to the FMB1YX device. Currently this feature is only supported with firmware version 03.25.11.Rev141. If, firmware version is correct, a small, blue, „CAN“ logo will appear next to the device‘s model, once it connects to Fota Web:
*FMx1YX device, which is connected to the CAN adapter (or [[FMB140]] which has an internal CAN adapter), must be registered in FOTA WEB – device‘s model, firmware version, serial number, and other information must be shown.


[[Image:FM registered.jpg|1160x1160px|center]]
* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.
[[File:CAN adapter version 2024.png|center]]


*A current version of the CAN adapter version can be checked by pressing a small „i“ button on the right. All FMB1YX device‘s and CAN adapter‘s details are listed in one window:


[[Image:FM OldDate.jpg|1162x1162px|center]]
*In order to update the software of a CAN adapter, You should follow these steps:
*#Select the devices by clicking the checkbox next to them
*#Press "'''Create task'''" at the top-left corner of the page
*#Select "'''Upload CAN adapter firmware'''" task type
[[File:CAN Adapter update 2024.gif|center]]


*If the software is not up-to-date it can be updated in the main window. A check-box needs to be ticked, then „Actions“ button pressed and „Update CAN adapter firmware“ selected:
*Once the software update task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").


[[File:FMB120 + LV-CAN200 Fota details in progress.jpg|alt=|center|1159x1159px]]
*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").


*Once the software update task has been assigned, it can be seen in the main window:
==FMx150 CAN OEM file upload==


[[Image:FM Assigned.jpg|1155x1155px|center]]
*<b>FMx150</b> CAN OEM file can be uploaded Over The Air by using FOTA WEB.


*When the update is finished, a new software version can be seen in the details window:
*In order to upload your vehicle's CAN OEM file please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
*#Select the devices by clicking the checkbox next to them
*#Press "Create task" at the top-left corner of the page
*#Select "Upload CAN OEM file" task type
*#Select Vehicle Make, and Model:
[[File:150 OEM upload 2024.gif|center]]


[[Image:FM Done.jpg|1162x1162px|center]]
*Once the CAN OEM file upload task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
*When the update is finished, a new vehicle make and model can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
 
 
==FMx150 CAN chip update==
 
*In order to update your device CAN chip firmware please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
*#Select the devices by clicking the checkbox next to them
*#Press "Create task" at the top-left corner of the page
*#Select "Upload CAN chip firmware" task type
*#Select required CAN chip firmware version:
[[File:150 Chip update 2024.gif|center]]
 
*Once the CAN chip firmware update task has been assigned, it can be seen in the Tasks window. Please note, that updating will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
*When the update is finished, a new CAN chip version can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
 
[[Category: Frequently Asked Questions - FAQ]]

Latest revision as of 16:52, 3 December 2024

Main Page > Frequently Asked Questions - FAQ > CAN Adapter update

CAN Adapter update

The software of CAN adapters - LV-CAN200, ALL-CAN300 and CAN-CONTROL can now be updated Over The Air by using FOTA WEB and one of the FMx1YX devices. Upgrading the software of the CAN adapter will add more program numbers, thus, more vehicle models will be supported.

Please note, that only the newer version of LV-CAN200 and ALL-CAN300 CAN adapters support this feature. The version of the CAN adapter can be checked by sending an SMS command lvcangetinfo. If, in the response message, "SWRev:" is 145, the CAN adapter is older and if it is 245 or higher number, the adapter is newer. It does not apply to CAN-CONTROL - all CAN-CONTROL adapters support firmware updates over the air.

In order to update your device adapters firmware please follow a quick and simple step-by-step guide below. The procedure is the same for all devices.

  • FMx1YX device, which is connected to the CAN adapter (or FMB140 which has an internal CAN adapter), must be registered in FOTA WEB – device‘s model, firmware version, serial number, and other information must be shown.
  • Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.


  • In order to update the software of a CAN adapter, You should follow these steps:
    1. Select the devices by clicking the checkbox next to them
    2. Press "Create task" at the top-left corner of the page
    3. Select "Upload CAN adapter firmware" task type
  • Once the software update task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
  • When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").

FMx150 CAN OEM file upload

  • FMx150 CAN OEM file can be uploaded Over The Air by using FOTA WEB.
  • In order to upload your vehicle's CAN OEM file please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
    1. Select the devices by clicking the checkbox next to them
    2. Press "Create task" at the top-left corner of the page
    3. Select "Upload CAN OEM file" task type
    4. Select Vehicle Make, and Model:
  • Once the CAN OEM file upload task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
  • When the update is finished, a new vehicle make and model can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").


FMx150 CAN chip update

  • In order to update your device CAN chip firmware please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
    1. Select the devices by clicking the checkbox next to them
    2. Press "Create task" at the top-left corner of the page
    3. Select "Upload CAN chip firmware" task type
    4. Select required CAN chip firmware version:
  • Once the CAN chip firmware update task has been assigned, it can be seen in the Tasks window. Please note, that updating will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
  • When the update is finished, a new CAN chip version can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").