312
edits
Changes
→Crash Detection Functionality using DOUT
==Device configuration==
==FMX125/225 configuration==
*Please make sure to download the latest DashCam FW version. The latest FWs can be downloaded from the following Wiki page — [[DashCam Firmware errata]]
*It is necessary to change '''Data Protocol''' to [[Codec#Codec_8_Extended | Codec 8 Extended]]
*It is necessary to change '''Data Protocol''' to [[Codec#Codec_8_Extended | Codec 8 Extended]]
*'''Do not forget''' to configure ''DashCam'' server information. In '''RS232\RS485''' fill in '''DashCam Server Settings''' with ''Domain'' and ''Port'' entries.
*'''Do not forget''' to configure ''DashCam'' server information. In '''RS232\RS485''' fill in '''DashCam Server Settings''' with ''Domain'' and ''Port'' entries.
[[File:Dashcamserver.png|600px]]
[[File:Dashcamserver.png|600px]]
==FMC650 DashCam Configuration==
'''(!) Required firmware version - 03.00.14.Rev.114.''' [[DashCam Firmware errata|Firmware errata.]]
*Make sure '''Data Protocol''' is set to [[Codec#Codec_8_Extended | Codec 8 Extended]]
[[Image:Data_protocol.gif|300px]]
*In ''RS232 \ RS485 settings tab'', make sure to enable '''Camera interface''' by "Enable", and select '''DashCam''' in the Mode drop-down menu, afterwards '''DashCam COM1''' and '''Camera I/O''' should appear in the tab list.
[[Image:Dashcam config.gif|600px]]
*Make sure to change '''Camera I/O''' camera state '''Priorities''' to ''Low''
'''
[[File:DashCam priority.gif|500px]]
'''
*In appeared ''DashCam COM1'' tab, make sure to '''configure everything by your needs''', and do not forget to complete the '''"Domain"''' and '''"Port"''' settings in ''"DashCam" Scenario Settings''
[[File:DashCam COM1.png|500px]]
*'''''NOTE:''''' ''This is a base setup for the device to work properly. Other device configuration is made according to your needs.
*'''''NOTE:''''' ''This is a base setup for the device to work properly. Other device configuration is made according to your needs.
''
''
*'''''NOTE:''''' ''There are different settings for picture quality and compression, these settings will affect picture/video sizes and upload speeds. For more information about transfer sizes and timings, please visit our [[DashCam_Camera_Manual#DashCam_data_transfer_timing | DashCam Data Transfer Timing]] section
*'''''NOTE:''''' ''There are different settings for picture quality and compression, these settings will affect picture/video sizes and upload speeds. For more information about transfer sizes and timings, please visit our [[DashCam_Camera_Manual#DashCam_data_transfer_timing | DashCam Data Transfer Timing]] section
''
''
===Connecting two cameras simultaneously for FMx650===
------------------
The new feature for FMx650 DashCam configuration, which is available from '''03.00.14.Rev.114 iCamera''' allows you to connect two of your cameras at once. Method for connection and configuration stays the same, for this you are only required to choose '''two''' cameras in '''"RS232 \ RS485"''' tab from the configurator.
In the new functionality, you are able to connect any combo of the cameras by your wish, as an example: you are able to connect ''DashCam/Dualcam'', ''DashCam/DSM'', ''DSM/DSM'', ''DualCam/DualCam'' and etc.
[[File:Twincamera.gif|500px]]
==Camera Scenario Mode==
==Camera Scenario Mode==
Periodic image sending triggers photo capture from a front camera, whenever the timeout is reached (sending interval parameter).
Periodic image sending triggers photo capture from a front camera, whenever the timeout is reached (sending interval parameter).
'''Update: Since 03.27.03.Rev.04 firmware''', Periodic Image Sending Enable/Disable switch was replaced by a camera selection:
'''Update: Since 03.27.13.Rev.662 firmware''', Periodic Image Sending Enable/Disable switch was replaced by a camera selection:
* Front cameras deselected – periodic image sending is disabled (value 0)
* Front cameras deselected – periodic image sending is disabled (value 0)
* Front camera selected – front camera’s pictures will be sent periodically (value 1)
* Front camera selected – front camera’s pictures will be sent periodically (value 1)
Camera RTC synchronization is done anytime the device itself is synchronized (via NTP, NITZ or GNSS).
Camera RTC synchronization is done anytime the device itself is synchronized (via NTP, NITZ or GNSS).
After 03.27.07.Rev:364 firmware for FMX125 we added a feature to set camera time, same as device selecting time.
After 03.27.13.Rev:662 firmware for FMX125 we added a feature to set camera time, same as device selecting time.
[[File:Zone.jpg|alt=|frameless]]
[[File:Zone.jpg|alt=|frameless]]
Z1 – maximum speed value for DOUT1 if needed.
Z1 – maximum speed value for DOUT1 if needed.
===Crash Detection Functionality using DOUT===
'''The crash detection feature''' is a crucial capability provided by our device. It enhances evidential documentation through video or photo evidence in the event of a crash. However, activating this functionality necessitates a direct connection of the camera to a power source. Nonetheless, such a direct connection can lead to '''battery drainage'''.
To circumvent this issue, we recommend utilizing DOUT and a relay for connection. This setup enables control via SMS or GPRS command, or through predefined scenarios within our device. By activating DOUT post-ignition, the camera receives power, allowing it to function and record evidence even after the ignition is turned off following a crash. '''For your convenience, the connection scheme can be found here: [[DashCam First Start]]'''
'''It is important to note that in the event of a fatal crash where fatalities may occur,''' we cannot guarantee the retrieval of video or photo evidence due to the severity of the accident. Moreover, both the camera and the device itself may sustain irreparable damage in such instances
==Other camera related functionality==
==Other camera related functionality==