Difference between revisions of "ECAN01"

From Wiki Knowledge Base | Teltonika GPS
Line 8: Line 8:
 
*[[FMB640]], [[FMB630]], [[FM6320]], [[FM6300]] to read [https://en.wikipedia.org/wiki/SAE_J1939 J1939] CAN data.
 
*[[FMB640]], [[FMB630]], [[FM6320]], [[FM6300]] to read [https://en.wikipedia.org/wiki/SAE_J1939 J1939] CAN data.
  
It reads can bus data through the isolation of wires without damaging them and forwards signals to tracking device.  
+
It reads can-bus data through the isolation of wires without damaging them and forwards signals to the tracking device.  
 
==Features==
 
==Features==
  
 
*ECAN01 collects vehicle data from CAN bus without damaging the wires
 
*ECAN01 collects vehicle data from CAN bus without damaging the wires
*Powered from on-board power source
+
*Powered from an on-board power source
 
*Reads the signals through the isolation of CAN bus wires
 
*Reads the signals through the isolation of CAN bus wires
 
*Easy to install and operate
 
*Easy to install and operate
Line 76: Line 76:
 
*Dimensions 39.8 x 18 x 16.7 mm
 
*Dimensions 39.8 x 18 x 16.7 mm
 
*CAN-BUS speeds up to 1000 kb/s
 
*CAN-BUS speeds up to 1000 kb/s
*Fuse is protecting device from high current peaks. If voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and current value will increase accordingly.
+
*Fuse is protecting devices from high current peaks. If the voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and the current value will increase accordingly.
  
 
==Pinout==
 
==Pinout==
Line 151: Line 151:
 
==External Links==
 
==External Links==
 
[https://teltonika-gps.com/product/ecan01/ ECAN01 Teltonika]
 
[https://teltonika-gps.com/product/ecan01/ ECAN01 Teltonika]
 +
 +
[[Category:Fleet management]]

Revision as of 13:25, 1 June 2020

Main Page > CAN Trackers & Adapters > ECAN01
ECAN01 TOP.png
ECAN01 BOTTOM.png

ECAN01 is contactless adapter used to read vehicle CAN Bus data. ECAN01 adapter should be used in combination with:

It reads can-bus data through the isolation of wires without damaging them and forwards signals to the tracking device.

Features

  • ECAN01 collects vehicle data from CAN bus without damaging the wires
  • Powered from an on-board power source
  • Reads the signals through the isolation of CAN bus wires
  • Easy to install and operate

Technical features

PARAMETER VALUE
Minimum Typical Typical Maximum Unit
Supply Voltage
Supply Voltage (Recommended Operating Conditions) +10 +12 +24 +30 V
Current Consumption
Working Mode 6.9 mA
Sleep Mode 1.2 mA
Operating Temperature
Operating Temperature -25 +85 °C
Protection
Internal resettable fuse (max 33 V) 750 mA
  • Dimensions 39.8 x 18 x 16.7 mm
  • CAN-BUS speeds up to 1000 kb/s
  • Fuse is protecting devices from high current peaks. If the voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and the current value will increase accordingly.

Pinout

PIN NUMBER PIN NAME

DESCRIPTION

1 CAN L (Blue) Connect to CAN L input of CAN BUS converter
2 CAN H (White/Blue) Connect to CAN H input of CAN BUS converter
3 VCC (RED) Power supply (10-30) V DC (+)
4 GND (-) (Black) Ground wire (10-30) V DC (-)
ECAN01 pinout-01.png

Wiring scheme

ECAN01 wiring scheme.png

Set up ECAN01

  1. Gently open ECAN01 cover using plastic pry tool from both sides
  2. Insert CAN wires as shown in figure 5. Please make sure that correct slots are used (CAN High/CAN Low)
  3. Gently close the device.
  4. Device is ready-to-use.

Gently open ECAN01.pngInsert CAN wires to ECAN01.pngClose ECAN01 cover.pngECAN01 is ready to use.png

ECAN01 Certification & Approvals

Nomenclature, classification codes

FAQ


YouTube

Teltonika CAN adapters Part 1: Introduction
Teltonika CAN adapters Part 2: Installation

External Links

ECAN01 Teltonika