ECAN02: Difference between revisions
No edit summary |
No edit summary |
||
| Line 121: | Line 121: | ||
==ECAN02 Certification & Approvals== | ==ECAN02 Certification & Approvals== | ||
E-Mark is the regulation issued by the Economic Commission for Europe (referred to as ECE). | |||
==Standards applied== | |||
This Approval shall apply to a type of electrical/electronic sub-assemblies (ESA) from serial production under the following conditions: | |||
Individual products from serial production shall comply at least with all requirements set out in the '''Regulation No. 10 R, Amendment 05, Supplement 01''' "Uniform provisions concerning the approval of vehicles with regard to electromagnetic compatibility". | |||
Approval no.: '''E25 R10-06 0044''' | |||
Extension No.: '''00''' | |||
The attached test report and drawings shall be a constituent part of this Approval. | |||
Every product shall be marked with a readable and durable: | |||
- approval marking. | |||
This type of product shall be allotted the following approval marking: | |||
[[File:ECAN01_E-mark.png|cente|250px]] | |||
==Attachments== | |||
<!-- | |||
{| style="margin: 0 auto;valign=" left"" | |||
|[[File:E25 R10-06 0044 (ECAN01)-1.png|thumb|left|x250px|ECAN01 E-mark page 1]] | |||
|[[File:E25 R10-06 0044 (ECAN01)-2.png|thumb|left|x250px|ECAN01 E-mark page 2]] | |||
|[[File:E25 R10-06 0044 (ECAN01)-3.png|thumb|left|x250px|ECAN01 E-mark page 3]] | |||
|} | |||
You can find the PDF version of the certificate '''[[Media:E25 R10-06 0044 (ECAN01).pdf|here]]'''. | |||
{{certification disclaimer}} | |||
==External links== | |||
{{emark links}} | |||
--> | |||
==Nomenclature, classification codes== | ==Nomenclature, classification codes== | ||
Revision as of 15:28, 8 February 2023
Main Page > CAN Trackers & Adapters > ECAN02
ECAN02 is contactless adapter used to read vehicle CAN Bus data. ECAN02 adapter should be used in combination with:
It reads can-bus data through the isolation of wires without damaging them and forwards signals to the tracking device.
Features
- ECAN02 collects vehicle data from CAN bus without damaging the wires
- Powered from an on-board power source
- Reads the signals through the isolation of CAN bus wires
- Easy to install and operate
Technical features
| PARAMETER | VALUE | ||||
|---|---|---|---|---|---|
| Minimum | Typical | Typical | Maximum | Unit | |
| Supply Voltage | |||||
| Supply Voltage (Recommended Operating Conditions) | +10 | +12 | +24 | +30 | V |
| Current Consumption | |||||
| Working Mode | 7.6 | mA | |||
| Sleep Mode | 1.7 | mA | |||
| Operating Temperature | |||||
| Operating Temperature | -25 | +85 | °C | ||
| Protection | |||||
| Internal resettable fuse (max 33 V) | 750 | mA | |||
- Dimensions 39 x 12 x 19 mm
- CAN-BUS speeds up to 1000 kb/s
- Fuse is protecting devices from high current peaks. If the voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and the current value will increase accordingly.
Pinout
| PIN NUMBER | PIN NAME |
DESCRIPTION |
|---|---|---|
| 1 | CAN L | (Blue) Connect to CAN L input of CAN BUS converter |
| 2 | CAN H | (White/Blue) Connect to CAN H input of CAN BUS converter |
| 3 | VCC | (RED) Power supply (10-30) V DC (+) |
| 4 | GND (-) | (Black) Ground wire (10-30) V DC (-) |
Wiring scheme
Set up ECAN02
- Gently open ECAN02 cover using plastic pry tool from both sides
- Glue double-sided adhesive tape to casing inside as shown in figure 2 remove backing material
- Insert CAN wires as shown in figure 3. Please make sure that correct slots are used (CAN High/CAN Low)
- Close the device.
- Device is ready-to-use.
File:Gently open ECAN02.pngFile:Insert CAN wires to ECAN02.pngFile:Close ECAN02 cover.pngFile:ECAN02 is ready to use.png
ECAN02 Certification & Approvals
E-Mark is the regulation issued by the Economic Commission for Europe (referred to as ECE).
Standards applied
This Approval shall apply to a type of electrical/electronic sub-assemblies (ESA) from serial production under the following conditions:
Individual products from serial production shall comply at least with all requirements set out in the Regulation No. 10 R, Amendment 05, Supplement 01 "Uniform provisions concerning the approval of vehicles with regard to electromagnetic compatibility".
Approval no.: E25 R10-06 0044
Extension No.: 00
The attached test report and drawings shall be a constituent part of this Approval.
Every product shall be marked with a readable and durable:
- approval marking.
This type of product shall be allotted the following approval marking:
Attachments
Nomenclature, classification codes
FAQ
- How to install SIMPLE-CAN with LV-CAN200/ALL-CAN300 using:
- FMB110
- FMB120
- FMB122
- FMB125
- FMB110
- FMA120
- FMB630
- FMB640
- FM6300
- FM6320
- FM36M1
- FM3622
- FM3612
Product Change Notifications
ECAN02 Product Change Notifications