ECAN02: Difference between revisions
(Created page with "right|400px right|400px [https://teltonika-gps.com/product/ECAN02/ ECAN02] is contactless adapter used to read vehicle [http...") |
No edit summary |
||
| Line 74: | Line 74: | ||
|} | |} | ||
*Dimensions 39 | *Dimensions 39 x 12 x 19 mm | ||
*CAN-BUS speeds up to 1000 kb/s | *CAN-BUS speeds up to 1000 kb/s | ||
*Fuse is protecting devices from high current peaks. If the voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and the current value will increase accordingly. | *Fuse is protecting devices from high current peaks. If the voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and the current value will increase accordingly. | ||
Revision as of 14:57, 8 February 2023
Main Page > CAN Trackers & Adapters > ECAN02
ECAN02 is contactless adapter used to read vehicle CAN Bus data. ECAN02 adapter should be used in combination with:
It reads can-bus data through the isolation of wires without damaging them and forwards signals to the tracking device.
Features
- ECAN02 collects vehicle data from CAN bus without damaging the wires
- Powered from an on-board power source
- Reads the signals through the isolation of CAN bus wires
- Easy to install and operate
Technical features
| PARAMETER | VALUE | ||||
|---|---|---|---|---|---|
| Minimum | Typical | Typical | Maximum | Unit | |
| Supply Voltage | |||||
| Supply Voltage (Recommended Operating Conditions) | +10 | +12 | +24 | +30 | V |
| Current Consumption | |||||
| Working Mode | 7.6 | mA | |||
| Sleep Mode | 1.7 | mA | |||
| Operating Temperature | |||||
| Operating Temperature | -25 | +85 | °C | ||
| Protection | |||||
| Internal resettable fuse (max 33 V) | 750 | mA | |||
- Dimensions 39 x 12 x 19 mm
- CAN-BUS speeds up to 1000 kb/s
- Fuse is protecting devices from high current peaks. If the voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and the current value will increase accordingly.
Pinout
| PIN NUMBER | PIN NAME |
DESCRIPTION |
|---|---|---|
| 1 | CAN L | (Blue) Connect to CAN L input of CAN BUS converter |
| 2 | CAN H | (White/Blue) Connect to CAN H input of CAN BUS converter |
| 3 | VCC | (RED) Power supply (10-30) V DC (+) |
| 4 | GND (-) | (Black) Ground wire (10-30) V DC (-) |
Wiring scheme
Set up ECAN02
- Gently open ECAN02 cover using plastic pry tool from both sides
- Glue double-sided adhesive tape to casing inside as shown in figure 2 remove backing material
- Insert CAN wires as shown in figure 3. Please make sure that correct slots are used (CAN High/CAN Low)
- Close the device.
- Device is ready-to-use.
File:Gently open ECAN02.pngFile:Insert CAN wires to ECAN02.pngFile:Close ECAN02 cover.pngFile:ECAN02 is ready to use.png
ECAN02 Certification & Approvals
Nomenclature, classification codes
FAQ
- How to install SIMPLE-CAN with LV-CAN200/ALL-CAN300 using:
- FMB110
- FMB120
- FMB122
- FMB125
- FMB110
- FMA120
- FMB630
- FMB640
- FM6300
- FM6320
- FM36M1
- FM3622
- FM3612
Product Change Notifications
ECAN02 Product Change Notifications