FMA120 Parameter list

From Wiki Knowledge Base | Teltonika GPS
Revision as of 08:18, 13 May 2019 by 212.59.13.226 (talk) (Created page with "{{Template:FMA_Device_Family_Parameter_list|BatteryV=Reserved|BatteryCh=Reserved | name = FMA120_Parameter_list}} Category:FMA120 Manual")

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)
Main Page > EOL Products > FMA120 > FMA120 Manual > FMA120 Parameter list


System parameters

Parameter ID Parameter Type Recomended value Value range Value Parameter name
Min Max
1002 Uint8 - 0 2 0 – Ignition Stop Detection Source
1 – Movement sensor
2 – GPS
1003 Uint8 1 0 1 0 – Disable Static navigation
1 – Enable
1004 Uint8 - 0 2 0 – Power voltage Ignition source
1 – Digital input 1
1 – Movement
1005 Uint16 - 0 30000 Voltage Power Voltage High Level
1006 Uint16 - 0 30000 Voltage Power Voltage Low Level
1920 Uint8 - 0 1 0 – Manual Ignition detection (Power voltage)
1 – Auto
1921 Uint8 10 0 65536 Seconds Ignition detection timeout
201 Uint8 1 0 2 0 – after position fix Records Saving/Sending
1 – always
2 – after time sync
202 Uint8 0 0 2 0 – GNSS (all available) GNSS System
1 – GPS only
2 – GLONASS only
1007 Uint32 - 1 259200 Seconds GNSS Fix Timeout
Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1000 Uint8 - 0 2 0 – Disable Sleep settings
1 – Sleep
2 – Deep sleep
200 Uint8 - 1 3000 Minutes Timeout
Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1001 Uint8 - 0 1 0 – 0...10V Analog Input value range
1 – 1...30V
Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1008 Uint8 1 0 1 0 - disabled NTP Time Synchronization
1 – enabled

Records parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1010 Uint8 - 0 1 0 - From oldest Sorting
1 - From Newest
1011 Uint32 - 0 259200 Seconds Active Data Link Timeout
1012 Uint8 - 0 300 Seconds Server Response Timeout
Bw nb.png ATTENTION! Some GSM operators may disconnect the device from an active data link if the device doesn’t send any data for a very long time, even if active data link timeout is set to maximum value. The amount of time that an operator keeps the link open depends solely on the operator. For example, if active data link timeout is set to maximum, 259200 seconds (72 hours), and the device sends data to server every 86400 seconds (24 hours), the operator might disconnect the link earlier and the device will have to connect to the server anew. This may cost extra, depending on the operator GPRS data charge. It is strongly recommended, when using active data link timeout, that data sending to the server should not be very rare (24 hours or more). If data sending is more frequent, then the operator will not disconnect the device form the server.

GSM parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1240 Uint8 - 0 1 0 – Disable GPRS content activation
1 – Enable
1242 Char - 0 32 String APN name
1243 Char - 0 30 String APN username
1244 Char - 0 30 String APN password
Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1245 Char - 0 31 String Domain
1246 Uint16 - 0 65535 Number Target Server Port
1247 Uint8 - 0 1 0 – TCP Protocol
1 – UDP
1248 Uint8 - 0 1 0 – Not Allowed Always online
1 – Allowed
Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1252 Char - 0 5 String SMS Login
1253 Char - 0 5 String SMS password
1250 Char - 0 1 0 - Not Allowed SMS data sending settings
1 - Allowed
1273 Uint32 Example value: 7F,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF - - Time is defined as 19 byte array. First byte of array defines week days; the rest 18 bytes define timestamps with 10 minute interval. In first byte, first bit (LSB) defines if module should connect to GPRS (send SMS) on Monday, second bit – on Tuesday and so on up to seventh bit – which means Sunday. GPRS Week Time
Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1260-1269 Char - 1 digit 16 digits String Authorized phone numbers
150-159 Char - 1 digit 16 digits String SMS Event PreDefined Numbers
1271 X u32 X defines starting position that is changed: If X is from 0 to 49, X means index of operator code which has to be configured. 0 digit 7 digits String Operator list
1272 X u32 X defines starting position that is changed: If X is from 0 to 49, X means index of operator code which has to be configured. 0 digit 7 digits String Operator Black list

Data Acquisition Modes parameters

Home Network GSM operator code "Vehicle on STOP" parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1540 Uint32 - 0 2592000 Seconds Min Period
1543 Uint8 1 1 225 Records Min Saved Records
1544 Uint32 - 0 2592000 Seconds Send period
1545 Uint32 Example value: 7F,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF - - Time is defined as 19 byte array. First byte of array defines week days; the rest 18 bytes define timestamps with 10 minute interval. In first byte, first bit (LSB) defines if module should connect to GPRS (send SMS) on Monday, second bit – on Tuesday and so on up to seventh bit – which means Sunday. GPRS Week Time

Home Network GSM operator code "Vehicle on MOVING" parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1550 Uint32 - 0 2592000 Seconds Min Period
1551 Uint32 - 0 65535 Meters Min distance
1552 Uint16 0 1 160 Angle Min angle
1553 Uint16 1 1 255 Records Min Saved Records
1554 Uint32 - 0 2592000 Seconds Send period
1555 Uint32 Example value: 7F,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF - - Time is defined as 19 byte array. First byte of array defines week days; the rest 18 bytes define timestamps with 10 minute interval. In first byte, first bit (LSB) defines if module should connect to GPRS (send SMS) on Monday, second bit – on Tuesday and so on up to seventh bit – which means Sunday. GPRS Week Time
1556 Uint16 - 0 255 km/h Min Speed
1557 Uint8 - 0 1 0- GPS Min Speed Source
1- LVCAN

Roaming Network GSM operator code "Vehicle on STOP" parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1560 Uint32 - 0 2592000 Seconds Min Period
1563 Uint8 1 1 225 Records Min Saved Records
1564 Uint32 - 0 2592000 Seconds Send period
1565 Uint32 Example value: 7F,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF - - Time is defined as 19 byte array. First byte of array defines week days; the rest 18 bytes define timestamps with 10 minute interval. In first byte, first bit (LSB) defines if module should connect to GPRS (send SMS) on Monday, second bit – on Tuesday and so on up to seventh bit – which means Sunday. GPRS Week Time

Roaming Network GSM operator code "Vehicle on MOVING" parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1570 Uint32 - 0 2592000 Seconds Min Period
1571 Uint32 - 0 65535 Meters Min distance
1572 Uint16 0 1 160 Angle Min angle
1573 Uint16 1 1 255 Records Min Saved Records
1574 Uint32 - 0 2592000 Seconds Send period
1575 Uint32 Example value: 7F,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF - - Time is defined as 19 byte array. First byte of array defines week days; the rest 18 bytes define timestamps with 10 minute interval. In first byte, first bit (LSB) defines if module should connect to GPRS (send SMS) on Monday, second bit – on Tuesday and so on up to seventh bit – which means Sunday. GPRS Week Time
1576 Uint16 - 0 255 km/h Min Speed
1577 Uint8 - 0 1 0- GPS Min Speed Source
1- LVCAN

Unknown Network GSM operator code "Vehicle on STOP" parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1580 Uint32 - 0 2592000 Seconds Min Period
1583 Uint8 1 1 225 Records Min Saved Records
1584 Uint32 - 0 2592000 Seconds Send period
1585 Uint32 Example value: 7F,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF - - Time is defined as 19 byte array. First byte of array defines week days; the rest 18 bytes define timestamps with 10 minute interval. In first byte, first bit (LSB) defines if module should connect to GPRS (send SMS) on Monday, second bit – on Tuesday and so on up to seventh bit – which means Sunday. GPRS Week Time

Unknown Network GSM operator code "Vehicle on MOVING" parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1590 Uint32 - 0 2592000 Seconds Min Period
1591 Uint32 - 0 65535 Meters Min distance
1592 Uint16 0 1 160 Angle Min angle
1593 Uint16 1 1 255 Records Min Saved Records
1594 Uint32 - 0 2592000 Seconds Send period
1595 Uint32 Example value: 7F,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF - - Time is defined as 19 byte array. First byte of array defines week days; the rest 18 bytes define timestamps with 10 minute interval. In first byte, first bit (LSB) defines if module should connect to GPRS (send SMS) on Monday, second bit – on Tuesday and so on up to seventh bit – which means Sunday. GPRS Week Time
1596 Uint16 - 0 255 km/h Min Speed
1597 Uint8 - 0 1 0- GPS Min Speed Source
1- LVCAN

Features parameters

Green driving parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1890 Uint8 - 0 1 0 – Disable Scenario settings
1 – Enable
1891 Uint8 - 0 2 0 - disable Digital Output Control
1 - DOUT1
2 - DOUT2
1909 Uint8 - 0 1 0 - GPS Source
1 - Accelerometer
1892 Float 0.25 0.25 0.85 mG Max Acceleration Force
1893 Float 0.35 0.25 0.85 mG Max Braking Force
1894 Float 0.2 0.1 1.0 mG Max Cornering Force

Overspeeding scenario parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1895 Uint8 0 0 1 0 – Disable Scenario settings
1 – Enable
1896 Uint8 - 0 2 0 – None Digital Output control
1 – DOUT 1
2 – DOUT 2
1897 Uint16 - 0 260 km/h Max speed

Jamming scenario parameters

Parameter ID Parameter Type Recommended Value Value range Value Parameter name
Min Max
1898 Uint8 - 0 1 0 – Disable Scenario settings
1 – Enable
1899 Uint8 - 0 2 0 – None Digital Output control
1 – DOUT1
2 – DOUT2
1900 Uint8 - 0 2 0 – Low sensitivity (50 RSSI) Jamming sensitivity
1 – Medium sensitivity (30 RSSI)
2 – High sensitivity (10 RSSI)
1901 Uint16 60 0 65535 Seconds Jamming Timeout
1902 Uint16 0 0 65535 Seconds Jamming Pulse Duration

Immobilizer scenario parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1903 Uint8 - 0 1 0 – Disable Scenario settings
1 – Enable
1904 Uint8 - 0 2 0 – Disable Digital Output Control
1 – DOUT1
2 – DOUT2
1905 Uint8 - 0 1 0 – Disable iButton list checking
1 – Enable
1906 Uint16 30 5 65353 Seconds Ignition Off Timeout

iButton read notification

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1907 Uint8 - 0 1 0 - Disabled iButton detect
1 - Enabled
1908 Uint8_t 0 0 1 0 - Disabled Digital Output Control
1 - DOUT1
2 - DOUT2

Trip scenario parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1280 Uint8 - 0 1 0 – Disable Scenario settings
1 – Enable
1281 Uint8 - 0 255 km/h Start speed
1282 Uint16 - 0 65535 Seconds Ignition off timeout
1283 Uint8 - 0 1 0 – Not Continuous distance counting
1 – Continuous
1284 Uint8 - 0 1 0 – Disable Remember iButton ID
1 – Enable
1285 Uint8 - 0 - Meters Odometer Value

AutoGeofencing scenario parameters

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1101 Uint8 1 0 1 0 – Disable Scenario Settings
1 – Enable
1102 Uint16 60 0 65535 0 – Disable Activation Timeout
1100 Uint8 - 0 1 0 – Ignition Deactivation Source
1 – Enable
1103 Uint8 1 0 1 0 - Low AutoGeofence event priority
1 - hight
1104 Uint8 2 0 3 0 - No Event AutoGeofence event generating
1 - On entering zone
2 - On exiting zone
3 - On both
1105 Uint32 100 0 1000000 Meters Radius

iButton list

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
3500-3999 Uint64 - 0 FFFFFFFF FFFFFFFF 0 – iButton ID iButton list

Manual Geofence

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1020 Uint32 1000 0 1000000 Border value meters Frame border
1030 Uint8 - 0 1 0 - Circle Shape type
1 - Rectangle
1031 Uint8 - 0 2 0 – Low Priority
1 – High
2 – Panic
1032 Uint8 - 0 3 0 - No event Generate event
1 - On entering zone
2 - On exiting zone
3 - On both
1033 float - -180 180 Rectangle left down corner X coordinate Longitude X1
Or X1 Coordinate circle middle point
1034 float - -90 90 Rectangle left down corner Y1 coordinate latitude Y1
Or Y1 Coordinate circle middle point
1035 float - -180 180 Rectangle right upper corner X2 coordinate longitude X2
1035 float 1000 0 1000000 X2 coordinate radius of circle longitude X2
1036 float - -90 90 Rectangle right upper corner Y2 coordinate latitude Y2
If circle ID 1036 is not used

Similarly to a group defined in the upper table:

Zone number Parameter
Shape Priority Generate event X1 Y1 X2 Radius Y2
1 1030 1031 1032 1033 1034 1035 1035 1036
2 1040 1041 1042 1043 1044 1045 1045 1046
3 1050 1051 1052 1053 1054 1055 1055 1056
4 1060 1061 1062 1063 1064 1065 1065 1066
5 1070 1071 1072 1073 1074 1075 1075 1076



Parameters

ID Parameter name Value type Value description Min Value max Value
1300 I/O#1 property parameter S8 0 - disable 0 1
1 - enable
1301 I/O#1 priority parameter S8 0 - Low 0 2
1 - High
2 - Panic
1302 I/O#1 High level S32 used to set thresholds for I/O properties to generate events. -2147483647 2147483647
1303 I/O#1 Low level S32 used to set thresholds for I/O properties to generate events. -2147483647 2147483647
1304 I/O#1 logic operand S8 0 - on range exit 0 5
1 - on range entrance
2 - both
3 - monitoring
4 - hysteresis
5 - on changes
1305 I/O#1 averaging length S32 Parameter defines I/O property sample length to average 0 2592000

Similarly to a group defined in the upper table

I/O parameters

I/O Element Number I/O element parameters
Digital Input 1 1300-1305
Digital Input 2 1310-1315
Digital Input 3 1320-1325
Analog Input 1 1330-1335
Digital Output 1 1340-1345
Digital Output 2 1350-1355
GNSS PDOP 1360-1365
GNSS HDOP 1370-1375
External Voltage 1380-1385
GNSS Power 1390-1395
Movement Sensor 1400-1405
Trip distance 1410-1415
GSM Operator 1420-1425
Speed (Km/h) 1430-1435
iButton ID 1440-1445
Mode 1450-1455
GSM Signal 1460-1465
Deep Sleep 1470-1475
Cell ID 1480-1485
Area Code 1490-1495
Dallas Temperature 1 1500-1505
Reserved 1510-1515
Reserved 1520-1525
Reserved 1530-1535
Reserved 1110-1115
Ignition 1120-1125
Total Distance 1130-1135
Reserved IO1 1140-1145
Reserved IO2 1150-1155
RFID 1160-1165
LLS Fuel1 1720- 1725
LLS Temp1 1730- 1735
LLS Fuel2 1740- 1745
LLS Temp2 1750- 1755
LLS Fuel3 1760- 1765
LLS Temp3 1770- 1775
LLS Fuel4 1780- 1785
LLS Temp4 1790- 1795
LLS Fuel5 1800- 1805
LLS Temp5 1810- 1815
Dallas Temperature 2 1820- 1825
Dallas Temperature 3 1830- 1835
Dallas Temperature 4 1840- 1845
Dallas Temperature ID 1 1850- 1855
Dallas Temperature ID 2 1860- 1865
Dallas Temperature ID 3 1870- 1875
Dallas Temperature ID 4 1880- 1885

LVCAN

Parameter ID Parameter Type Recommended value Value range Value Parameter name
Min Max
1600 Uint8 0 0 2 0 – Auto detect LVCAN Mode
1 – LV-CAN200
2 – ALL-CAN300
1601 Uint8 1 0 1 0 - Disable Send data with 0, if ignition is off
1 - Enable

Configuration example

Parameter ID Parameter Type Default value Value range Value Parameter name
Min Max
2000 Uint8 - 0 3 0 – Disabled Priority
1 – Low
2 – High
3 – Panic
2001 Uint8 3 0 4 0 - On range exit Generation type
1 - On range entrance
2 - On both
3 - Monitoring
4 - Hysteresis
5 - On change
2002 Uint8 - 0 255 High value High level
2003 Uint8 0 0 255 Low value Low level
2004 Uint8 - 0 265535 value Average constant value

Allowed values

CAN IO Element Minimum value Maximum value
Speed 0 250
Accelerator pedal position 0 100
Total fuel used 0 99999999
Fuel level (liters) 0 100
Engine RPM 0 8200
Vehicle distance 0 2145000000
Fuel level (proc.) 0 100
Program number 0 999

Other CAN settings

Similarly to a group defined in the upper table:

Name Parameter
Priority Generation type Low level High level Avg const'
Vehicle speed 2000 2001 2002 2003 2004
Acceleration Pedal Position 2010 2011 2012 2013 2014
Total fuel used 2020 2021 2022 2023 -
Fuel level (liters) 2030 2031 2032 2033 2034
Engine RPM 2040 2041 2042 2043 2044
Total Mileage 2050 2051 2052 2053 -
Fuel Level (percent) 2060 2061 2062 2063 2064
Program Number 2070 2071 2072 2073 -
Module ID 2080 2081 2082 2083 -
Engine Worktime 2090 2091 2092 2093 -
Engine Worktime (counted) 2100 2101 2102 2103 -
Total Mileage (counted) 2110 2111 2112 2113 -
Fuel Consumed (counted) 2120 2121 2122 2123 -
Fuel Rate 2130 2131 2132 2133 2134
AdBlue Level (percent) 2140 2141 2142 2143 2144
AdBlue Level (liters) 2150 2151 2152 2153 2154
Engine Load 2160 2161 2162 2163 2164
Engine Temperature 2170 2171 2172 2173 2174
Axle 1 Load 2180 2181 2182 2183 2184
Axle 2 Load 2190 2191 2192 2193 2194
Axle 3 Load 2200 2201 2202 2203 2204
Axle 4 Load 2210 2211 2212 2213 2214
Axle 5 Load 2220 2221 2222 2223 2224
Control State Flags 2230 2231 2232 2233 -
Agricultural Machinery Flags 2240 2241 2242 2243 -
Harvesting Time 2250 2251 2252 2253 -
Area of Harvest 2260 2261 2262 2263 -
Mowing Efficiency 2270 2271 2272 2273 2274
Grain Mown Volume 2280 2281 2282 2283 -
Grain Moisture 2290 2291 2292 2293 2294
Harvesting Drum RPM 2300 2301 2302 2303 2304
Gap Under Harvesting Drum 2310 2311 2312 2313 2314
Security State Flags 2320 2321 2322 2323 -
Tachograph Total Vehicle Distance 2330 2331 2332 2333 -
Trip Distance 2340 2341 2342 2343 -
Tachograph Vehicle Speed 2350 2351 2352 2353 2354
Tachograph Driver Card Presence 2360 2361 2362 2363 -
Driver 1 States 2370 2371 2372 2373 -
Driver 2 States 2380 2381 2382 2383 -
Driver 1 Continuous Driving Time 2390 2391 2392 2393 -
Driver 2 Continuous Driving Time 2400 2401 2402 2403 -
Driver 1 Cumulative Break Time 2410 2411 2412 2413 -
Driver 2 Cumulative Break Time 2420 2421 2422 2423 -
Driver 1 Selected Activity Duration 2430 2431 2432 2433 -
Driver 2 Selected Activity Duration 2440 2441 2442 2443 -
Driver 1 Cumulative Driving Time 2450 2451 2452 2453 -
Driver 2 Cumulative Driving Time 2460 2461 2462 2463 -
Driver 1 ID High 2470 2471 2472 2473 -
Driver 1 ID Low 2480 2481 2482 2483 -
Driver 2 ID High 2490 2491 2492 2493 -
Driver 2 ID Low 2500 2501 2502 2503 -
Battery temperature 2510 2511 2512 2513 2514
Battery level 2520 2521 2522 2523 2524
Door Status 2530 2531 2532 2533 -
DTC Faults 2540 2541 2542 2543 -
Slope Of Arm 2550 2551 2552 2553 -
Rotation of Arm 2560 2561 2562 2563 -
Eject of Arm 2570 2571 2572 2573 -
Horizontal Distance Arm Vehicle 2580 2581 2582 2583 -
Height Arm Above Ground 2590 2591 2592 2593 -
Drill RPM 2600 2601 2602 2603 -
Amount of Spread Salt Square Meter 2610 2611 2612 2613 -
Battery Voltage 2620 2621 2622 2623 -
Amount of Spread Fine Grained Salt 2630 2631 2632 2633 -
Amount of Spread Coarse Grained Salt 2640 2641 2642 2643 -
Amount of Spread DiMix 2650 2651 2652 2653 -
Amount of Spread Coarse Grained Calcium 2660 2661 2662 2663 -
Amount of Spread Calcium Chloride 2670 2671 2672 2673 -
Amount of Spread Sodium Chloride 2680 2681 2682 2683 -
Amount of Spread Magnesium Chloride 2690 2691 2692 2693 -
Amount of Spread Gravel 2700 2701 2702 2703 -
Amount of Spread Sand 2710 2711 2712 2713 -
Width Pouring Left 2720 2721 2722 2723 -
Width Pouring Right 2730 2731 2732 2733 -
Salt Spreader Working Hours 2740 2741 2742 2743 -
Distance During Salting 2750 2751 2752 2753 -
Load Weight 2760 2761 2762 2763 -
Retarder Load 2770 2771 2772 2773 -
Cruise Time 2780 2781 2782 2783 -
CNG Status 2790 2791 2792 2793 -
CNG Used 2800 2801 2802 2803 -
CNG Level 2810 2811 2812 2813 -
Oil Level 2820 2821 2822 2823 -
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=FMA120_Parameter_list&oldid=35393"