FMA120 General description
From Wiki Knowledge Base | Teltonika GPS
Revision as of 10:55, 23 August 2018 by Marek.rakalovic (talk | contribs)
Main Page > EOL Products > FMA120 > FMA120 Manual > FMA120 General description
FMA120 is a tracking terminal with GNSS and GSM connectivity, which is able to collect device coordinates and transfer them via GSM network to a server. This device is perfectly suitable for applications, which require the location acquirement of remote objects.
Technical features
| Part name | Physical specification |
|---|---|
| Navigation indication | LED |
| Modem indication | LED |
| Socket 2x5 | Tyco Micro MATE-N-LOK™ 4-794628-0 or similar |
| USB | Mini USB socket |
| GNSS | Internal GNSS antenna |
| GSM | Internal GSM antenna |
| Technical details | |
|---|---|
| 2 W max. Current consumption at 12 V |
GPRS: average 120 mA rms Nominal: average 65 mA rms GNSS sleep: average 28 mA Deep Sleep: average 5 mA² |
| Battery charge current | Average 115 mA |
| Operating temperature (without battery) | -40°C..+85 °C |
| Operating temperature (without battery) | -40°C..+85 °C |
| Storage relative humidity | 5..95% (no condensation) |
| Internal fuse | 3A, 125V |
Dimension drawing:
Technical information about internal battery
| Internal back-up battery | Battery voltage (V) | Nominal Capacity (mAh) | Power (Wh) | Charge temperature (°C) | Discharge temperature (°C) | Storage temperature (°C) |
|---|---|---|---|---|---|---|
| Li-ion rechargeable battery | 3.75～3.90 | 170 | 0.64 – 0.66 | 0 to +45 | -20 to +60 | -20 to +45 for 1 month -20 to +35 for 6 months |
Batteries are covered by 6 month warranty support.
 |
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. |
 |
Battery should not be disposed of into general household waste. Bring damaged or worn-out batteries to your local recycling center or dispose them into a battery recycle bin commonly found in supermarkets. |
Electrical characteristics
| Characteristic description | Value | |||
|---|---|---|---|---|
| Min. | Typ. | Max. | Unit | |
| Supply Voltage: | ||||
| Supply Voltage (Recommended Operating Conditions) | 5 | 30 | V | |
| Digital Input: | ||||
| Input resistance (DIN1) | 120 | kOhm | ||
| Input resistance (DIN2, DIN3) | 15 | kOhm | ||
| Input Voltage (Recommended Operating Conditions) | 0 | Supply voltage | V | |
| Input Voltage threshold (DIN1) | 7.5 | V | ||
| Input Voltage threshold (DIN2, DIN3) | 2.6 | V | ||
| Digital Output (Open Drain grade): | ||||
| Drain Current (Digital Output OFF) | 120 | uA | ||
| Drain Current (Digital Output ON, Recommended Operating Conditions) | 300 | mA | ||
| Static Drain-Source Resistance (Digital Output ON) | 300 | mOhm | ||
| Analog Input: | ||||
| Input voltage (Recommended Operating Conditions), Range 1 | 0 | 10 | V | |
| Input resistance, Range 1 | 120 | kOhm | ||
| Measurement error | 4.4 | % | ||
| Additional error | ±26 | mV | ||
| Input Voltage (Recommended Operating Conditions) Range2 | 0 | 30 | V | |
| Input resistance, Range2 | 146.7 | kOhm | ||
| Measurement error | 4 | % | ||
| Additional error | ±40 | mV | ||
| Output Supply Voltage 1-Wire:³ | ||||
| Supply voltage | 3.3 | 3.6 | V | |
| Output inner resistance | 10 | Ohm | ||
| Output current (Uout > 3.0 V) | 30 | mA | ||
| Short circuit current (Uout = 0) | 130 | mA | ||
|
|
Analog Input error margin can increase if temperature varies. If Analog input is not connected FMA1YX will still measure certain numbers and it cannot be 0. This measurement is influenced by hardware components. |
Absolute Maximum Ratings
| Characteristic description | Value | |||
|---|---|---|---|---|
| Min. | Typ. | Max. | Unit | |
| Supply Voltage (Absolute Maximum Ratings) | -32 | 32 | V | |
| Drain-Source clamp threshold voltage (Absolute Maximum Ratings), (Idrain = 2mA) | 36 | V | ||
| Digital Input Voltage (Absolute Maximum Ratings) | -32 | 32 | V | |
| Analog Input Voltage (Absolute Maximum Ratings) | -32 | 32 | V | |
