Difference between revisions of "FMB641 CAN \ Tachograph"
m |
m (Protected "FMB641 CAN \ Tachograph" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))) |
||
| (One intermediate revision by one other user not shown) | |||
| Line 6: | Line 6: | ||
* FMB641 CAN1 connected to vehicle's FMS(J1939) BUS line<br> | * FMB641 CAN1 connected to vehicle's FMS(J1939) BUS line<br> | ||
| − | * FMB641 CAN2 connected to vehicle's Tachograph - Instructions can be found on [[ | + | * FMB641 CAN2 connected to vehicle's Tachograph - Instructions can be found on [[FMB640_and_Tachograph_Solution|FMB640 and Tachograph Solution]] wiki page; |
==Tachograph Settings== | ==Tachograph Settings== | ||
| Line 19: | Line 19: | ||
[[image:FMB640_Tachograph_settings2.gif]] | [[image:FMB640_Tachograph_settings2.gif]] | ||
| − | FMB641 can be wired to Tachograph using instructions provided in [[ | + | FMB641 can be wired to Tachograph using instructions provided in [[FMB640_and_Tachograph_Solution|FMB640 and Tachograph Solution]] wiki page. |
'''Alternative DDD download''' | '''Alternative DDD download''' | ||
| Line 49: | Line 49: | ||
[[image:FMB640_FMS_settings.gif]] | [[image:FMB640_FMS_settings.gif]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
[[Category:FMB641 Configuration]] | [[Category:FMB641 Configuration]] | ||
Revision as of 15:42, 4 March 2022
Main Page > EOL Products > FMB641 > FMB641 Configuration > FMB641 CAN \ TachographCAN \ Tachograph
CAN \ Tachograph are used to configure device when connection of CAN1 and CAN2 BUS lines are performed.
Teltonika recommendations:
- FMB641 CAN1 connected to vehicle's FMS(J1939) BUS line
- FMB641 CAN2 connected to vehicle's Tachograph - Instructions can be found on FMB640 and Tachograph Solution wiki page;
Tachograph Settings
In FMB641 configurator “CAN/Tachograph” section tachograph settings should be set in order to download files.
DDD download source – to which CAN line tachograph is connected;
Tachograph ignition source – which DIN is connected to vehicle ignition ("Ignition" parameter - tachograph ignition source will be the same as configured in "System" -> "Ignition Source");
FMB641 can be wired to Tachograph using instructions provided in FMB640 and Tachograph Solution wiki page.
Alternative DDD download
Enables the possibility to download specific DDD driver and co-driver card data from non-original locations. It may include last download information.
NOTE: Alternative DDD download WILL NOT work with GEN2 Tachographs (VDO 4.0 or Stoneridge SE5000 8.0)
By default, this parameter is DISABLED.
WEB Tacho Settings
WEB Tacho Settings are used to configure Tacho WEB server to which device periodically connects.
WEB Tacho Settings:
Status - functionality enabling;
Domain – server domain where files will be send;
Port – server port where files will be send;
Start delay – delay after turning on ignition to start procedure of file sending.
FMS settings
FMS settings is used to configure FMS source.
If you have FMS wired to FMB641 CAN1, FMS source should be selected as CAN1.
If you have FMS wired to FMB641 CAN2, FMS source should be selected as CAN2.
