Template talk:FMB CAN adapters: Difference between revisions

From Teltonika Telematics Wiki
 
(7 intermediate revisions by 3 users not shown)
Line 1: Line 1:
Easy steps to install and configure following CAN adapters on {{{model|FMC125}}} device:
* [[LV-CAN200]]
* [[ALL-CAN300]]
* [[CAN-CONTROL]]
* [[SIMPLE-CAN]]
* [[MINI-CAN]]
__TOC__
==Installing CAN adapter with {{{model|FMC125}}} device==
===Installing LV-CAN200/ALL-CAN300/CAN-CONTROL===
You can watch [[LV-CAN200]]/[[ALL-CAN300]] installation video in our YouTube channel [https://youtu.be/V9RTdSy1E8w '''here'''] or follow connection instructions below.
====Tools needed for installation====
* [[LV-CAN200]]/[[ALL-CAN300]]/[[CAN-CONTROL]]
* Connection scheme (Please contact Teltonika Sales Representative and provide information about '''vehicle manufacturer''', '''model''' and '''year'''.
* {{{model|FMC125}}} device
* Pliers
* Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)
* Plastic pry tool
* Zip ties
====Installation steps====
# Be ready with a vehicle '''connection scheme''' that you have received from a Teltonika Sales Representative.
# '''Check the scheme''' for the current vehicle connection. Look for connectors matching '''PINs numbers''' and colors (may be different) according to connection scheme.
# Connect CAN adapter with {{{model|FMC125}}}:
## Connect CAN adapter <span style="color:#0000eb;">'''PIN 6'''</span> '''(Rx)''' to <span style='color:white;text-decoration:line-through'><span style="color:#0000eb;">'''INPUT 6'''</span></span> of {{{model|FMC125}}}.
## Connect CAN adapter <span style="color:#d8d800;">'''PIN 5'''</span> '''(Tx)''' to <span style='color:white;text-decoration:line-through'><span style="color:#d8d800;">'''INPUT 5'''</span></span> of {{{model|FMC125}}}.
# Connect CAN adapter '''CAN wires (CAN L, CAN H)''' as specified in connection scheme.<p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>Do not swap CAN L and CAN H lines.<br />Not all CAN adapter wires may be used in vehicle.</b></td></table></p>
# Connect CAN adapter '''positive''' and '''ground''' wires to the vehicle power supply lines or near {{{model|FMC125}}} power wires.<p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>Do not swap power supply lines.<br />Make sure that voltage does not exceed 30V.</b></td></table></p>
# Switch vehicle '''ignition to ACC''' position. CAN adapter '''LED diode''' on the back should start '''blinking'''.
# Configure CAN adapter to read CAN bus data or control vehicle by setting its '''program number''' - [[{{{model|FMC125}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]
<br />
[[File:CAN_adapter_connection_example_updated.png|1000px|none|thumb|LV-CAN200/ALL-CAN300 connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.]]
[[File:Can-control_connection_example_updated.png|1000px|none|thumb|CAN-CONTROL connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.]]
<br />
===Installing LV-CAN200/ALL-CAN300 + SIMPLE-CAN===
----
You can watch [[LV-CAN200]]/[[ALL-CAN300]] + [[SIMPLE-CAN]] installation video in our YouTube channel [https://youtu.be/V9RTdSy1E8w?t=356 '''here'''] or follow connection instructions below.
====Tools needed for installation====
* [[LV-CAN200]]/[[ALL-CAN300]]
* Connection scheme (Please contact Teltonika Sales Representative and provide information about '''vehicle manufacturer''', '''model''' and '''year'''.
* [[SIMPLE-CAN]] (Used for contactless connection. If '''two CAN lines''' need to be connected, '''two SIMPLE-CAN's''' must be used.)
* {{{model|FMC125}}} device
* Pliers
* Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)
* Plastic pry tool
* Zip ties
====Installation steps====
# Follow the same '''1, 2, 3''' installation steps as with [[{{{model|FMC125}}}_CAN_adapters#Installation_steps| LV-CAN200/ALL-CAN300/CAN-CONTROL installation]].
# Connect the appropiate CAN bus pair of wires between CAN adapter and [[SIMPLE-CAN]]:
#: If '''CAN1 line''' need to be connected as specified in connection scheme:
## Connect CAN adapter <span style="color:brown;">'''CAN1 L'''</span> to <span style="color:brown;">'''CAN L'''</span> of [[SIMPLE-CAN]].
## Connect CAN adapter <span style='color:white;text-decoration:line-through'><span style="color:brown;">'''CAN1 H'''</span></span> to <span style='color:white;text-decoration:line-through'><span style="color:brown;">'''CAN H'''</span></span> of [[SIMPLE-CAN]].
#: If '''CAN2 line''' need to be connected as specified in connection scheme:
## Connect CAN adapter <span style="color:green;">'''CAN2 L'''</span> to <span style="color:brown;">'''CAN L'''</span> of [[SIMPLE-CAN]].
## Connect CAN adapter <span style='color:white;text-decoration:line-through'><span style="color:green;">'''CAN2 H'''</span></span> to <span style='color:white;text-decoration:line-through'><span style="color:brown;">'''CAN H'''</span></span> of [[SIMPLE-CAN]].<p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>Do not swap CAN L and CAN H lines.<br />Not all CAN adapter wires may be used in vehicle.</b></td></table></p>
# Fasten [[SIMPLE-CAN]] '''between vehicle CAN bus wires''' according to the connection scheme. '''It doeasn't matter which wire is on which side.'''<p>[[File:SIMPLE-CAN_connection.gif|none]]</p>
# Connect CAN adapter '''positive''' and '''ground''' wires to the vehicle power supply lines or near {{{model|FMC125}}} power wires.<p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>Do not swap power supply lines.<br />Make sure that voltage does not exceed 30V.</b></td></table></p>
# Switch vehicle '''ignition to ACC''' position.
# [[SIMPLE-CAN]] '''LED will shine continously''' so device awaits for '''calibration'''.<div><ul><li style="display: inline-block;">[[File:SIMPLE-CAN_calibration.gif|none|thumb|'''Press the switch shortly''' and wait for the LED to start blinking '''every one second'''.<br /><br /><br />]]</li><li style="display: inline-block;">[[File:SIMPLE-CAN after calibration.gif|none|thumb|Automatic calibration process takes up to 10 seconds depending on the vehicle model. Device is calibrated properly then the LED is blinking '''every 2 seconds'''.]]</li></ul></div><p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.</b></td></table></p>
# Configure CAN adapter to read CAN bus data by setting its '''program number''' - [[{{{model|FMC125}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]
<br />
[[File:Can_adapter%2Bsimple-can_connection_example_updated.png|1000px|none|thumb|LV-CAN200/ALL-CAN300 + SIMPLE-CAN connection example. This is not a connection diagram for your vehicle. Follow LV-CAN200/ALL-CAN300 connection scheme suitable for your vehicle.]]
<br />
==CAN Adapter Configuration==
===CAN Adapter program number selection===
----
CAN Adapter must be set to program number which depends on the vehicle model. '''Needed program number is always written on CAN Adapter mounting scheme.''' In order to be able to enter program number in adapter '''Software date of CAN adapter must be newer than connection scheme date'''.
CAN adapter Software date can be checked:
* Via [[{{{model|FMC125}}}_Status_info#CAN_Adapter_Info|Teltonika Configurator→Status→CAN Adapter]]
* Via SMS command - [[FMB_lvcangetinfo|lvcangetinfo]]
The number of digits required to enter correct Program No. may vary depending on the Software and manufacture date of your CAN Adapter:
* [[LV-CAN200#Adapter_changes|LV-CAN200 adapter changes]]
* [[ALL-CAN300#Adapter_changes|ALL-CAN300 adapter changes]]
====Entering via SMS command====
----
Required conditions:
* CAN adapter properly connected to {{{model|FMC125}}} device
CAN adapter program number can be set remotely, using SMS command.
Send following '''SMS command''' to {{{model|FMC125}}} device:
* If you have set SMS login and password: <code>login pass lvcansetprog X</code>
* If SMS login and password are not set leave two spaces before command: <code>&nbsp;&nbsp;lvcansetprog X</code>
Command example: <code>&nbsp;&nbsp;lvcansetprog 11434</code><br />
SMS response: <code>LVCAN ProgNum: 11434</code>
If during SMS command {{{model|FMC125}}} was in following Sleep mode:
* [[{{{model|FMC125}}}_Sleep_modes#GPS_Sleep_mode|GPS Sleep]] - Program No. will be set immediately.
* [[{{{model|FMC125}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep]] - Program No. will be set after device wake up.
* [[{{{model|FMC125}}}_Sleep_modes#Online_Deep_Sleep_mode|Online Deep Sleep]] - Program No. will be set immediately.
* [[{{{model|FMC125}}}_Sleep_modes#Ultra_Deep_Sleep_mode|Ultra Deep Sleep]] - Program No. will be set after device wake up.
====Entering via Teltonika Configurator====
----
Required conditions:
* CAN adapter properly connected to {{{model|FMC125}}} device
CAN adapter program number can be set via '''[[Teltonika Configurator]] → (1) CAN Adapter → (2) Program Number'''. When program number is entered press [[File:Save_to_device.png|25px|link=]] '''(3) Save to device''' button that saves the entered program number into {{{model|FMC125}}}.
<br/><br/>
[[Image:Can adapter conf.png|700px]]
<br/><br/>
====Entering manually====
----
Required conditions:
* CAN adapter properly connected to {{{model|FMC125}}} device
* Vehicle ignition must be ON
Depending on used CAN Adapter, length of setup sequence will vary.
Steps to set program number:
[[Image:Fmb120_adapter_led.png|300px|right|thumb|LV-CAN200, ALL-CAN300 back]][[File:Can_control_back-2.png|300px|right|thumb|CAN-CONTROL back]]
{| class="wikitable" style="width:70%;"
|+
|-
| rowspan="5" style="border: 1px solid #0054A6; background: white; color: #0054A6; text-align: center; width:10%;" | For<br/>ALL-CAN300<br/>LV-CAN200<br/>3 digit
| rowspan="6" style="border: 1px solid #0054A6; background: white; color: #0054A6; text-align: center; width:10%;" | For<br/>ALL-CAN300<br/>LV-CAN200<br/>4 digit
| rowspan="7" style="border: 1px solid #0054A6; background: white; color: #0054A6; text-align: center; width:11%;" | For<br/>LV-CAN200<br/>CAN-CONTROL<br/>5 digit
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white; width:38%;" |1. Hold SWITCH down until LED stars blinking.
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |2. Release the SWITCH.
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |3. Then LED starts blinking and counting first digit of program number (one blink means digit 1, two blinks mean digit 2 etc). To stop counter, push SWITCH.
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |4. Release the SWITCH, then LED starts blinking and counting second digit of program number. To stop counter, push SWITCH.
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |5. Release the SWITCH, then LED starts blinking and counting third digit on program number. To stop counter, push SWITCH.
|-
| rowspan="2" style="border: 1px solid white; border-bottom: 1px solid #0054A6; background: white;" |
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |6. Release the SWITCH, then LED starts blinking and counting fourth digit on program number. To stop counter, push SWITCH.
|-
| style="border: 1px solid white; border-bottom: 1px solid #0054A6; background: white;" |
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |7. Release the SWITCH, then LED starts blinking and counting fifth digit on program number. To stop counter, push SWITCH.
|-
| colspan="3" style="border: 1px solid #0054A6; background: white; color: #0054A6; text-align: center;" | All Devices
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |8. Release SWITCH, if programming is successful LED will blink 10 times.
|}
==={{{model|FMC125}}} CAN Adapter parameters configuration===
----
====Teltonika Configurator====
CAN Adapter configuration can be performed using [[Teltonika Configurator]] via '''Micro-USB cable''' or '''Bluetooth connection''' when CAN Adapter is connected to the vehicle.<br/>
When {{{model|FMC125}}} is connected to the CAN Adapter, user can see all information that is received from the vehicle in [[Teltonika Configurator]]''' → Status → CAN Adapter''' tab or [[Teltonika Configurator]]''' → CAN Adapter''' section. In '''Status → CAN Adapter''' tab you can see information about CAN adapter and its readable parameters. In '''CAN Adapter''' section you can configure CAN Adapter and see incoming CAN bus data highlighted by <span style="color:green;">'''green'''</span> background color. Incoming data in both sections is automatically refreshed every 5 seconds. CAN bus data which should be readable from your vehicle is provided in "CAN Adapter supported vehicles list", which you can get from Teltonika Sales Representative.<br/>
The CAN Adapter I/O element can be configured like any other I/O element in [[Teltonika Configurator]]. All information about I/O element parameters description is in section [[{{{model|FMC125}}} I/O settings|I/O settings]].
<br />
[[Image:Fmb120_can_conf_example.png|800px|none]]
<br />
When using offline configuration method user can select which CAN data (according to vehicle) will be sent directly to the server without connection to adapter.
=====Send data with 0, if ignition is off=====
----
Depending on CAN Adapter I/O parameters and ignition status, {{{model|FMC125}}} can send locked (last known) CAN Adapter I/O and active (real time) parameters values or reset values to 0. When ignition is off, CAN Adapter I/O parameters values sent to server are:
{| class="wikitable" style="width:40%;"
|+
! style="width: 25%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"  | CAN Adapter I/O element
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"  | Status
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Vehicle Speed
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Accelerator pedal position
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Total fuel used
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Fuel level (liters)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Engine RPM
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Total mileage
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Fuel level (%)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Program number
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Module ID
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Engine Work Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Engine Work Time (counted)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Total Mileage (counted)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Fuel Consumed (counted)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Fuel Rate
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Program number
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | AdBlue Level (%)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | AdBlue Level (liters)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Engine Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Engine Temperature
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Axle 1 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Axle 2 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Axle 3 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Axle 4 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Axle 5 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Control State Flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Agricultural Machinery Flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Harvesting Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Area of Harvest
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Mowing Efficiency
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Grain Mown Volume
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Grain Moisture
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Harvesting Drum RPM
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Gap Under Harvesting Drum
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Security State Flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Tachograph Total Vehicle Distance
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Trip Distance
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Tachograph Vehicle Speed
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Tachograph Driver Card Presence
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver1 States
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver2 States
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver1 Continuous Driving Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver2 Continuous Driving Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver1 Cumulative Break Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver2 Cumulative Break Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver1 Selected Activity Duration
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver2 Selected Activity Duration
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver1 Cumulative Driving Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | Driver2 Cumulative Driving Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"  | active
|-
|}
<br />
====SMS Configuration====
----
All CAN Adapter IO elements can be configured remotely via SMS commands.
=====SMS/GPRS Commands=====
CAN Adapters have several dedicated SMS/GPRS commands.<br />
SMS command structure:
<SMS login><space><SMS password><space><command><space><value>
SMS command [[FMB lvcangetinfo|lvcangetinfo]] example:
* If you have set SMS login and password: <code>login pass lvcangetinfo</code>
* If SMS login and password are not set leave two spaces before command: <code><span style="color:#f8f9fa">aa</span>lvcangetinfo</code>
<br />
GPRS commands require [[Codec 12]] protocol.
For more SMS commands please see [[{{{model|FMC125}}} SMS/GPRS command list|SMS/GPRS command list]]
{| class="wikitable" style="width:80%;"
|+
! style="width: 25%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | COMMAND
! style="width: 65%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | DESCRIPTION
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | RESPONSE
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcansetprog #
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Set program number to CAN Adapter that is connected to {{{model|FMC125}}}.<br/># - three digit number that identity vehicle.
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcansimpletacho #
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Add or remove simpletacho start byte.<br/> # - 0 or 1 (0 – don’t add start byte, 1 – add start byte).
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | No
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcangetprog
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Get program number from CAN Adapter that is connected to {{{model|FMC125}}}.
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[FMB lvcangetinfo|lvcangetinfo]]
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Get information about connected CAN Adapter
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[FMB_lvcanclear|lvcanclear #]]
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Clear Total Mileage (counted), Engine Work Time (counted), Fuel Consumed (counted) parameters values.<br/> # - parameter (0 – Engine work time (counted), 1 – Fuel Consumed (counted), 2 – Vehicle Mileage (counted)).
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | allcanmode
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Turn on ALL-CAN300 mode.
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanmode
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Turn on LV-CAN200 mode.
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[FMB_lvcanfaultcodes|lvcanfaultcodes]]
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Read DTC fault codes
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| colspan="3" style="border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | '''CAN-CONTROL specific commands'''
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanopenalldoors
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Open [unlock] all doors
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanclosealldoors
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Close [lock] all doors
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanopentrunk
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Open [unlock] trunk
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanturninglights
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | One flash of all turn lights ordered trough accidental / blinking turn light switch
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
<!-- | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanwindowsopen:#
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | open windows # sec. (one sending of command will cause the windows to continue opening for xx seconds). #: [1,3,5...25,27,29]
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanwindowsclose:#
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | close windows # sec. (one sending of command will cause thewindows to continue closing for xx seconds). #: [1,3,5...25,27,29]
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
-->
|}
===CAN Adapter software update Over The Air===
The software of CAN adapters [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] can now be updated Over The Air by using [[FOTA WEB]]. The feature is also supported by our fresh [[FMB140]] device which has a built-in CAN bus reading adapter. Upgrading the software of a CAN adapter will add more program numbers, thus, more vehicle models will be supported.
<b>Please note</b>, that only newer version of LV-CAN200 and ALL-CAN300 CAN adapters support this feature. The version of CAN adapter can be checked by sending an SMS command [[FMB_lvcangetinfo|lvcangetinfo]]. If, in the response message, <b>"SWRev:"</b> is <b>145</b>, the CAN adapter is older and if it is <b>245</b>, the adapter is newer. It does not apply to CAN-CONTROL - all CAN-CONTROL adapters support firmware updates over the air.
In order to update your device‘s firmware please follow a quick and simple step-by-step guide which is below. The procedure is the same for all devices.
*FMC125 device, which is connected to the CAN adapter (or [[FMB140]] which has internal CAN adapter), must be registered in Fota Web – device‘s model, firmware version, serial number and other information must be shown.
*A correct firmware version must be uploaded to the FMC125 device. Currently this feature is only supported with firmware version 03.25.11.Rev144. Once device with correct firmware version connects to Fota Web on the next scheduled connection (or instant connection, initiated by an SMS command "web_connect"), a small, blue, „CAN“ logo will appear next to the device‘s model:
[[Image:111I registered.jpg|1160x1160px|center]]
<br />
*A current version of the CAN adapter version can be checked by pressing a small „i“ button on the right of fleet management device details. All FMC125 device‘s and CAN adapter‘s details are listed in one window:
[[Image:z111FM OldDate.jpg|1162x1162px|center]]
<br />
*If the software is not up-to-date it can be updated in the main window. A check-box needs to be ticked, then „Actions“ button pressed and „Update CAN adapter firmware“ selected:
[[File:z111FMB120 + LV-CAN200 Fota details in progress.jpg|alt=|center|1159x1159px]]
<br />
*Once the software update task has been assigned, it can be seen in the main window. Please note, that uploading will start after the next scheduled connection to Fota Web (or instant connection, initiated by an SMS command "web_connect"):
[[Image:111FM Assigned.jpg|1155x1155px|center]]
<br />
*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to Fota Web (or instant connection, initiated by an SMS command "web_connect"):
[[Image:z111FM Done.jpg|1162x1162px|center]]
<br />
===CAN Adapter State Flags===
----
CAN Adapters receive data about the states of various systems within the vehicle, and send them as flags to {{{model|FMC125}}}. {{{model|FMC125}}} device stores these flags in hexadecimal format, as one variable. Bellow is a list of kept flags and how to retrieve them.<br /> The full list of state flags is stored only by:
* [[ALL-CAN300]]
Only '''security state flags''' and '''control state flags''' are stored by:
* [[CAN-CONTROL]]
{| class="wikitable" style="width:70%;"
|+
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | Property name
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | Size, bytes
! style="width: 40%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | Value bitmasks
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| Control state flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 4
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Byte0 (LSB):<br/>
<span style=color:#FF6600>0x01</span> – STOP<br/>
<span style=color:#FF6600>0x02</span> – Oil pressure / level<br/>
<span style=color:#FF6600>0x04</span> – Coolant liquid temperature / level<br/>
<span style=color:#FF6600>0x08</span> – Handbrake system<br/>
<span style=color:#FF6600>0x10</span> – Battery not charging<br/>
<span style=color:#FF6600>0x20</span> – AIRBAG<br/>
<span style=color:#FF6600>0x40</span> – EPS (Electric power steering)<br/>
<span style=color:#FF6600>0x80</span> – ESP (Electronic Stability Program)<br/><br>
Byte1:<br/>
<span style=color:#0000FF>0x01</span> – CHECK ENGINE<br/>
<span style=color:#0000FF>0x02</span> – Lights failure<br/>
<span style=color:#0000FF>0x04</span> – Low tire pressure<br/>
<span style=color:#0000FF>0x08</span> – Wear of brake pads<br/>
<span style=color:#0000FF>0x10</span> – Warning<br/>
<span style=color:#0000FF>0x20</span> – ABS<br/>
<span style=color:#0000FF>0x40</span> – Low Fuel<br/>
<span style=color:#0000FF>0x80</span> – Maintenance required<br/><br/>
Byte2:<br/>
<span style=color:#339A6C>0x01</span> – ESP<br/>
<span style=color:#339A6C>0x02</span> – Glow plug indicator<br/>
<span style=color:#339A6C>0x04</span> – FAP<br/>
<span style=color:#339A6C>0x08</span> – Electronics pressure control<br/>
<span style=color:#339A6C>0x10</span> – Parking lights<br/>
<span style=color:#339A6C>0x20</span> – Dipped headlights<br/>
<span style=color:#339A6C>0x40</span> – Full beam headlights<br/>
<span style=color:#339A6C>0x80</span> – Front foglights<br/><br/>
Byte3:<br/>
<span style=color:#9A3300>0x01</span> – Ready to drive<br/>
<span style=color:#9A3300>0x02</span> – Cruise control<br/>
<span style=color:#9A3300>0x04</span> – Automatic Retarder<br/>
<span style=color:#9A3300>0x08</span> – Manual retarder<br/>
<span style=color:#9A3300>0x10</span> – Air Conditioning<br/>
<span style=color:#9A3300>0x20</span> – Rear foglights<br/>
<span style=color:#9A3300>0x40</span> – Passenger's seat belt<br/>
<span style=color:#9A3300>0x80</span> – Driver's seat belt<br/>
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Agricultural machinery flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 8
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| Byte0 (LSB):<br/>
<span style=color:#FF6600>0x01</span> – Mowing<br/>
<span style=color:#FF6600>0x02</span> – Grain release from hopper<br/>
<span style=color:#FF6600>0x04</span> – First front hydraulic turned on<br/>
<span style=color:#FF6600>0x08</span> – Rear Power Take-Off turned on<br/><br/>
Byte1:<br/><span style=color:#0000FF>0x01</span> – Excessive play under the threshing drum<br/>
<span style=color:#0000FF>0x02</span> – Grain tank is open<br/>
<span style=color:#0000FF>0x04</span> – 100% of Grain tank<br/>
<span style=color:#0000FF>0x08</span> – 70% of Grain tank<br/>
<span style=color:#0000FF>0x10</span> – Drain filter in hydraulic system of drive cylinders is plugged<br/>
<span style=color:#0000FF>0x20</span> – Pressure filter of drive cylinders hydraulic system is plugged<br/>
<span style=color:#0000FF>0x40</span> – Alarm oil level in oil tank<br/>
<span style=color:#0000FF>0x80</span> – Pressure filter of brakes hydraulic system is plugged<br/><br/>
Byte2:<br/><span style=color:#339A6C>0x01</span> – Oil filter of engine is plugged<br/>
<span style=color:#339A6C>0x02</span> – Fuel filter is plugged<br/>
<span style=color:#339A6C>0x04</span> – Air filter is plugged<br/>
<span style=color:#339A6C>0x08</span> – Alarm oil temperature in hydraulic system of chassis<br/>
<span style=color:#339A6C>0x10</span> – Alarm oil temperature in hydraulic system of drive cylinders<br/>
<span style=color:#339A6C>0x20</span> – Alarm oil pressure in engine<br/>
<span style=color:#339A6C>0x40</span> – Alarm coolant level<br/>
<span style=color:#339A6C>0x80</span> – Overflow chamber of hydraulic unit<br/><br/>
Byte3:<br/><span style=color:#9A3300>0x01</span> – Unloader drive is ON. Unloading tube pivot is in idle position<br/>
<span style=color:#9A3300>0x02</span> – No operator!<br/>
<span style=color:#9A3300>0x04</span> – Straw walker is plugged<br/>
<span style=color:#9A3300>0x08</span> – Water in fuel<br/>
<span style=color:#9A3300>0x10</span> – Cleaning fan RPM<br/>
<span style=color:#9A3300>0x20</span> – Trashing drum RPM<br/>
<span style=color:#9A3300>0x40</span> – Pouring chemicals turned on<br/>
<span style=color:#9A3300>0x80</span> – Conveyor belt turned on<br/><br/>
Byte4:<br/>
<span style=color:#FF00FF>0x01</span> – Salt spreaders drive wheel turned on<br/>
<span style=color:#FF00FF>0x02</span> – Low water level in the tank<br/>
<span style=color:#FF00FF>0x04</span> – First rear hydraulic turned on<br/>
<span style=color:#FF00FF>0x08</span> – Standalone engine working<br/>
<span style=color:#FF00FF>0x10</span> – Right joystick moved right<br/>
<span style=color:#FF00FF>0x20</span> – Right joystick moved left<br/>
<span style=color:#FF00FF>0x40</span> – Right joystick moved front<br/>
<span style=color:#FF00FF>0x80</span> – Right joystick moved back<br/>
<br/>
Byte5:<br/>
<span style=color:#339A6C>0x01</span> – Brushes turned on<br/>
<span style=color:#339A6C>0x02</span> – Water supply turned on<br/>
<span style=color:#339A6C>0x04</span> – Vacuum cleaner<br/>
<span style=color:#339A6C>0x08</span> – Unloading from the hopper<br/>
<span style=color:#339A6C>0x10</span> – High Pressure washer (Karcher)<br/>
<span style=color:#339A6C>0x20</span> – Salt (sand) disperser ON<br/>
<span style=color:#339A6C>0x40</span> – Low salt (sand) level<br/><br/>
Byte6:<br/>
<span style=color:#66D6AD>0x01</span> – Second front hydraulic turned on<br/>
<span style=color:#66D6AD>0x02</span> – Third front hydraulic turned on<br/>
<span style=color:#66D6AD>0x04</span> – Fourth front hydraulic turned on<br/>
<span style=color:#66D6AD>0x08</span> – Second rear hydraulic turned on<br/>
<span style=color:#66D6AD>0x10</span> – Third rear hydraulic turned on<br/>
<span style=color:#66D6AD>0x20</span> – Fourth rear hydraulic turned on<br/>
<span style=color:#66D6AD>0x40</span> – Front three-point Hitch turned on<br/>
<span style=color:#66D6AD>0x80</span> – Rear three-point Hitch turned on<br/><br/>
Byte7:<br/><span style=color:#00331A>0x01</span> – Left joystick moved right<br/>
<span style=color:#00331A>0x02</span> – Left joystick moved left<br/>
<span style=color:#00331A>0x04</span> – Left joystick moved front<br/>
<span style=color:#00331A>0x08</span> – Left joystick moved back<br/>
<span style=color:#00331A>0x10</span> – Front Power Take-Off turned on<br/>
<span style=color:#00331A>0x20</span> – Liquid pump turned on<br/>
<span style=color:#00331A>0x40</span> – Light signal turned on<br/>
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| Security state flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| 8
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| Byte0 (LSB):<br/>
<span style=color:#008181>0x01</span> – CAN1 connected, but currently module not received data<br/>
<span style=color:#008181>0x02</span> – CAN1 not connected, require connection<br/>
<span style=color:#008181>0x03</span> – CAN1 connected<br/>
<span style=color:#008181>0x04</span> – CAN2 connected, but currently module not received data<br/>
<span style=color:#008181>0x08</span> – CAN2 not connected, require connection<br/>
<span style=color:#008181>0x0C</span> – CAN2 connected<br/>
<span style=color:#008181>0x10</span> – CAN3 connected, but currently module not received data<br/>
<span style=color:#008181>0x20</span> – CAN3 not connected, require connection<br/>
<span style=color:#008181>0x30</span> – CAN3 connected<br/><br/>
Byte2:<br/>
<span style=color:#339A6C>0x04</span> – Battery charging<br/>
<span style=color:#339A6C>0x08</span> – Charging cable connected<br/>
<span style=color:#339A6C>0x10</span> – Vehicle working mode, 1- business mode, 0 - private mode<br/>
<span style=color:#339A6C>0x20</span> – Bit appears when any operate button in car was put. This bit is reset if the button is released<br/>
<span style=color:#339A6C>0x40</span> – Bit appears when immobilizer is in service mode<br/>
<span style=color:#339A6C>0x80</span> – Immobiliser, bit appears during introduction of a programmed sequence of keys in the car<br/><br/>
Byte3:<br/>
<span style=color:#0000FF>0x01</span> – The key is in ignition lock<br/>
<span style=color:#0000FF>0x02</span> – Ignition on<br/>
<span style=color:#0000FF>0x04</span> – Dynamic ignition on<br/>
<span style=color:#0000FF>0x08</span> – Webasto<br/>
<span style=color:#0000FF>0x10</span> – Car closed<br/>
<span style=color:#0000FF>0x20</span> – Car closed by factory's remote control<br/>
<span style=color:#0000FF>0x40</span> – Factory-installed alarm system is actuated (is in panic mode)<br/>
<span style=color:#0000FF>0x80</span> – Factory-installed alarm system is emulated by module<br/><br/>
Byte4:<br/>
<span style=color:#9DCD00>0x01</span> – Parking activated (automatic gearbox)<br/>
<span style=color:#9DCD00>0x10</span> – Handbrake is actuated (information available only with ignition on)<br/>
<span style=color:#9DCD00>0x20</span> – Footbrake is actuated (information available only with ignition on)<br/>
<span style=color:#9DCD00>0x40</span> – Engine is working (information available only when the ignition on)<br/>
<span style=color:#9DCD00>0x80</span> – Reverse is on<br/><br/>
Byte5:<br/>
<span style=color:#339A6C>0x01</span> – Front left door opened<br/>
<span style=color:#339A6C>0x02</span> – Front right door opened<br/>
<span style=color:#339A6C>0x04</span> – Rear left door opened<br/>
<span style=color:#339A6C>0x08</span> – Rear right door opened<br/>
<span style=color:#339A6C>0x10</span> – Engine cover opened<br/>
<span style=color:#339A6C>0x20</span> – Trunk door opened<br/><br/>
Byte6:<br/>
&ndash; Low nibble (mask 0x0F value)<br/>
<span style=color:#66D6AD>0x01</span> – Car was closed by the factory's remote control<br/>
<span style=color:#66D6AD>0x02</span> – Car was opened by the factory's remote control<br/>
<span style=color:#66D6AD>0x03</span> – Trunk cover was opened by the factory's remote control<br/>
<span style=color:#66D6AD>0x04</span> – Module has sent a rearming signal<br/>
<span style=color:#66D6AD>0x05</span> – Car was closed three times by the factory's remote control<br/>
&ndash; High nibble (mask 0xF0 bit)<br/>
<span style=color:#66D6AD>0x80</span> – CAN module goes to sleep mode<br/>
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Tachograph driver card presence
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| 1
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| <span style=color:#9A3300>0x00</span> – No driver card<br/>
<span style=color:#9A3300>0x01</span> – Driver1 card presence<br/>
<span style=color:#9A3300>0x02</span> – Driver2 card presence<br/>
<span style=color:#9A3300>0x03</span> – Driver1 and driver2 cards present<br/>
|-
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver 1 states
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 1
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" rowspan=2 | <span style=color:#124806>0xX0</span> – Break/rest<br/>
<span style=color:#124806>0xX1</span> – Availability<br/>
<span style=color:#124806>0xX2</span> – Work<br/>
<span style=color:#124806>0xX3</span> – Driving<br/>
<span style=color:#124806>0x0X</span> – No time-related warning detected<br/>
<span style=color:#124806>0x1X</span> – Limit #1: 15 min before 4 1/2 h<br/>
<span style=color:#124806>0x2X</span> – Limit #2: 4 1/2 h reached (continuous driving time exceeded)<br/>
<span style=color:#124806>0x3X</span> – Limit #3: 15 minutes before optional warning 1<br/>
<span style=color:#124806>0x4X</span> – Limit #4: optional warning 1 reached<br/>
<span style=color:#124806>0x5X</span> – Limit #5: 15 min before optional warning<br/>
<span style=color:#124806>0x6X</span> – Limit #6: optional warning 2 reached<br/>
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver 2 states
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 1
|}
<br/><br/>
==LV-CAN200/ALL-CAN300 Important Information==
===Program Number logic change===
Due to the growing number of supported cars, program numbers have exceeded "999". In order to maintain one number format, we are moving from 3-digit to 4-digit program numbers.<br/>In new LV-CAN200/ALL-CAN300 firmware (from 2017-09-01) all program numbers that were up to 999 are changed to start from 1000. So that further program numbers would continue the counting with 4-digit numbers.<br/>However, all existing program numbers stay the same, but "1" is added to the front. Device still understands the entered 3-digit program number (via SMS/GPRS), it will automatically add "1" before it. If you enter "247" - device number will turn into "1247". In Bootloader only 4-digit format is available, just add "1" to the front of the needed program number.
===Example===
When using older connection schemes where program number displayed as 3-digit program number:
[[Image:Fmb120_can_prog_number.png|600px|none]]
Using LV-CAN200/ALL-CAN300 Bootloader from soft version 2017-09-27 it is necessary to add "1" to the front of program number:
[[Image:Fmb120_can_updater.png|400px|none]]
<!--
==SIMPLE-CAN - contactless CAN-BUS reader==
[[Image:Fmb120_simplecan.png|300px|right]]
SIMPLE-CAN is a contactless adapter used to read vehicle CAN data with LV-CAN200 or ALL-CAN300. If LV-CAN200 or ALL-CAN300 connection requires two CAN lines to get all data, then two SIMPLE-CAN readers are required.
<font size="+1">Technical details</font>
* Power supply voltage +9..+63 V.
* Power supply current: standby 1.6 mA, active 8.3 mA @ 12 V; standby 0.91 mA, active 4.3 mA @ 24 V.
* CAN-BUS speeds from 33.33 to 500 kb/s.
* Automatically sets CAN Low, CAN High polarity.
* Automatically adjusts signal level and speed.<br/><br/>
SIMPLE-CAN works in the '''listening mode only''', so that not all the data available on the CAN-BUS may be received using this solution. '''The device automatically sets CAN L/H polarity''', but the calibration has to be always performed during installation process. Connection of previously calibrated unit to another car needs new calibration because the reader '''automatically adjusts signal level and speed''' to different CAN buses. The device also '''automatically adapts''' to the found '''noise level'''.
[[Image:Fmb120_simplecan_pinout.png|800px|none]]
When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. <br/>'''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON.
*Please press the switch briefly and wait for the LED to start blinking every second.
* Automatic calibration process takes up to 10 seconds depending on the vehicle's model.
*Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active).
*When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine.
*If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.-->
== FMC CAN adapters_FMC130 ==
Easy steps to install and configure following CAN adapters on {{{model|FMC130}}} device:
Easy steps to install and configure following CAN adapters on {{{model|FMC130}}} device:
* [[LV-CAN200]]
* [[LV-CAN200]]
Line 982: Line 321:
* If SMS login and password are not set leave two spaces before command: <code><span style="color:#f8f9fa">aa</span>lvcangetinfo</code>
* If SMS login and password are not set leave two spaces before command: <code><span style="color:#f8f9fa">aa</span>lvcangetinfo</code>
<br />
<br />
GPRS commands require [[Codec 12]] protocol.
GPRS commands require [[Codec#Codec_12|Codec 12]] protocol.


For more SMS commands please see [[{{{model|FMC130}}} SMS/GPRS command list|SMS/GPRS command list]]
For more SMS commands please see [[{{{model}}} SMS/GPRS command list|SMS/GPRS command list]]


{| class="wikitable" style="width:80%;"
{| class="wikitable" style="width:80%;"
Line 1,059: Line 398:
In order to update your device‘s firmware please follow a quick and simple step-by-step guide which is below. The procedure is the same for all devices.
In order to update your device‘s firmware please follow a quick and simple step-by-step guide which is below. The procedure is the same for all devices.


*FMC130 device, which is connected to the CAN adapter (or [[FMB140]] which has internal CAN adapter), must be registered in Fota Web – device‘s model, firmware version, serial number and other information must be shown.
*FMC130 device, which is connected to the CAN adapter (or [[FMB140]] which has internal CAN adapter), must be registered in FOTA WEB – device‘s model, firmware version, serial number and other information must be shown.


*A correct firmware version must be uploaded to the FMC130 device. Currently this feature is only supported with firmware version 03.25.11.Rev144. Once device with correct firmware version connects to Fota Web on the next scheduled connection (or instant connection, initiated by an SMS command "web_connect"), a small, blue, „CAN“ logo will appear next to the device‘s model:
*A correct firmware version must be uploaded to the [[FMC130]] device. Currently this feature is only supported with firmware version 03.25.11.Rev144. Once device with correct firmware version connects to FOTA WEB on the next scheduled connection (or instant connection, initiated by an SMS command "web_connect"), a small, blue, „CAN“ logo will appear next to the device‘s model:


[[Image:111I registered.jpg|1160x1160px|center]]
[[Image:111I registered.jpg|1160x1160px|center]]
Line 1,073: Line 412:
*If the software is not up-to-date it can be updated in the main window. A check-box needs to be ticked, then „Actions“ button pressed and „Update CAN adapter firmware“ selected:
*If the software is not up-to-date it can be updated in the main window. A check-box needs to be ticked, then „Actions“ button pressed and „Update CAN adapter firmware“ selected:


[[File:z111FMB120 + LV-CAN200 Fota details in progress.jpg|alt=|center|1159x1159px]]
[[File:Fota_3.png|alt=|center|1159x1159px]]
<br />
<br />


*Once the software update task has been assigned, it can be seen in the main window. Please note, that uploading will start after the next scheduled connection to Fota Web (or instant connection, initiated by an SMS command "web_connect"):
*Once the software update task has been assigned, it can be seen in the main window. Please note, that uploading will start after the next scheduled connection to FOTA WEB(or instant connection, initiated by an SMS command "web_connect"):


[[Image:111FM Assigned.jpg|1155x1155px|center]]
[[Image:111FM Assigned.jpg|1155x1155px|center]]
<br />
<br />


*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to Fota Web (or instant connection, initiated by an SMS command "web_connect"):
*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB(or instant connection, initiated by an SMS command "web_connect"):


[[Image:z111FM Done.jpg|1162x1162px|center]]
[[Image:z111FM Done.jpg|1162x1162px|center]]

Latest revision as of 14:37, 4 July 2022

Easy steps to install and configure following CAN adapters on FMC130 device:

Installing CAN adapter with FMC130 device

Installing LV-CAN200/ALL-CAN300/CAN-CONTROL

You can watch LV-CAN200/ALL-CAN300 installation video in our YouTube channel here or follow connection instructions below.

Tools needed for installation

  • LV-CAN200/ALL-CAN300/CAN-CONTROL
  • Connection scheme (Please contact Teltonika Sales Representative and provide information about vehicle manufacturer, model and year.
  • FMC130 device
  • Pliers
  • Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)
  • Plastic pry tool
  • Zip ties

Installation steps

  1. Be ready with a vehicle connection scheme that you have received from a Teltonika Sales Representative.
  2. Check the scheme for the current vehicle connection. Look for connectors matching PINs numbers and colors (may be different) according to connection scheme.
  3. Connect CAN adapter with FMC130:
    1. Connect CAN adapter PIN 6 (Rx) to INPUT 6 of FMC130.
    2. Connect CAN adapter PIN 5 (Tx) to INPUT 5 of FMC130.
  4. Connect CAN adapter CAN wires (CAN L, CAN H) as specified in connection scheme.

    Do not swap CAN L and CAN H lines.
    Not all CAN adapter wires may be used in vehicle.

  5. Connect CAN adapter positive and ground wires to the vehicle power supply lines or near FMC130 power wires.

    Do not swap power supply lines.
    Make sure that voltage does not exceed 30V.

  6. Switch vehicle ignition to ACC position. CAN adapter LED diode on the back should start blinking.
  7. Configure CAN adapter to read CAN bus data or control vehicle by setting its program number - CAN Adapter configuration


LV-CAN200/ALL-CAN300 connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.
CAN-CONTROL connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.


Installing LV-CAN200/ALL-CAN300 + SIMPLE-CAN


You can watch LV-CAN200/ALL-CAN300 + SIMPLE-CAN installation video in our YouTube channel here or follow connection instructions below.

Tools needed for installation

  • LV-CAN200/ALL-CAN300
  • Connection scheme (Please contact Teltonika Sales Representative and provide information about vehicle manufacturer, model and year.
  • SIMPLE-CAN (Used for contactless connection. If two CAN lines need to be connected, two SIMPLE-CAN's must be used.)
  • FMC130 device
  • Pliers
  • Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)
  • Plastic pry tool
  • Zip ties

Installation steps

  1. Follow the same 1, 2, 3 installation steps as with LV-CAN200/ALL-CAN300/CAN-CONTROL installation.
  2. Connect the appropiate CAN bus pair of wires between CAN adapter and SIMPLE-CAN:
    If CAN1 line need to be connected as specified in connection scheme:
    1. Connect CAN adapter CAN1 L to CAN L of SIMPLE-CAN.
    2. Connect CAN adapter CAN1 H to CAN H of SIMPLE-CAN.
    If CAN2 line need to be connected as specified in connection scheme:
    1. Connect CAN adapter CAN2 L to CAN L of SIMPLE-CAN.
    2. Connect CAN adapter CAN2 H to CAN H of SIMPLE-CAN.

      Do not swap CAN L and CAN H lines.
      Not all CAN adapter wires may be used in vehicle.

  3. Fasten SIMPLE-CAN between vehicle CAN bus wires according to the connection scheme. It doeasn't matter which wire is on which side.

  4. Connect CAN adapter positive and ground wires to the vehicle power supply lines or near FMC130 power wires.

    Do not swap power supply lines.
    Make sure that voltage does not exceed 30V.

  5. Switch vehicle ignition to ACC position.
  6. SIMPLE-CAN LED will shine continously so device awaits for calibration.
    • Press the switch shortly and wait for the LED to start blinking every one second.


    • Automatic calibration process takes up to 10 seconds depending on the vehicle model. Device is calibrated properly then the LED is blinking every 2 seconds.

    If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

  7. Configure CAN adapter to read CAN bus data by setting its program number - CAN Adapter configuration


LV-CAN200/ALL-CAN300 + SIMPLE-CAN connection example. This is not a connection diagram for your vehicle. Follow LV-CAN200/ALL-CAN300 connection scheme suitable for your vehicle.


CAN Adapter Configuration

CAN Adapter program number selection


CAN Adapter must be set to program number which depends on the vehicle model. Needed program number is always written on CAN Adapter mounting scheme. In order to be able to enter program number in adapter Software date of CAN adapter must be newer than connection scheme date. CAN adapter Software date can be checked:

The number of digits required to enter correct Program No. may vary depending on the Software and manufacture date of your CAN Adapter:

Entering via SMS command


Required conditions:

  • CAN adapter properly connected to FMC130 device

CAN adapter program number can be set remotely, using SMS command. Send following SMS command to FMC130 device:

  • If you have set SMS login and password: login pass lvcansetprog X
  • If SMS login and password are not set leave two spaces before command:   lvcansetprog X

Command example:   lvcansetprog 11434
SMS response: LVCAN ProgNum: 11434

If during SMS command FMC130 was in following Sleep mode:

Entering via Teltonika Configurator


Required conditions:

  • CAN adapter properly connected to FMC130 device

CAN adapter program number can be set via Teltonika Configurator → (1) CAN Adapter → (2) Program Number. When program number is entered press (3) Save to device button that saves the entered program number into FMC130.



Entering manually


Required conditions:

  • CAN adapter properly connected to FMC130 device
  • Vehicle ignition must be ON

Depending on used CAN Adapter, length of setup sequence will vary.

Steps to set program number:

LV-CAN200, ALL-CAN300 back
CAN-CONTROL back
For
ALL-CAN300
LV-CAN200
3 digit
For
ALL-CAN300
LV-CAN200
4 digit
For
LV-CAN200
CAN-CONTROL
5 digit
1. Hold SWITCH down until LED stars blinking.
2. Release the SWITCH.
3. Then LED starts blinking and counting first digit of program number (one blink means digit 1, two blinks mean digit 2 etc). To stop counter, push SWITCH.
4. Release the SWITCH, then LED starts blinking and counting second digit of program number. To stop counter, push SWITCH.
5. Release the SWITCH, then LED starts blinking and counting third digit on program number. To stop counter, push SWITCH.
6. Release the SWITCH, then LED starts blinking and counting fourth digit on program number. To stop counter, push SWITCH.
7. Release the SWITCH, then LED starts blinking and counting fifth digit on program number. To stop counter, push SWITCH.
All Devices 8. Release SWITCH, if programming is successful LED will blink 10 times.

FMC130 CAN Adapter parameters configuration


Teltonika Configurator

CAN Adapter configuration can be performed using Teltonika Configurator via Micro-USB cable or Bluetooth connection when CAN Adapter is connected to the vehicle.
When FMC130 is connected to the CAN Adapter, user can see all information that is received from the vehicle in Teltonika Configurator → Status → CAN Adapter tab or Teltonika Configurator → CAN Adapter section. In Status → CAN Adapter tab you can see information about CAN adapter and its readable parameters. In CAN Adapter section you can configure CAN Adapter and see incoming CAN bus data highlighted by green background color. Incoming data in both sections is automatically refreshed every 5 seconds. CAN bus data which should be readable from your vehicle is provided in "CAN Adapter supported vehicles list", which you can get from Teltonika Sales Representative.
The CAN Adapter I/O element can be configured like any other I/O element in Teltonika Configurator. All information about I/O element parameters description is in section I/O settings.


When using offline configuration method user can select which CAN data (according to vehicle) will be sent directly to the server without connection to adapter.

Send data with 0, if ignition is off

Depending on CAN Adapter I/O parameters and ignition status, FMC130 can send locked (last known) CAN Adapter I/O and active (real time) parameters values or reset values to 0. When ignition is off, CAN Adapter I/O parameters values sent to server are:

CAN Adapter I/O element Status
Vehicle Speed reset
Accelerator pedal position reset
Total fuel used lock
Fuel level (liters) lock
Engine RPM reset
Total mileage lock
Fuel level (%) lock
Program number lock
Module ID lock
Engine Work Time lock
Engine Work Time (counted) lock
Total Mileage (counted) lock
Fuel Consumed (counted) lock
Fuel Rate reset
Program number lock
AdBlue Level (%) lock
AdBlue Level (liters) lock
Engine Load reset
Engine Temperature active
Axle 1 Load lock
Axle 2 Load lock
Axle 3 Load lock
Axle 4 Load lock
Axle 5 Load lock
Control State Flags active
Agricultural Machinery Flags active
Harvesting Time lock
Area of Harvest reset
Mowing Efficiency active
Grain Mown Volume active
Grain Moisture active
Harvesting Drum RPM reset
Gap Under Harvesting Drum active
Security State Flags active
Tachograph Total Vehicle Distance lock
Trip Distance reset
Tachograph Vehicle Speed reset
Tachograph Driver Card Presence active
Driver1 States active
Driver2 States active
Driver1 Continuous Driving Time active
Driver2 Continuous Driving Time active
Driver1 Cumulative Break Time active
Driver2 Cumulative Break Time active
Driver1 Selected Activity Duration active
Driver2 Selected Activity Duration active
Driver1 Cumulative Driving Time active
Driver2 Cumulative Driving Time active


SMS Configuration


All CAN Adapter IO elements can be configured remotely via SMS commands.

SMS/GPRS Commands

CAN Adapters have several dedicated SMS/GPRS commands.
SMS command structure:

<SMS login><space><SMS password><space><command><space><value>

SMS command lvcangetinfo example:

  • If you have set SMS login and password: login pass lvcangetinfo
  • If SMS login and password are not set leave two spaces before command: aalvcangetinfo


GPRS commands require Codec 12 protocol.

For more SMS commands please see [[{{{model}}} SMS/GPRS command list|SMS/GPRS command list]]

COMMAND DESCRIPTION RESPONSE
lvcansetprog # Set program number to CAN Adapter that is connected to FMC130.
# - three digit number that identity vehicle.
Yes
lvcansimpletacho # Add or remove simpletacho start byte.
# - 0 or 1 (0 – don’t add start byte, 1 – add start byte).
No
lvcangetprog Get program number from CAN Adapter that is connected to FMC130. Yes
lvcangetinfo Get information about connected CAN Adapter Yes
lvcanclear # Clear Total Mileage (counted), Engine Work Time (counted), Fuel Consumed (counted) parameters values.
# - parameter (0 – Engine work time (counted), 1 – Fuel Consumed (counted), 2 – Vehicle Mileage (counted)).
Yes
allcanmode Turn on ALL-CAN300 mode. Yes
lvcanmode Turn on LV-CAN200 mode. Yes
lvcanfaultcodes Read DTC fault codes Yes
CAN-CONTROL specific commands
lvcanopenalldoors Open [unlock] all doors Yes
lvcanclosealldoors Close [lock] all doors Yes
lvcanopentrunk Open [unlock] trunk Yes
lvcanturninglights One flash of all turn lights ordered trough accidental / blinking turn light switch Yes

CAN Adapter software update Over The Air

The software of CAN adapters LV-CAN200, ALL-CAN300 and CAN-CONTROL can now be updated Over The Air by using FOTA WEB. The feature is also supported by our fresh FMB140 device which has a built-in CAN bus reading adapter. Upgrading the software of a CAN adapter will add more program numbers, thus, more vehicle models will be supported.

Please note, that only newer version of LV-CAN200 and ALL-CAN300 CAN adapters support this feature. The version of CAN adapter can be checked by sending an SMS command lvcangetinfo. If, in the response message, "SWRev:" is 145, the CAN adapter is older and if it is 245, the adapter is newer. It does not apply to CAN-CONTROL - all CAN-CONTROL adapters support firmware updates over the air.

In order to update your device‘s firmware please follow a quick and simple step-by-step guide which is below. The procedure is the same for all devices.

  • FMC130 device, which is connected to the CAN adapter (or FMB140 which has internal CAN adapter), must be registered in FOTA WEB – device‘s model, firmware version, serial number and other information must be shown.
  • A correct firmware version must be uploaded to the FMC130 device. Currently this feature is only supported with firmware version 03.25.11.Rev144. Once device with correct firmware version connects to FOTA WEB on the next scheduled connection (or instant connection, initiated by an SMS command "web_connect"), a small, blue, „CAN“ logo will appear next to the device‘s model:


  • A current version of the CAN adapter version can be checked by pressing a small „i“ button on the right of fleet management device details. All FMC130 device‘s and CAN adapter‘s details are listed in one window:


  • If the software is not up-to-date it can be updated in the main window. A check-box needs to be ticked, then „Actions“ button pressed and „Update CAN adapter firmware“ selected:


  • Once the software update task has been assigned, it can be seen in the main window. Please note, that uploading will start after the next scheduled connection to FOTA WEB(or instant connection, initiated by an SMS command "web_connect"):


  • When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB(or instant connection, initiated by an SMS command "web_connect"):


CAN Adapter State Flags


CAN Adapters receive data about the states of various systems within the vehicle, and send them as flags to FMC130. FMC130 device stores these flags in hexadecimal format, as one variable. Bellow is a list of kept flags and how to retrieve them.
The full list of state flags is stored only by:

Only security state flags and control state flags are stored by:

Property name Size, bytes Value bitmasks
Control state flags 4 Byte0 (LSB):

0x01 – STOP
0x02 – Oil pressure / level
0x04 – Coolant liquid temperature / level
0x08 – Handbrake system
0x10 – Battery not charging
0x20 – AIRBAG
0x40 – EPS (Electric power steering)
0x80 – ESP (Electronic Stability Program)

Byte1:
0x01 – CHECK ENGINE
0x02 – Lights failure
0x04 – Low tire pressure
0x08 – Wear of brake pads
0x10 – Warning
0x20 – ABS
0x40 – Low Fuel
0x80 – Maintenance required

Byte2:
0x01 – ESP
0x02 – Glow plug indicator
0x04 – FAP
0x08 – Electronics pressure control
0x10 – Parking lights
0x20 – Dipped headlights
0x40 – Full beam headlights
0x80 – Front foglights

Byte3:
0x01 – Ready to drive
0x02 – Cruise control
0x04 – Automatic Retarder
0x08 – Manual retarder
0x10 – Air Conditioning
0x20 – Rear foglights
0x40 – Passenger's seat belt
0x80 – Driver's seat belt

Agricultural machinery flags 8 Byte0 (LSB):

0x01 – Mowing
0x02 – Grain release from hopper
0x04 – First front hydraulic turned on
0x08 – Rear Power Take-Off turned on

Byte1:
0x01 – Excessive play under the threshing drum
0x02 – Grain tank is open
0x04 – 100% of Grain tank
0x08 – 70% of Grain tank
0x10 – Drain filter in hydraulic system of drive cylinders is plugged
0x20 – Pressure filter of drive cylinders hydraulic system is plugged
0x40 – Alarm oil level in oil tank
0x80 – Pressure filter of brakes hydraulic system is plugged

Byte2:
0x01 – Oil filter of engine is plugged
0x02 – Fuel filter is plugged
0x04 – Air filter is plugged
0x08 – Alarm oil temperature in hydraulic system of chassis
0x10 – Alarm oil temperature in hydraulic system of drive cylinders
0x20 – Alarm oil pressure in engine
0x40 – Alarm coolant level
0x80 – Overflow chamber of hydraulic unit

Byte3:
0x01 – Unloader drive is ON. Unloading tube pivot is in idle position
0x02 – No operator!
0x04 – Straw walker is plugged
0x08 – Water in fuel
0x10 – Cleaning fan RPM
0x20 – Trashing drum RPM
0x40 – Pouring chemicals turned on
0x80 – Conveyor belt turned on

Byte4:
0x01 – Salt spreaders drive wheel turned on
0x02 – Low water level in the tank
0x04 – First rear hydraulic turned on
0x08 – Standalone engine working
0x10 – Right joystick moved right
0x20 – Right joystick moved left
0x40 – Right joystick moved front
0x80 – Right joystick moved back

Byte5:
0x01 – Brushes turned on
0x02 – Water supply turned on
0x04 – Vacuum cleaner
0x08 – Unloading from the hopper
0x10 – High Pressure washer (Karcher)
0x20 – Salt (sand) disperser ON
0x40 – Low salt (sand) level

Byte6:
0x01 – Second front hydraulic turned on
0x02 – Third front hydraulic turned on
0x04 – Fourth front hydraulic turned on
0x08 – Second rear hydraulic turned on
0x10 – Third rear hydraulic turned on
0x20 – Fourth rear hydraulic turned on
0x40 – Front three-point Hitch turned on
0x80 – Rear three-point Hitch turned on

Byte7:
0x01 – Left joystick moved right
0x02 – Left joystick moved left
0x04 – Left joystick moved front
0x08 – Left joystick moved back
0x10 – Front Power Take-Off turned on
0x20 – Liquid pump turned on
0x40 – Light signal turned on

Security state flags 8 Byte0 (LSB):

0x01 – CAN1 connected, but currently module not received data
0x02 – CAN1 not connected, require connection
0x03 – CAN1 connected
0x04 – CAN2 connected, but currently module not received data
0x08 – CAN2 not connected, require connection
0x0C – CAN2 connected
0x10 – CAN3 connected, but currently module not received data
0x20 – CAN3 not connected, require connection
0x30 – CAN3 connected

Byte2:
0x04 – Battery charging
0x08 – Charging cable connected
0x10 – Vehicle working mode, 1- business mode, 0 - private mode
0x20 – Bit appears when any operate button in car was put. This bit is reset if the button is released
0x40 – Bit appears when immobilizer is in service mode
0x80 – Immobiliser, bit appears during introduction of a programmed sequence of keys in the car

Byte3:
0x01 – The key is in ignition lock
0x02 – Ignition on
0x04 – Dynamic ignition on
0x08 – Webasto
0x10 – Car closed
0x20 – Car closed by factory's remote control
0x40 – Factory-installed alarm system is actuated (is in panic mode)
0x80 – Factory-installed alarm system is emulated by module

Byte4:
0x01 – Parking activated (automatic gearbox)
0x10 – Handbrake is actuated (information available only with ignition on)
0x20 – Footbrake is actuated (information available only with ignition on)
0x40 – Engine is working (information available only when the ignition on)
0x80 – Reverse is on

Byte5:
0x01 – Front left door opened
0x02 – Front right door opened
0x04 – Rear left door opened
0x08 – Rear right door opened
0x10 – Engine cover opened
0x20 – Trunk door opened

Byte6:
– Low nibble (mask 0x0F value)
0x01 – Car was closed by the factory's remote control
0x02 – Car was opened by the factory's remote control
0x03 – Trunk cover was opened by the factory's remote control
0x04 – Module has sent a rearming signal
0x05 – Car was closed three times by the factory's remote control
– High nibble (mask 0xF0 bit)
0x80 – CAN module goes to sleep mode

Tachograph driver card presence 1 0x00 – No driver card

0x01 – Driver1 card presence
0x02 – Driver2 card presence
0x03 – Driver1 and driver2 cards present

Driver 1 states 1 0xX0 – Break/rest

0xX1 – Availability
0xX2 – Work
0xX3 – Driving
0x0X – No time-related warning detected
0x1X – Limit #1: 15 min before 4 1/2 h
0x2X – Limit #2: 4 1/2 h reached (continuous driving time exceeded)
0x3X – Limit #3: 15 minutes before optional warning 1
0x4X – Limit #4: optional warning 1 reached
0x5X – Limit #5: 15 min before optional warning
0x6X – Limit #6: optional warning 2 reached

Driver 2 states 1



LV-CAN200/ALL-CAN300 Important Information

Program Number logic change

Due to the growing number of supported cars, program numbers have exceeded "999". In order to maintain one number format, we are moving from 3-digit to 4-digit program numbers.
In new LV-CAN200/ALL-CAN300 firmware (from 2017-09-01) all program numbers that were up to 999 are changed to start from 1000. So that further program numbers would continue the counting with 4-digit numbers.
However, all existing program numbers stay the same, but "1" is added to the front. Device still understands the entered 3-digit program number (via SMS/GPRS), it will automatically add "1" before it. If you enter "247" - device number will turn into "1247". In Bootloader only 4-digit format is available, just add "1" to the front of the needed program number.

Example

When using older connection schemes where program number displayed as 3-digit program number:

Using LV-CAN200/ALL-CAN300 Bootloader from soft version 2017-09-27 it is necessary to add "1" to the front of program number: