Difference between revisions of "ADAS Configuration"

From Wiki Knowledge Base | Teltonika GPS
(32 intermediate revisions by 4 users not shown)
Line 1: Line 1:
−
__TOC__
+
==ADAS configuration==
 +
{| class="wikitable"
 +
| colspan="2" |'''You can adjust  the LDW Sensitivity for your convenience'''
 +
|-
 +
|
 +
* Enable LDW function. (On  / Off)
 +
 
 +
* Set the Activation Speed  (15, 30, 45, 60, 75km/h).
 +
* Set the sensitivity of  LDW warning on a scale of 1 to 5.
 +
* As the level gets higher,  it gets more sensitive.
 +
* Enable Repeat LDW (On /  Off)
 +
* If it’s on, ADAS keeps  warning until the driver secures the lane.
 +
* Warning sound: Select  preferred warning sound for LDW.
 +
|[[File:Mdconfi1.png|center|frameless]]
 +
 
 +
|-
 +
| colspan="2" |'''You can adjust the FCW Sensitivity for your  convenience:'''
 +
|-
 +
|
 +
* Enable FCW function. (On  / Off)
 +
* Set the sensitivity of  FCW warning on a scale of 1 to 5.
 +
(As the level  gets higher, it gets more sensitive)
 +
* Enable Repeat FCW (On /  Off).
 +
(If it’s on, ADAS keeps warning until the driver secures safe distance)
 +
* Enable Sync with Brake  (On / Off).
 +
(If it’s on, ADAS won’t give FCW warning if the brake pedal was used)
 +
* Warning sound: Select  preferred warning sound for FCW
 +
|[[File:Mdconf2.png|center|frameless|301x301px]]
 +
|-
 +
| colspan="2" |'''Safety distance alert setup:'''
 +
|-
 +
|
 +
* Enable SDA function. (On  / Off)
 +
* Set the sensitivity of  SDA on a scale of 1 to 5.
 +
* As the level  gets higher, it gets more sensitive.
 +
* Repeat SDA and SDA  re-alert can be changed. (On / Off)
 +
 
 +
- Repeat SDA:  If it’s on, ADAS keeps warning until the driver secures safe distance.
 +
 
 +
''- Re-alert  SDA: If it’s on, ADAS gives warnings every time''
 +
 
 +
''the same front vehicle gets  closer than safe distance.''
 +
|[[File:Mdconfi3.png|center|frameless]]
 +
|-
 +
| colspan="2" |'''Pedestrian collision warning setup:'''
 +
|-
 +
|
 +
* Enable PCW function. (On  / Off)
 +
 
 +
* Warning sound: Select  preferred warning sound for PCW.
 +
|[[File:Mdconfi4.png|center|frameless]]
 +
|-
 +
| colspan="2" |'''Advanced ADAS setup:'''
 +
|-
 +
|
 +
* Enable Forward Proximity  Warning function. (On / Off)
 +
* Set the warning range on  a scale of 1 to 3.
 +
(As the level  gets higher, it gets more sensitive)
 +
* Enable Front vehicle  start alarm. (On / Off)
 +
* Enable Speed Limit  Recognition. (On / Off)
 +
* Set the warning  sensitivity (0, 5, 10, 15, 20%).
 +
Ex) If you  set 10% then you will get alarm
 +
 
 +
when your speed over the limit more than 10%, 
 +
 
 +
100km limit -> Warning start from 110km speed.
 +
* Enable voice guidance (On  / Off).
 +
|[[File:Mdconfi5.1.png|center|frameless]]
 +
|-
 +
| colspan="2" |'''Fleet management setup'''
 +
|-
 +
|
 +
* Set  Speed limit warning (Off, 80, 90, 100, 110, 120, 130, 140km/h).
 +
 
 +
- You  can set your own speed limit for your fleet.
 +
 
 +
- You can set speed limit of your vehicle and  get warning if you over the speed limit.
 +
 
 +
* Enable  Transmit data RS-232 feature
 +
(Converter mode should be selected to work with  FMx125).
 +
 
 +
It allows ADAS event data transmission to integrated device.
 +
* Set Lock  volume button control on a scale of 1 to 5 and Off.
 +
You can fix the volume level and prevent the driver from adjusting the
 +
 
 +
settings using indicator.
 +
* Set Break  time alarm on a scale of 1 to 6 hours and Off.
 +
 
 +
* Enable  Vibration setting for LDW, FCW, PCW (On / Off / Both).
 +
You can check the connection with the button.
 +
|[[File:Mdconfi6.1.png|center|frameless]]
 +
|-
 +
| colspan="2" |'''Miscellaneous  Settings:'''
 +
|-
 +
|
 +
* Speed Unit on Analog  video output (km/h or MPH).
 +
 
 +
* Set Video out format  (NTSC / PAL).
 +
 
 +
* Set Voice guide language
 +
(English /  Korean / Chinese / Spanish / Japanese / Hebrew/ No Sound).
 +
* Enable Indicator buzzer  (On / Off).
 +
 
 +
* Speed Display on  Indicator could be ON/Off
 +
|[[File:Mdconfi7.png|center|frameless]]
 +
|-
 +
| colspan="2" |'''ADAS Setup Complete'''
 +
|-
 +
|
 +
* Click “Complete” button  to finish Calibration setup. Then ADAS will be
 +
rebooted automatically.
 +
* Click “Export vehicle  profile” button, if you want to download vehicleprofile.dat.
 +
 
 +
This vehicleprofile contains all the calibration  settings you’ve set.
 +
 
 +
With this file, you can simply apply current settings to  another vehicle.
 +
|[[File:Mdconfi8.png|frameless|alt=|center|351x351px]]
 +
|}
  
 
==FMx640 Configuration==
 
==FMx640 Configuration==
 +
'''Spec ID Firmware Requirement for FMX640 + ADAS'''
  
  
−
'''It is important to note that ADAS cameras with Serial Numbers (S/N) starting with "9C" are exclusively compatible with FMX6 devices. However, cameras with Serial Numbers beginning with "9B" are typically designed for use with FMX125/225 devices.''' In the event you receive a camera with a Serial Number starting with "9B," it is crucial to check for a red circle sticker on the camera. The presence of this red sticker indicates that the camera, despite its "9B" Serial Number, is actually compatible with FMX6 devices, functioning equivalently to cameras with a "9C" Serial Number. This is due to the serial numbers being pre-attached to the camera case by the manufacturer and remaining constant for warranty purposes. If your camera with a "9B" Serial Number has this red sticker, proceed to connect it to a computer, install the required drivers, and visit IP 10.0.0.1 in a browser. Here, you will find more details about the camera, which will confirm its compatibility with FMX6 devices, as the actual Serial Number displayed will start with "9C.  
+
'''It is important to note that ONLY specific ADAS cameras starting with the Serial Number S/N: 9C can be connected and used with FMX640 devices. Cameras starting with different S/N numbers for example; 9B, are currently not supported.''' However, upon receipt of the cameras, if the S/N number starts with 9B, check whether there is a red circle sticker on the camera as shown in the picture below. If there is, please connect the camera to the computer, install the required drivers and visit IP 10.0.0.1 on the browser. In the further window, details about the camera is displayed where the actual S/N number of the camera will start with 9C meaning that the camera is compatible with FMX640 devices. This is due to the serial numbers being pre-attached to the camera case from the manufacturer and is kept the same for warranty purposes.  
  
−
'''NOTE: You need to insert an SD card into the FMX640 device; otherwise, you will not receive any video or photo on the server.'''
+
[[File:ADAS 9B sticker.png | 250px]]
 +
 
 +
 
 +
Base firmware version of the device will not have the ability to connect ADAS through RS235 connection, it has to be activated using special(spec) firmware. If you want to remove spec ID, you need to install '''FMX64.Ver.01.02.10.Rev.103_ID1''' firmware, after that you can install spec '''ID1039''' firmware.
  
−
[[File:ADAS 9B sticker.png | 250px]]
+
To use firmware '''FMX64.Ver.01.02.10.Rev.103_ID1039''' which has spec ID a spec key is required to be inserted into the configurator '''Teltonika.Configurator_1.7.40_B.FM64_R.55'''
  
−
{| class="wikitable" style="border-style: solid; border-width: 0px;"
+
To do that please go to Teltonika configurator window and press '''Ctrl+Alt+I''' on your keyboard.
−
| style="width: auto; text-align: left; background: #F6F6FB;" |'''NOTE!'''
 
−
| style="width: auto; text-align: left; background: #F6F6FB;" |ADAS devices which start with '''9C''' - will provide a red sticker, as shown on the picture. ADAS devices which start with '''9B''' - '''WILL NOT''' provide a red circle sticker.  
 
  
−
The picture has been only made for explanation purposes, and does not show the real replication of the sticker for 9B.
+
Copy the key:
−
|}
+
jXIEpOLMg6bIyPDZdpIpKgSVCTVdvLyNEua76CNP2TQAAADTTaD1uQ/FhdhfRCCi7PRdtlSutkbDlC9c1UejUWUUSo5bwNhCHG5NGCdn8Qh/DhVppOsbSfH/9Y+8SjUHbqvVNBlKZw9LTIT4nveAKc3ODwy7aumxvQoZEynV9+B44ucUIzDJk9WLVfQfjr54+4O747drg4m/HxoTFGoGg0GuLi7UKFsERiVClqT+b2Qh30L3hBgwgwqxjoUABAAAAAAACIsf<br />
 +
to “New key” section and press Register. If everything is OK, you will see new device added on the left side.
 +
After that you can use ADAS on FMX640
  
 
'''Device Configuration'''
 
'''Device Configuration'''
Line 27: Line 148:
 
[[File:Server222.jpg|alt=|frameless]]
 
[[File:Server222.jpg|alt=|frameless]]
  
−
In RS232/RS485 settings enable ADAS under RS232 mode in order for the configurator to open additional settings for ADAS accessory.  
+
In RS232/RS485 settings enable ADAS under RS232 mode in order for the configurator to open additional settings for ADAS accessory.
  
−
'''Please also note, a new baudrate "460800" is now supported. Please set baudrate settings to either Auto or 460800. This baudrate will allow faster photo/video transfers.'''
+
[[File:RS232-ADAS-selection.png|alt=|frameless|400px]]
−
 
 
−
[[File:ADASbaud2.png|alt=|frameless|500px]]
 
  
 
Once ADAS under RS232 mode is enabled, new tabs will open with additional configurable settings to "ADAS" and "ADAS IO".
 
Once ADAS under RS232 mode is enabled, new tabs will open with additional configurable settings to "ADAS" and "ADAS IO".
Line 100: Line 219:
  
 
Re-Alert setting gives warning if the same vehicle in the front gets too close every time.  
 
Re-Alert setting gives warning if the same vehicle in the front gets too close every time.  
−
 
−
{| class="wikitable"
 
−
|-
 
−
! colspan="5" | SDA sensitivity
 
−
|- style="font-weight:bold;"
 
−
| Level 1
 
−
| Level 2
 
−
| Level 3 (Default)
 
−
| Level 4
 
−
| Level 5
 
−
|-
 
−
| 0.6 sec
 
−
| 0.9 sec
 
−
| 1.2 sec
 
−
| 1.5 sec
 
−
| 2.0 sec
 
−
|}
 
  
 
'''Pedestrian collision warning PCW'''
 
'''Pedestrian collision warning PCW'''
Line 144: Line 246:
 
[[File:ADAS-settings11.png|alt=|frameless|400px]]
 
[[File:ADAS-settings11.png|alt=|frameless|400px]]
  
−
File upload settings feature is responsible for image and video sending to user's preferred server if they require these files to be sent to another server or even the same server but different port.  
+
File upload settings feature is responsible for image and video sending to user's preferred server if they require these files to be sent to another server or even same server but different port.  
  
−
Periodic image-sending functionality is also available with configurable sending intervals.  
+
Periodic image sending functionality is also available with configurable sending interval.  
  
−
Image and Video sending can also be triggered by different inputs such as DINs for photos and videos, and different FMX640 features such as Crash, Towing, Idling and etc for photos.  
+
Image and Video sending can also be triggered by different inputs such as DIN's for photo's and videos, and different FMX640 features such as Crash, Towing, Idling and etc for photos.  
  
 
Video duration can also be configured before and after the trigger event.  
 
Video duration can also be configured before and after the trigger event.  
Line 160: Line 262:
 
Available information to display can be chosen between "Date and time", "GPS information" and "Speed".  
 
Available information to display can be chosen between "Date and time", "GPS information" and "Speed".  
  
−
GPS information can have a configurable update period which can be specified by the user allowing the device to use more or less network resources.  
+
GPS information can have configurable update period which can be specified by the user allowing the device to use more or less network resources.  
−
 
 
−
If you choose to use the "Speed" overlay, you will have four different options to choose from: <b>GPS, CAN adapter, FMS or K-Line</b>. Once you select one of these options, it will be used as the source for your speed information. Speed overlay settings can be useful in case wiring schemes are not available for specific vehicles, that way it would allow more flexible speed source configuration.
 
−
 
 
−
The overlay information update period determines how often information will be updated. Recommended value is <b>1000 ms</b>
 
  
 
'''Garbage collector'''
 
'''Garbage collector'''
Line 170: Line 268:
 
[[File:ADAS-settings13.png|alt=|frameless|400px]]
 
[[File:ADAS-settings13.png|alt=|frameless|400px]]
  
−
ADAS system can save files inside of itself or FMX640 device if an additional microSD card is connected. However, from time to time, a lot of files can be accumulated which in turn will fill up the free space overcrowding the card and new files will stop producing. To reduce the hassle of taking out the card and deleting the contents inside of it manually, garbage collector functionality is introduced. It automatically deletes all records older than the specified days thus freeing up the space in the microSD card allowing it efficiently operate for longer periods of time.
+
ADAS system can save files inside of itself or FMX640 device if additional microSD card is connected. However, from time to time, a lot of files can be accumulated which in turn will fill up the free space overcrowding the card and new files will stop producing. To reduce the hassle of taking out the card and deleting the contents inside of it manually, garbage collector functionality is introduced. It automatically deletes all records older than the specified days thus freeing up the space in microSD card allowing it efficiently operate for longer periods of time.
−
 
 
−
'''ADAS IO'''
 
−
 
 
−
New IO elements called "ADAS" will appear in the configurator. Under this tab, the user can select either low or high priority on different features which they would like to receive on their server. Selecting priority will also allow the users to receive specific ADAS functionalities and ignore the ones they do not need.
 
−
 
 
−
[[File:Adas conf2.png|center|frameless|1000x1000px]]
 
−
 
 
−
==ADAS configuration for FMx650==
 
−
 
 
−
'''(!) Required firmware version - 03.00.14.Rev.116'''. [[DSM_Firmware_errata|Firmware errata.]]
 
−
 
 
−
*Make sure '''Data Protocol''' is set to [[Codec#Codec_8_Extended | Codec 8 Extended]]
 
−
 
 
−
[[Image:Data_protocol.gif|300px]]
 
−
 
 
−
*In ''RS232 \ RS485 settings tab'', make sure to enable '''Camera interface''' by "Enable", and select '''ADAS''' in the Mode drop-down menu, afterwards '''ADAS COM1''' and '''Camera I/O''' should appear in the tab list.
 
−
 
 
−
[[Image:ADAS COM1.gif|600px]]
 
−
 
 
−
*Make sure to change '''Camera I/O''' camera state '''Priorities''' to ''Low''
 
−
'''
 
−
[[File:ADAS CameraIO.gif|500px]]
 
−
'''
 
−
 
 
−
*In appeared ''ADAS COM1'' tab, make sure to '''configure everything by your needs''', and do not forget to complete the '''"Domain"''' and '''"Port"''' settings in ''File upload settings''
 
−
 
 
−
[[File:ADAS.png|500px]]
 
−
 
 
−
 
 
−
*'''''NOTE:''''' ''This is a base setup for the device to work properly. Other device configuration is made according to your needs.
 
−
 
 
−
===Connecting two cameras simultaneously for FMx650===
 
−
------------------
 
−
The new feature for FMx650 ADAS configuration, which is available from '''03.00.14.Rev.114-Rev.116 iCamera''' allows you to connect two of your cameras at once. Method for connection and configuration stays the same, for this you are only required to choose '''two''' cameras in '''"RS232 \ RS485"''' tab from the configurator.
 
−
 
 
−
In the new functionality, you are able to connect any combo of the cameras by your wish, as an example: you are able to connect ''ADAS/DSM'', ''ADAS/DualCam'', ''DSM/Dualcam'', ''DashCam/DualCam'', ''DSM/DSM'', ''DualCam/DualCam'' and etc.
 
−
 
 
−
[[File:Twincamera.gif|500px]]
 
  
 
==FMx125/FMX225 Configuration==
 
==FMx125/FMX225 Configuration==
−
ADAS functionality is intended for use with devices, that have RS232. It was implemented in '''FMB.Ver.03.27.01.Rev.242'''. New RS232 mode was implemented for ADAS camera data reading and a new ADAS IO section was created.
+
ADAS functionality is intended for use with devices, that have RS232. It was implemented in '''FMB.Ver.03.27.01.Rev.240'''. New RS232 mode was implemented for ADAS camera data reading and new ADAS IO section was created.
  
 
In order for ADAS functionality to work „ADAS Camera“ RS232 mode has to be selected (151 parameter ID, value 21).
 
In order for ADAS functionality to work „ADAS Camera“ RS232 mode has to be selected (151 parameter ID, value 21).
−
[[File:Rs232adas.jpg|center|frameless|250x250px]]
+
[[File:Rs232adas.jpg|center|frameless|187x187px]]
 +
New IO elements
 +
[[File:Adasconf1.png|center|frameless|1178x1178px]]
  
−
'''Note''':
 
  
 +
'''Note''':
 
1) Please use Codec08 extended protocol with ADAS functionality
 
1) Please use Codec08 extended protocol with ADAS functionality
−
 
+
[[File:Codec8adas.png|center|frameless]]
−
[[File:Codec8adas.png|center|frameless|300x300px]]
 
−
 
 
 
2) RS232 baudrate should be configured 115200 bps
 
2) RS232 baudrate should be configured 115200 bps
−
 
+
[[File:Adas232set.png|center|frameless]]
−
[[File:Adas232set.png|center|frameless|300x300px]]
 
−
 
 
−
3) New IO elements called "ADAS" will appear in the configurator. Under this tab, the user can select either low or high priority on different features which they would like to receive on their server. Selecting priority will also allow the users to receive specific ADAS functionalities and ignore the ones they do not need.
 
−
 
 
−
[[File:Adasconf1.png|center|frameless|1000x1000px]]
 
−
 
 
−
==Crash Detection Functionality using DOUT==
 
−
 
 
−
'''The crash detection feature''' is a crucial capability provided by our device. It enhances evidential documentation through video or photo evidence in the event of a crash. However, activating this functionality necessitates a direct connection of the camera to a power source. Nonetheless, such a direct connection can lead to '''battery drainage'''.
 
−
 
 
−
To circumvent this issue, we recommend utilizing DOUT and a relay for connection. This setup enables control via SMS or GPRS command, or through predefined scenarios within our device. By activating DOUT post-ignition, the camera receives power, allowing it to function and record evidence even after the ignition is turned off following a crash. '''For your convenience, the connection scheme can be found here: [[ADAS First Start]]'''
 
−
 
 
−
'''It is important to note that in the event of a fatal crash where fatalities may occur,''' we cannot guarantee the retrieval of video or photo evidence due to the severity of the accident. Moreover, both the camera and the device itself may sustain irreparable damage in such instances
 
−
 
 
−
[[Category:DSM]]
 
−
 
 
−
 
 
−
[[Category: Teltonika ADAS]]
 

Revision as of 07:33, 30 August 2022

Main Page > Video Solutions > DSM > ADAS Configuration

ADAS configuration

You can adjust the LDW Sensitivity for your convenience
  • Enable LDW function. (On / Off)
  • Set the Activation Speed (15, 30, 45, 60, 75km/h).
  • Set the sensitivity of LDW warning on a scale of 1 to 5.
  • As the level gets higher, it gets more sensitive.
  • Enable Repeat LDW (On / Off)
  • If it’s on, ADAS keeps warning until the driver secures the lane.
  • Warning sound: Select preferred warning sound for LDW.
Mdconfi1.png
You can adjust the FCW Sensitivity for your convenience:
  • Enable FCW function. (On / Off)
  • Set the sensitivity of FCW warning on a scale of 1 to 5.

(As the level gets higher, it gets more sensitive)

  • Enable Repeat FCW (On / Off).

(If it’s on, ADAS keeps warning until the driver secures safe distance)

  • Enable Sync with Brake (On / Off).

(If it’s on, ADAS won’t give FCW warning if the brake pedal was used)

  • Warning sound: Select preferred warning sound for FCW
Mdconf2.png
Safety distance alert setup:
  • Enable SDA function. (On / Off)
  • Set the sensitivity of SDA on a scale of 1 to 5.
  • As the level gets higher, it gets more sensitive.
  • Repeat SDA and SDA re-alert can be changed. (On / Off)

- Repeat SDA: If it’s on, ADAS keeps warning until the driver secures safe distance.

- Re-alert SDA: If it’s on, ADAS gives warnings every time

the same front vehicle gets closer than safe distance.

Mdconfi3.png
Pedestrian collision warning setup:
  • Enable PCW function. (On / Off)
  • Warning sound: Select preferred warning sound for PCW.
Mdconfi4.png
Advanced ADAS setup:
  • Enable Forward Proximity Warning function. (On / Off)
  • Set the warning range on a scale of 1 to 3.

(As the level gets higher, it gets more sensitive)

  • Enable Front vehicle start alarm. (On / Off)
  • Enable Speed Limit Recognition. (On / Off)
  • Set the warning sensitivity (0, 5, 10, 15, 20%).

Ex) If you set 10% then you will get alarm

when your speed over the limit more than 10%,

100km limit -> Warning start from 110km speed.

  • Enable voice guidance (On / Off).
Mdconfi5.1.png
Fleet management setup
  • Set Speed limit warning (Off, 80, 90, 100, 110, 120, 130, 140km/h).

- You can set your own speed limit for your fleet.

- You can set speed limit of your vehicle and get warning if you over the speed limit.

  • Enable Transmit data RS-232 feature

(Converter mode should be selected to work with FMx125).

It allows ADAS event data transmission to integrated device.

  • Set Lock volume button control on a scale of 1 to 5 and Off.

You can fix the volume level and prevent the driver from adjusting the

settings using indicator.

  • Set Break time alarm on a scale of 1 to 6 hours and Off.
  • Enable Vibration setting for LDW, FCW, PCW (On / Off / Both).

You can check the connection with the button.

Mdconfi6.1.png
Miscellaneous Settings:
  • Speed Unit on Analog video output (km/h or MPH).
  • Set Video out format (NTSC / PAL).
  • Set Voice guide language

(English / Korean / Chinese / Spanish / Japanese / Hebrew/ No Sound).

  • Enable Indicator buzzer (On / Off).
  • Speed Display on Indicator could be ON/Off
Mdconfi7.png
ADAS Setup Complete
  • Click “Complete” button to finish Calibration setup. Then ADAS will be

rebooted automatically.

  • Click “Export vehicle profile” button, if you want to download vehicleprofile.dat.

This vehicleprofile contains all the calibration settings you’ve set.

With this file, you can simply apply current settings to another vehicle.

FMx640 Configuration

Spec ID Firmware Requirement for FMX640 + ADAS


It is important to note that ONLY specific ADAS cameras starting with the Serial Number S/N: 9C can be connected and used with FMX640 devices. Cameras starting with different S/N numbers for example; 9B, are currently not supported. However, upon receipt of the cameras, if the S/N number starts with 9B, check whether there is a red circle sticker on the camera as shown in the picture below. If there is, please connect the camera to the computer, install the required drivers and visit IP 10.0.0.1 on the browser. In the further window, details about the camera is displayed where the actual S/N number of the camera will start with 9C meaning that the camera is compatible with FMX640 devices. This is due to the serial numbers being pre-attached to the camera case from the manufacturer and is kept the same for warranty purposes.

ADAS 9B sticker.png


Base firmware version of the device will not have the ability to connect ADAS through RS235 connection, it has to be activated using special(spec) firmware. If you want to remove spec ID, you need to install FMX64.Ver.01.02.10.Rev.103_ID1 firmware, after that you can install spec ID1039 firmware.

To use firmware FMX64.Ver.01.02.10.Rev.103_ID1039 which has spec ID a spec key is required to be inserted into the configurator Teltonika.Configurator_1.7.40_B.FM64_R.55

To do that please go to Teltonika configurator window and press Ctrl+Alt+I on your keyboard.

Copy the key: 

jXIEpOLMg6bIyPDZdpIpKgSVCTVdvLyNEua76CNP2TQAAADTTaD1uQ/FhdhfRCCi7PRdtlSutkbDlC9c1UejUWUUSo5bwNhCHG5NGCdn8Qh/DhVppOsbSfH/9Y+8SjUHbqvVNBlKZw9LTIT4nveAKc3ODwy7aumxvQoZEynV9+B44ucUIzDJk9WLVfQfjr54+4O747drg4m/HxoTFGoGg0GuLi7UKFsERiVClqT+b2Qh30L3hBgwgwqxjoUABAAAAAAACIsf

to “New key” section and press Register. If everything is OK, you will see new device added on the left side. After that you can use ADAS on FMX640

Device Configuration

It is necessary to change Data Protocol to Codec 8 Extended

Data protocol.gif

Configure the Domain and Port to send the data to the desired server.

In RS232/RS485 settings enable ADAS under RS232 mode in order for the configurator to open additional settings for ADAS accessory.

Once ADAS under RS232 mode is enabled, new tabs will open with additional configurable settings to "ADAS" and "ADAS IO".

In these settings it is important to remember that when a feature is enabled under "ADAS" tab, in order for the FMX640 device to send data about this feature to the server, it has to be given a priority "Low, Medium, High" inside of "ADAS IO" tab.

Crash event video settings

These settings are responsible for video length before and after the event. User can set up to 20 seconds of video data to be saved before the crash and a maximum of 10 seconds after the crash. A minimum of 5 seconds is required between the both settings.

Please note, more seconds means longer sending periods and more data usage.

Image/video settings

Image/video resolution can be chosen between 640x480 and 1280x720.

Please note, 1280x720 resolution is almost twice as large as the 640x480. This means that videos would take much larger storage space and sending them to the server would take more time.

Forward vehicle start alarm FVSA

This setting enables front vehicle movement detection and sets up an alarm once the vehicle starts moving.

Sensitivity ranging from 1 to 5 where 1 is least sensitive and 5 is the most sensitive option. Warning sound can be set by the user to their liking.

Speed limit recognition SLR

This setting allows fleet management companies or users to set maximum speed limit for that one particular vehicle and if that speed is exceeded, the driver is notified.

Sensitivity setting would indicate how sensitive the ADAS camera would be to exceeding speed limit, 1 would be least sensible giving driver the most room for exceeding the speed limit whereas 5 would strictly stick to the speed limit.

Lane departure warning LDW

This feature allows ADAS camera to track driver's lane changing and will notify the driver if the vehicle is moving out of its lane. This feature is also effective if the driver falls asleep and the vehicle starts to swivel.

Activation speed is a setting from which this feature activates.

Sensitivity settings determines how sensitive the camera will be to swiveling on the road meaning 1, swiveling in lane should not activate this feature while 5 which is the highest sensitivity will activate the feature if the vehicle swivels more than it should.

Warning sound repeat can be turned on which will keep on making warning sound until vehicle returns to lane.

Forward collision warning FCW

This feature if enabled, notified the driver if the vehicle is getting too close to the obstacle in front.

Sync with brake allows the ADAS camera to deactivate warning sounds if it detects vehicle stopping meaning the driver is aware of obstacle in the front.

Vibration activation will notify the driver when the vehicle is hitting small object which are too small for camera to notice so instead, vehicle starts to vibrate during collision with small objects and therefore the feature will activate warning sounds. Sensitivity setting will determine whether weak vibration should be detected or not.

Repeat function will keep the warning sounds on until the event will deactivate

Safety distance alert SDA

This feature activates if the vehicle in front is too close and the distance should be increased.

Re-Alert setting gives warning if the same vehicle in the front gets too close every time.

Pedestrian collision warning PCW

This feature if enabled, notified the driver if the vehicle is getting too close to the obstacle in front.

Vibration activation will notify the driver when the vehicle is hitting small object which are too small for camera to notice so instead, vehicle starts to vibrate during collision with small objects and therefore the feature will activate warning sounds. Sensitivity setting will determine whether weak vibration should be detected or not.

Forward proximity warning FPW

This feature once enabled, provides warning if there is an object in the front of the vehicle or within ADAS camera's proximity.

Sensitivity from 1 to 5 is responsible for distance the event triggers, 1 is the least sensitive option while 5 is the strongest sensitivity.

Event Indication

This feature allows ADAS system to work in sync with FMX640 safety driving features such as Eco-driving, Over Speeding and Geofence. These features usually work with buzzers, LEDs and etc. connected straight to FMX640 device as outputs however, FMX640 devices can be connected straight with ADAS system which has sound warnings and the need for external peripherals is not required anymore.

File upload settings

File upload settings feature is responsible for image and video sending to user's preferred server if they require these files to be sent to another server or even same server but different port.

Periodic image sending functionality is also available with configurable sending interval.

Image and Video sending can also be triggered by different inputs such as DIN's for photo's and videos, and different FMX640 features such as Crash, Towing, Idling and etc for photos.

Video duration can also be configured before and after the trigger event.

Overlay

Image and video records can have specific overlays on it recorded in order to provide additional information to the viewer.

Available information to display can be chosen between "Date and time", "GPS information" and "Speed".

GPS information can have configurable update period which can be specified by the user allowing the device to use more or less network resources.

Garbage collector

ADAS system can save files inside of itself or FMX640 device if additional microSD card is connected. However, from time to time, a lot of files can be accumulated which in turn will fill up the free space overcrowding the card and new files will stop producing. To reduce the hassle of taking out the card and deleting the contents inside of it manually, garbage collector functionality is introduced. It automatically deletes all records older than the specified days thus freeing up the space in microSD card allowing it efficiently operate for longer periods of time.

FMx125/FMX225 Configuration

ADAS functionality is intended for use with devices, that have RS232. It was implemented in FMB.Ver.03.27.01.Rev.240. New RS232 mode was implemented for ADAS camera data reading and new ADAS IO section was created.

In order for ADAS functionality to work „ADAS Camera“ RS232 mode has to be selected (151 parameter ID, value 21).

Rs232adas.jpg

New IO elements

Adasconf1.png


Note: 1) Please use Codec08 extended protocol with ADAS functionality

Codec8adas.png

2) RS232 baudrate should be configured 115200 bps

Adas232set.png
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=ADAS_Configuration&oldid=75535"