Difference between revisions of "DSM First Start"

From Wiki Knowledge Base | Teltonika GPS
(45 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
{| class="wikitable" style="border-style: solid; border-width: 0px;"
+
==PC Calibration==
−
| style="width: auto; text-align: left; background: #F6F6FB;" |'''(!) Only works with FMx640 and FMC650'''
+
[[File:DSM_Calib.png | right | 320x320px]]
−
|}
+
Driver Setup (ONLY SUPPORTS WINDOWS OS)
 +
* NOTE: Before you connect or start calibration, please install RNDIS driver first.
 +
Calibration Setup
 +
* Access DSM Calibration page via PC
 +
** Connect DSM to PC using Micro USB cable with 5 pins.
 +
** Power on DSM. If you hear repeated beep sound, this means DSM is properly connected to computer.
 +
** Activate the browser and enter into http://20.0.0.1:18087/ to access DSM calibration page. Google Chrome is recommended.
 +
** If you see the page below, please select language you want and sign in using following information
 +
  ‐ ID: admin ‐ Password: 1234
  
−
==DSM connection scheme==
+
Calibration
 +
* Select Speed Type
 +
** GPS Speed setting - GPS antenna is embedded on DSM. If GPS work correctly, detected is shown. If GPS doesn’t work for 5 mins, Fail is shown.
  
−
'''Please note that camera must be connected to ignition source, in other way camera will drain battery.'''
+
[[File:DSM Calib2.png|400px|center-left]] [[File:DSM Calib3.png|400px|center-right]]
  
−
[[File:DSM connection scheme.jpg|800px]]
 
  
 +
CAN Speed setting
 +
*DSM can get speed through CAN as well.
 +
*DSM only recognizes encrypted CAN data from our Database site; http://info.mdas.co.kr
  
−
'''Camera connection through a relay'''
 
  
−
If you need to receive additional data from the DSM when the ignition is off but the key is inserted and turned to ACC postition, you can do it by connecting the camera to a power source using a relay in order to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].
 
  
−
[[File:DSM connection.jpg|800px]]
 
  
−
'''Two cameras FMC650 Installation with Ignition Source'''. To connect the two cameras to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.
 
  
−
'''NOTE:''' Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.
+
Next chapter
−
 
+
[[File:Auto Camera Setting img.jpg|500px|center]]
−
[[File:688548 DualCam and DSM with FMC650.jpg]]
 
−
 
 
−
'''Two cameras FMC650 Installation with Relay'''. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].
 
−
 
 
−
[[File:2 cameras dout.JPG|frameless|928x928px]]
 
−
 
 
−
 
 
−
'''NOTE: FMX640 device also needs SD Card to be inserted. The FMX650 can be used with the feature without an SD card.'''
 
−
 
 
−
Using the above information in regards to connection, please follow the below steps:
 
−
 
 
−
# Insert Micro SD Card into the DSM camera main block.
 
−
# Connect DSM camera to the main block
 
−
# Connect main block with power and ground wires either to the vehicles relay (see picture above) or power supply.
 
−
# The RX and TX cables from the main block have to be connected through the RJ-45 cable to the FMX640 device. '''Pin can be 3/4 or 5/6 different RJ45 cable modification'''
 
−
# Connect FMX640 device with PWR and Ground to power supply or vehicle's relay (see picture above).
 
−
# Connect DOUT (1,2,3,4) to relay in order to control immobilizer and DSM camera state.
 
−
# Continue in configurator in order to set up the DSM camera [https://wiki.teltonika-gps.com/view/DSM_Configuration here].
 
−
 
 
−
 
 
−
[[Category:DSM]]
 

Revision as of 16:04, 6 October 2022

Main Page > Video Solutions > DSM > DSM First Start

PC Calibration

DSM Calib.png

Driver Setup (ONLY SUPPORTS WINDOWS OS)

  • NOTE: Before you connect or start calibration, please install RNDIS driver first.

Calibration Setup

  • Access DSM Calibration page via PC
    • Connect DSM to PC using Micro USB cable with 5 pins.
    • Power on DSM. If you hear repeated beep sound, this means DSM is properly connected to computer.
    • Activate the browser and enter into http://20.0.0.1:18087/ to access DSM calibration page. Google Chrome is recommended.
    • If you see the page below, please select language you want and sign in using following information
 ‐ ID: admin ‐ Password: 1234

Calibration

  • Select Speed Type
    • GPS Speed setting - GPS antenna is embedded on DSM. If GPS work correctly, detected is shown. If GPS doesn’t work for 5 mins, Fail is shown.

center-left center-right


CAN Speed setting

  • DSM can get speed through CAN as well.
  • DSM only recognizes encrypted CAN data from our Database site; http://info.mdas.co.kr



Next chapter

Auto Camera Setting img.jpg
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=DSM_First_Start&oldid=76764"