Difference between revisions of "DSM First Start"

From Wiki Knowledge Base | Teltonika GPS
(12 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
{| class="wikitable" style="border-style: solid; border-width: 0px;"
+
__TOC__
−
| style="width: auto; text-align: left; background: #F6F6FB;" |'''(!) Only works with FMx640 and FMC650'''
 
−
|}
 
  
 
==DSM connection scheme==
 
==DSM connection scheme==
  
−
'''Please note that camera must be connected to ignition source, in other way camera will drain battery.'''
+
'''Please note that camera must be connected to ignition source, in other way camera will drain battery:'''
  
 
[[File:DSM connection scheme.jpg|800px]]
 
[[File:DSM connection scheme.jpg|800px]]
  
  
−
'''Camera connection through a relay'''
+
'''Camera connection through a relay:'''
  
−
If you need to receive additional data from the DSM when the ignition is off but the key is inserted and turned to ACC postition, you can do it by connecting the camera to a power source using a relay in order to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].
+
[[File:DSM connection.jpg|800px]]
 +
 
 +
 
 +
'''NOTE: FMX640 device also needs SD Card to be inserted.'''
 +
 
 +
==PC Calibration==
 +
Driver Setup (ONLY SUPPORTS WINDOWS OS)
 +
* If connecting the DSM camera to computer, the calibration page is not available, please follow the steps below:
 +
* Please install RNDIS driver. LINK: http://movon.co.kr/downloads/rndisdriver.zip (Windows 10)
 +
* If the driver does not install itself automatically, please follow the guide in this document [[Media:DSM RNDIS driver installation.pdf| here]]
 +
* Unzip the file and remember the unzipped folder location.
 +
 
 +
 
 +
[[File:DSM_Calib.png | right | 320x320px]]
 +
==== Calibration Setup ====
 +
* Access DSM Calibration page via PC
 +
** Connect DSM to PC using  USB Tipe-C cable with 5 pins.
 +
** Power on DSM. If you hear repeated beep sound, this means DSM is properly connected to computer.
 +
** Activate the browser and enter into http://20.0.0.1:18087/ to access DSM calibration page. Google Chrome is recommended.
 +
** If you see the page below, please select language you want and sign in using following information
 +
  ‐ ID: admin ‐ Password: 1234
 +
 
 +
==== Calibration ====
 +
* Select Speed Type
 +
** GPS Speed setting - GPS antenna is embedded on DSM. If GPS work correctly, detected is shown. If GPS doesn’t work for 5 mins, Fail is shown.
 +
 
 +
[[File:DSM Calib2.png|400px|center-left]] [[File:DSM Calib3.png|400px|center-right]]
 +
 
 +
====  CAN Speed setting ====
 +
*DSM can get speed through CAN as well.
 +
*DSM only recognizes encrypted CAN data from our Database site; http://info.mdas.co.kr
 +
 
 +
Please download can file from the DB and upload to system.
 +
 
 +
[[File:Mdas1.0.png|frameless|450x450px]]
 +
 
 +
==== Verify Speed Signal ====
 +
You can check the speed data is coming correct by test drive.
 +
 
 +
If there is a deviation, please use the following correction method.
 +
 
 +
Please click the “Correction” button when you drive at 40km/h (24mph). Then, DSM will set new speed automatically.
 +
[[File:Mdas1.1.png|450x450px]]
 +
 
 +
==== Camera Setting ====
  
−
[[File:DSM connection.jpg|800px]]
+
# Calibrate camera, that face will be in center of the image in calibration page.
 +
# After that, just go to the next step.
 +
 
 +
[[File:Auto Camera Setting img.jpg|450x450px]]
 +
 
 +
==== DSM Setup ====
 +
The camera can also be configured through its configuration, main settings that which can be seen are pointed below:
 +
 
 +
[[File:Dms1.03.png]]
 +
 
 +
Configurable parameters:
 +
 
 +
*ON/OFF: Enable Drowsiness, Distraction, Phone, Smoking, Yawning.
 +
*Sound Type: Check the warning sound and select the one you prefer. Press Play button to test Warning Alarm Sound.
 +
*Vibrator: Enable vitration function. (On / Off)
 +
*Sensitivity: Set the sensitivity on a scale of 1 to 3. As the level gets higher, it gets more sensitive. Yawning warning will generate when yawning for 2 seconds.
 +
*Activation Speed:
 +
# You can set up activation speed by DSM alert respectively.
 +
# Set the Activation Speed ( 15 ~ 60Km/h ≒ 10 ~ 40mph). The functions will be acticvated when the vehicle is faster than this speed.
 +
# If you select Others, you can input the activation speed in the below box. Note that the input range is between 5Km and 100km.
 +
* DIP switch on unit: Enable DIP switch on DSM’s unit.
 +
* Sound Level: Control the warning sound level on a scale of 1 to 4.
 +
* Test Mode : If you want to test DSM at any speed, please select “ON” ⑨ Time-out Feature: Select if apply below time-out logic. (On / Off) * Time-out feature: An event and chime will be fired when ‘First Trigger Count’ number of triggers happen within ‘First Trigger Interval’. After the first event and chine, additional events’chimes up to ‘Max Trigger Count’ will be fired as long as they happen within ‘Max Trigger Interval’. When ‘First Trigger Interval’ or ‘Max Trigger Interval’ expire, the trigger count it reset to 0.
 +
 
 +
==== Driver Registration ====
 +
Face ID or driver registration is required in order for the camera to recognize different drivers. In the DSM menu, click on "Driver Registration" and follow the steps below in order to calibrate the camera angle:
  
−
'''Two cameras FMC650 Installation with Ignition Source'''. To connect the two cameras to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.  
+
Look into camera and click "next" once you have the distance and angle set accordingly.
  
−
'''NOTE:''' Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.
+
[[File:Dsmsetupnew.jpg]]
  
−
[[File:688548 DualCam and DSM with FMC650.jpg]]
+
Once this is done, name the photo with the driver ID or name and keep the document uploaded inside DSM.
  
−
'''Two cameras FMC650 Installation with Relay'''. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].
+
==Mobile connection & calibration==
  
−
[[File:2 cameras dout.JPG|frameless|928x928px]]
+
=====App installation=====
 +
Download Movon application from the app gallery. The app is called "Movon".  
  
 +
[[File:Movon app.jpg]]
  
−
'''NOTE: FMX640 device also needs SD Card to be inserted. The FMX650 can be used with the feature without an SD card.'''
+
===== Login =====
 +
Please enter the information below to log in
 +
  ID: admin
 +
  PW: 1234
 +
Once this is done, click the link to download the vehicle CAN file from this link http://info.mdas.co.kr or press the “Vehicle CAN file” button in the application.[[File:Movon app1.jpg|387x387px]]
  
−
Using the above information in regards to connection, please follow the below steps:  
+
===== Wifi setup =====
 +
How to get into Wi-Fi Mode:
  
−
# Insert Micro SD Card into the DSM camera main block.
+
Wi-Fi is available for 5 minutes after DSM is turned on.  
−
# Connect DSM camera to the main block
 
−
# Connect main block with power and ground wires either to the vehicles relay (see picture above) or power supply.
 
−
# The RX and TX cables from the main block have to be connected through the RJ-45 cable to the FMX640 device. '''Pin can be 3/4 or 5/6 different RJ45 cable modification'''
 
−
# Connect FMX640 device with PWR and Ground to power supply or vehicle's relay (see picture above).
 
−
# Connect DOUT (1,2,3,4) to relay in order to control immobilizer and DSM camera state.
 
−
# Continue in configurator in order to set up the DSM camera [https://wiki.teltonika-gps.com/view/DSM_Configuration here].  
 
  
 +
Press the button(MFB) on side of the camera for 5 seconds to activate Wi-Fi Mode (stay in Wi-Fi mode for 5 minutes).
  
 +
* If the device cannot connect to the Wi-Fi, please reboot the device and try again.
 +
* If connecting through iPhone, please use password: 123456789.
 +
[[File:Movon app2.jpg]]
 
[[Category:DSM]]
 
[[Category:DSM]]

Revision as of 09:41, 21 February 2023

Main Page > Video Solutions > DSM > DSM First Start

DSM connection scheme

Please note that camera must be connected to ignition source, in other way camera will drain battery:

DSM connection scheme.jpg


Camera connection through a relay:

DSM connection.jpg


NOTE: FMX640 device also needs SD Card to be inserted.

PC Calibration

Driver Setup (ONLY SUPPORTS WINDOWS OS)

  • If connecting the DSM camera to computer, the calibration page is not available, please follow the steps below:
  • Please install RNDIS driver. LINK: http://movon.co.kr/downloads/rndisdriver.zip (Windows 10)
  • If the driver does not install itself automatically, please follow the guide in this document here
  • Unzip the file and remember the unzipped folder location.


DSM Calib.png

Calibration Setup

  • Access DSM Calibration page via PC
    • Connect DSM to PC using USB Tipe-C cable with 5 pins.
    • Power on DSM. If you hear repeated beep sound, this means DSM is properly connected to computer.
    • Activate the browser and enter into http://20.0.0.1:18087/ to access DSM calibration page. Google Chrome is recommended.
    • If you see the page below, please select language you want and sign in using following information
 ‐ ID: admin ‐ Password: 1234

Calibration

  • Select Speed Type
    • GPS Speed setting - GPS antenna is embedded on DSM. If GPS work correctly, detected is shown. If GPS doesn’t work for 5 mins, Fail is shown.

center-left center-right

CAN Speed setting

  • DSM can get speed through CAN as well.
  • DSM only recognizes encrypted CAN data from our Database site; http://info.mdas.co.kr

Please download can file from the DB and upload to system.

Mdas1.0.png

Verify Speed Signal

You can check the speed data is coming correct by test drive.

If there is a deviation, please use the following correction method.

Please click the “Correction” button when you drive at 40km/h (24mph). Then, DSM will set new speed automatically. Mdas1.1.png

Camera Setting

  1. Calibrate camera, that face will be in center of the image in calibration page.
  2. After that, just go to the next step.

Auto Camera Setting img.jpg

DSM Setup

The camera can also be configured through its configuration, main settings that which can be seen are pointed below:

Dms1.03.png

Configurable parameters:

  • ON/OFF: Enable Drowsiness, Distraction, Phone, Smoking, Yawning.
  • Sound Type: Check the warning sound and select the one you prefer. Press Play button to test Warning Alarm Sound.
  • Vibrator: Enable vitration function. (On / Off)
  • Sensitivity: Set the sensitivity on a scale of 1 to 3. As the level gets higher, it gets more sensitive. Yawning warning will generate when yawning for 2 seconds.
  • Activation Speed:
  1. You can set up activation speed by DSM alert respectively.
  2. Set the Activation Speed ( 15 ~ 60Km/h ≒ 10 ~ 40mph). The functions will be acticvated when the vehicle is faster than this speed.
  3. If you select Others, you can input the activation speed in the below box. Note that the input range is between 5Km and 100km.
  • DIP switch on unit: Enable DIP switch on DSM’s unit.
  • Sound Level: Control the warning sound level on a scale of 1 to 4.
  • Test Mode : If you want to test DSM at any speed, please select “ON” ⑨ Time-out Feature: Select if apply below time-out logic. (On / Off) * Time-out feature: An event and chime will be fired when ‘First Trigger Count’ number of triggers happen within ‘First Trigger Interval’. After the first event and chine, additional events’chimes up to ‘Max Trigger Count’ will be fired as long as they happen within ‘Max Trigger Interval’. When ‘First Trigger Interval’ or ‘Max Trigger Interval’ expire, the trigger count it reset to 0.

Driver Registration

Face ID or driver registration is required in order for the camera to recognize different drivers. In the DSM menu, click on "Driver Registration" and follow the steps below in order to calibrate the camera angle:

Look into camera and click "next" once you have the distance and angle set accordingly.

Dsmsetupnew.jpg

Once this is done, name the photo with the driver ID or name and keep the document uploaded inside DSM.

Mobile connection & calibration

App installation

Download Movon application from the app gallery. The app is called "Movon".

Movon app.jpg

Login

Please enter the information below to log in 

 ID: admin
 PW: 1234

Once this is done, click the link to download the vehicle CAN file from this link http://info.mdas.co.kr or press the “Vehicle CAN file” button in the application.Movon app1.jpg

Wifi setup

How to get into Wi-Fi Mode:

Wi-Fi is available for 5 minutes after DSM is turned on.

Press the button(MFB) on side of the camera for 5 seconds to activate Wi-Fi Mode (stay in Wi-Fi mode for 5 minutes).

  • If the device cannot connect to the Wi-Fi, please reboot the device and try again.
  • If connecting through iPhone, please use password: 123456789.

Movon app2.jpg

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=DSM_First_Start&oldid=80250"