299
edits
Changes
→Crash Detection Functionality using DOUT
__TOC__
__TOC__
==Device configuration==
==DSM calibration==
If it is the first DSM launch, please make sure to calibrate the device, and change the important settings, to ensure the correct device working: [[DSM Calibration]]
==Device configuration for FMx640==
On this page, you will be able to find information about the gerenal configuration and connection of DSM camera with the FMX640 tracking device. Information about different parameters required to set up the DSM camera are also described in this page. To start off, firstly follow the instructions on how to connect DSM camera with the FMX640 device, once the camera is connected to the tracking device, connect FMX640 to computer and open the required configurator application. Select your device and follow instructions below:
On this page, you will be able to find information about the gerenal configuration and connection of DSM camera with the FMX640 tracking device. Information about different parameters required to set up the DSM camera are also described in this page. To start off, firstly follow the instructions on how to connect DSM camera with the FMX640 device, once the camera is connected to the tracking device, connect FMX640 to computer and open the required configurator application. Select your device and follow instructions below:
[[File:DSM server.jpg|300px]]
[[File:DSM server.jpg|300px]]
==DSM configuration for FMx650==
'''(!) Required firmware version - 03.00.14.Rev.114'''. [[DSM_Firmware_errata|Firmware errata.]]
*Make sure '''Data Protocol''' is set to [[Codec#Codec_8_Extended | Codec 8 Extended]]
[[Image:Data_protocol.gif|300px]]
*In ''RS232 \ RS485 settings tab'', make sure to enable '''Camera interface''' by "Enable", and select '''DSM''' in the Mode drop-down menu, afterwards '''DSM COM1''' and '''Camera I/O''' should appear in the tab list.
[[Image:DSM config.gif|600px]]
*Make sure to change '''Camera I/O''' camera state '''Priorities''' to ''Low''
'''
[[File:DSM IO.gif|500px]]
'''
*In appeared ''DSM COM1'' tab, make sure to '''configure everything by your needs''', and do not forget to complete the '''"Domain"''' and '''"Port"''' settings in ''File upload settings''
[[File:DSM COM1.png|500px]]
*'''''NOTE:''''' ''This is a base setup for the device to work properly. Other device configuration is made according to your needs.
===Connecting two cameras simultaneously for FMx650===
------------------
The new feature for FMx650 DSM configuration, which is available from '''03.00.14.Rev.114 iCamera''' allows you to connect two of your cameras at once. Method for connection and configuration stays the same, for this you are only required to choose '''two''' cameras in '''"RS232 \ RS485"''' tab from the configurator.
In the new functionality, you are able to connect any combo of the cameras by your wish, as an example: you are able to connect ''DSM/Dualcam'', ''DashCam/DualCam'', ''DSM/DSM'', ''DualCam/DualCam'' and etc.
[[File:Twincamera.gif|500px]]
==General settings==
==General settings==
[[File:Dsm drowsiness.jpg|300px]]
[[File:Dsm drowsiness.jpg|300px]]
*Activation - Enables or disables Drowsiness function, Sound type of each event can also be changed (0,1 or 2 types).
*Activation - Enables or disables Drowsiness function, Sound type of each event can also be changed (0,1,2 or 3 (voice) types).
*Vibration - Upon Drowsiness event activation, vibration can also be activated, this parameter also has sensitivity setting 1-3 (1- lowest, 3 - highest).
*Vibration - Upon Drowsiness event activation, vibration can also be activated.
*Automatic transmit - Transmits images/audio to the server when the event is active. Also has working speed parameter which sets the minimum required speed for the event to become enabled, leave 0 for this setting to be off.
*Sensitivity - this parameter is for the Drowsiness sensitivity setting 1-3 (1- lowest, 3 - highest).
*Automatic transmit - Transmits images to the server when the event is active. Also has working speed parameter which sets the minimum required speed for the event to become enabled, leave 0 for this setting to be off.
==Distraction==
==Distraction==
[[File:Dsm distraction.jpg|300px]]
[[File:Dsm distraction.jpg|300px]]
*Activation - Enables or disables Distraction function, Sound type of each event can also be changed (0,1 or 2 types).
*Activation - Enables or disables Distraction function, Sound type of each event can also be changed (0,1,2 or 3 (voice) types).
*Vibration - Upon Distraction event activation, vibration can also be activated, this parameter also has sensitivity setting 1-3 (1- lowest, 3 - highest).
*Vibration - Upon Distraction event activation, vibration can also be activated.
*Automatic transmit - Transmits images/audio to the server when the event is active. Also has working speed parameter which sets the minimum required speed for the event to become enabled, leave 0 for this setting to be off.
*Sensitivity - this parameter is for the Distraction sensitivity setting 1-3 (1- lowest, 3 - highest).
*Automatic transmit - Transmits images to the server when the event is active. Also has working speed parameter which sets the minimum required speed for the event to become enabled, leave 0 for this setting to be off.
==Phone==
==Phone==
[[File:Dsm phone.jpg|300px]]
[[File:Dsm phone.jpg|300px]]
*Activation - Enables or disables Phone function, Sound type of each event can also be changed (0,1 or 2 types).
*Activation - Enables or disables Phone function, Sound type of each event can also be changed (0,1,2 or 3 (voice) types).
*Vibration - Upon Phone event activation, vibration can also be activated, this parameter also has sensitivity setting 1-3 (1- lowest, 3 - highest).
*Vibration - Upon Phone event activation, vibration can also be activated.
*Automatic transmit - Transmits images/audio to the server when the event is active. Also has working speed parameter which sets the minimum required speed for the Phone event to become enabled, leave 0 for this setting to be off.
*Sensitivity - this parameter is for the Phone sensitivity setting 1-3 (1- lowest, 3 - highest).
*Automatic transmit - Transmits images to the server when the event is active. Also has working speed parameter which sets the minimum required speed for the Phone event to become enabled, leave 0 for this setting to be off.
==Smoking==
==Smoking==
[[File:Dsm smoking.jpg|300px]]
[[File:Dsm smoking.jpg|300px]]
*Activation - Enables or disables Smoking function, Sound type of each event can also be changed (0,1 or 2 types).
*Activation - Enables or disables Smoking function, Sound type of each event can also be changed (0,1,2 or 3 (voice) types).
*Vibration - Upon Smoking event activation, vibration can also be activated, this parameter also has sensitivity setting 1-3 (1- lowest, 3 - highest).
*Vibration - Upon Smoking event activation, vibration can also be activated.
*Automatic transmit - Transmits images/audio to the server when the event is active. Also has working speed parameter which sets the minimum required speed for the Smoking event to become enabled, leave 0 for this setting to be off.
*Sensitivity - this parameter is for the Smoking sensitivity setting 1-3 (1- lowest, 3 - highest).
*Automatic transmit - Transmits images to the server when the event is active. Also has working speed parameter which sets the minimum required speed for the Smoking event to become enabled, leave 0 for this setting to be off.
==Yawning==
==Yawning==
[[File:Dsm yawning.jpg|300px]]
[[File:Dsm yawning.jpg|300px]]
*Activation - Enables or disables Yawning function, Sound type of each event can also be changed (0,1 or 2 types).
*Activation - Enables or disables Yawning function, Sound type of each event can also be changed (0,1,2 or 3 (voice) types).
*Vibration - Upon Yawning event activation, vibration can also be activated, this parameter also has sensitivity setting 1-3 (1- lowest, 3 - highest).
*Vibration - Upon Yawning event activation, vibration can also be activated.
*Working speed - Working speed parameter which sets the minimum required speed for the Smoking event to become enabled, leave 0 for this setting to be off. '''Note:''' This parameter does not have Automatic transmit parameter, therefore, upon activation, this event is not going to be configured to send images/audio to the server, however this setting can be activated in '''Event settings''' under Automatic transmit (Global) parameter.
*Sensitivity - this parameter is for the Yawing sensitivity setting 1-3 (1- lowest, 3 - highest).
*Working speed - Working speed parameter which sets the minimum required speed for the Smoking event to become enabled, leave 0 for this setting to be off. '''Note:''' This parameter does not have Automatic transmit parameter, therefore, upon activation, this event is not going to be configured to send images/audio to the server, however this setting can be activated in '''Event settings''' under Automatic transmit (Global) parameter.
==File upload settings==
==File upload settings==
*Image sending trigger - Triggers can be set in order to activate image sending. Crash/Towing/Idling/Geofence/Unplug/Green driving are actual features of the FMX640 family devices and are configured under '''[[FMC640_Features_settings | Features]] / [[FMC640_Accelerometer_Features_settings | Accelerometer Features]] / [[FMC640_Manual_Geofence_zones | Geofence]] / [[FMC640_Trip/Odometer_settings | Trip/Odometer]]''' Tabs.
*Image sending trigger - Triggers can be set in order to activate image sending. Crash/Towing/Idling/Geofence/Unplug/Green driving are actual features of the FMX640 family devices and are configured under '''[[FMC640_Features_settings | Features]] / [[FMC640_Accelerometer_Features_settings | Accelerometer Features]] / [[FMC640_Manual_Geofence_zones | Geofence]] / [[FMC640_Trip/Odometer_settings | Trip/Odometer]]''' Tabs.
[[Category:DSM test]]
==Crash Detection Functionality using DOUT==
'''The crash detection feature''' is a crucial capability provided by our device. It enhances evidential documentation through video or photo evidence in the event of a crash. However, activating this functionality necessitates a direct connection of the camera to a power source. Nonetheless, such a direct connection can lead to '''battery drainage'''.
To circumvent this issue, we recommend utilizing DOUT and a relay for connection. This setup enables control via SMS or GPRS command, or through predefined scenarios within our device. By activating DOUT post-ignition, the camera receives power, allowing it to function and record evidence even after the ignition is turned off following a crash. '''For your convenience, the connection scheme can be found here: [[DSM First Start]]'''
'''It is important to note that in the event of a fatal crash where fatalities may occur,''' we cannot guarantee the retrieval of video or photo evidence due to the severity of the accident. Moreover, both the camera and the device itself may sustain irreparable damage in such instances
[[Category:DSM]]