Difference between revisions of "ECAN02"
From Wiki Knowledge Base | Teltonika GPS
m (Protected "ECAN02" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))) |
|||
| Line 172: | Line 172: | ||
==External Links== | ==External Links== | ||
[https://teltonika-gps.com/products/trackers/can-obd-data/ecan02 ECAN02 Teltonika] | [https://teltonika-gps.com/products/trackers/can-obd-data/ecan02 ECAN02 Teltonika] | ||
| + | |||
| + | [[Category:CAN Trackers & Adapters]] | ||
Revision as of 12:23, 12 April 2023
Main Page > CAN Trackers & Adapters > ECAN02
ECAN02 is contactless adapter used to read vehicle CAN Bus data. ECAN02 adapter should be used in combination with:
- LV-CAN200
- ALL-CAN300
- FMB140, FMB150, FMC150, FMM150
- FMB640, FMB630, FM6320, FM6300 to read J1939 CAN data.
It reads can-bus data through the isolation of wires without damaging them and forwards signals to the tracking device.
Features
- ECAN02 collects vehicle data from CAN bus without damaging the wires
- Powered from an on-board power source
- Reads the signals through the isolation of CAN bus wires
- Easy to install and operate
Technical features
| PARAMETER | VALUE | ||||
|---|---|---|---|---|---|
| Minimum | Typical | Typical | Maximum | Unit | |
| Supply Voltage | |||||
| Supply Voltage (Recommended Operating Conditions) | +10 | +12 | +24 | +30 | V |
| Current Consumption | |||||
| Working Mode | 7.6 | mA | |||
| Sleep Mode | 1.7 | mA | |||
| Operating Temperature | |||||
| Operating Temperature | -25 | +85 | °C | ||
| Protection | |||||
| Internal resettable fuse (max 33 V) | 750 | mA | |||
- Dimensions 39 x 12 x 19 mm
- CAN-BUS speeds up to 1000 kb/s
- Fuse is protecting devices from high current peaks. If the voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and the current value will increase accordingly.
Pinout
| PIN NUMBER | PIN NAME |
DESCRIPTION |
|---|---|---|
| 1 | CAN L | (Blue) Connect to CAN L input of CAN BUS converter |
| 2 | CAN H | (White/Blue) Connect to CAN H input of CAN BUS converter |
| 3 | VCC | (RED) Power supply (10-30) V DC (+) |
| 4 | GND (-) | (Black) Ground wire (10-30) V DC (-) |
Wiring scheme
Setup ECAN02
- Gently open ECAN02 cover using plastic pry tool from both sides.
- Remove backing material on one side of double-sided adhesive tape.
- Glue double-sided adhesive tape to casing.
- Remove backing material on double-sided adhesive tape.
- Insert CAN wires. Please make sure that correct slots are used (CAN High/CAN Low).
- Close the device.
- Device is ready-to-use.
_01.png)
_02.png)
_03.png)
_04.png)
_05.png)
_06.png)
_07.png)
ECAN02 Certification & Approvals
Nomenclature, classification codes
FAQ
- How to install ECAN02 with LV-CAN200/ALL-CAN300 using:
- FMB110
- FMB120
- FMB122
- FMB125
- FMB130
- FMC125
- FMC130
- FMC13A
- FMM125
- FMM130
- FMM13A
- FMB225
- FMB230
- FMC225
- FMC230
- FMM230
Product Change Notifications
ECAN02 Product Change Notifications
