FMC640 Thermograph

From Wiki Knowledge Base | Teltonika GPS
Main Page > EOL Products > FMC640 > FMC640 Manual > FMC640 Thermograph

Introduction

With an increasing demand for cold-chain supply chains, Teltonika is offering the ability to monitor real-time information from freezer trailer thermographs. Each thermograph has an RS232 communication line where FMC640 devices can connect via COM1/COM2 port of the device. The solution is easy to install and configure. This allows you to monitor the main information of the freezer trailer such as Temperature, Fridge door status, Alarms, etc., and generate events according to your needs. For more information please refer to the installation manual below.

NOTE: this feature is available from FW ver. 01.02.23.Rev.00

Supported Thermographs

FMC640 can be connected to Euroscan, DataCold600, Transcan2, TouchPrint thermographs.

Refer to the table below to see which freezers use which thermograph:

Thermograph Type
Freezer Type Euroscan DataCold600 Transcan2 TouchPrint/TouchLog
Carrier + + - -
ThermoKing +
- + +

RS-232 Interface

RS-232 supports full-duplex communication which means the data can be both sent and received at the same time as they use separate transmission lines. Most of the modes are the same as for FMC640. When entering Sleep or Deep sleep RS-232 will be powered off. FMC640 RS-232 connection diagram is shown in the figure below:

FMX640 and RS232 illustration v1.2.png

Installation guide

TouchPrint/TouchLog

506581 Thermograph Touchprint.png

TouchPrint pinout:

517441 TOUCHPRINT PINOUT.jpg

No configuration is necessary.

If the equipment does not receive information from the thermographer, the speed of the port accessing the configuration menu:

Keep the blue and red buttons pressed at the same time. "Enter PIN code" is displayed on the screen, enter pin "1111" by pressing the blue button four times. Travel for the options with the red button.

The ENG Display> OFF option must be ON, change its value with the keys ◄ and ►. Once switched to ON, keep scrolling through the options until you find Baud Rate> 9600. The value should be 9600, otherwise, adjust the speed by moving the cursor with the ◄ and ► keys, and adjust the speed with the keys ▲ and ▼.



TouchLog pinout:

517635 TOUCHPLOG PINOUT V1.1.jpg




AVL IDs for Touchprint:

Parameter name Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Setpoint 1 Setpoint 2 Setpoint 3
AVL ID 10695 10696 10697 10698 10699 10700 10701 10702 10703

Configuration: No configuration is necessary.

See ThermoKing Configuration.

Carrier Datacold 600

To properly use DataCold 600 with FMX640 these steps must be followed:

  • In FMX640 RS232 settings DataCold mode is selected and Baudrate set to 38400
  • Partner mode enabled on DataCold 600



511336 Thermograph data cold colour .png


To enable Partner mode on DataCold 600:

  1. Press and hold the green button for 4 seconds
  2. Insert password. Default password - 1111
  3. Press the blue button to open 11 communication settings
  4. Press the green button to select edit action
  5. 11.1.0 Com1 Port settings should be opened, then press the green button again
  6. Then search for Partner protocol and press the green button to accept changes



Important note - RX and TX are inverted via the RS-232 connection. Scheme to properly manage DataCold 600 RS232 connection: Pinout of DataCold600 517440 DataCold PINOUT.jpg

Available parameters (AVL IDs) with DataCold 600:

Parameter name Zone 1 Compartment state Zone 1 Compartment mode Zone 1 Return Air Sensor Zone 1 Supply Air Sensor Zone 1 Set Temperature Zone 1 Evaporator temperature Zone 2 Return Air Sensor Zone 2 Supply Air Sensor Zone 2 Set Temperature Zone 3 Compartment state Zone 3 Compartment mode Zone 3 Set Temperature
AVL ID 10045 10046 10047 10048 10049 10050 10056 10057 10058 10063 10064 10067
Parameter name Speed mode Ambient Air Temperature Compressor Config Installation Serial Analog Input 1-3 Manufacturer ID Battery State Flags Fuel state flags Maintenance 1-5 Hours Run Mode Error Codes Temperature Probe 1-6
AVL ID 10071 10350 10353 10356 10468-10470 10472 10473 10474 10475-10479 10480 10639 10644-10649



Run mode explanation:

Run mode StartStop Continious CycleCentry Unknown/Now available
Value (HEX) 0 1 2 7



Fuel and Battery state flag explanation:

Fuel/Battery Flag Status Available Error Alarm Digital sensor
Enum (bit field) value 0 1 2 3

Euroscan

To properly use Euroscan with FMX640 these steps must be followed:

  • In FMX640 RS232 settings Euroscan mode is selected and Baudrate set to 38400
  • Partner mode enabled on Euroscan



511336 Thermograph data cold colour .png


To enable Partner mode on Euroscan :

  1. Press and hold the green button for 4 seconds
  2. Insert password. Default password - 1111
  3. Press the blue button to open 11 communication settings
  4. Press the green button to select edit action
  5. 11.1.0 Com1 Port settings should be opened, then press the green button again
  6. Then search for Partner protocol and press the green button to accept changes



Important note - RX and TX are inverted via the RS-232 connection. Scheme to properly manage Euroscan RS232 connection: Pinout of DataCold600 517440 DataCold PINOUT.jpg

Available parameters (AVL IDs) with Euroscan :


External Sensor Temperature 1 External Sensor Temperature 2 External Sensor Temperature 3 External Sensor Temperature 4 External Sensor Temperature 5 External Sensor Temperature 6 Digital Sensor 1 Digital Sensor 2 Digital Sensor 3 Digital Sensor 4
484 485 486 487 488 489 10464 10465 10466 10467

Configuration

Make sure the FMC640 device is configured to receive data from “Transcan2 Reefer”, "Touchprint Reefer", "Euroscan: or "DataCold Reefer". To do this, enter the configurator window, select the RS232 \ RS485 section displayed in the screenshots below, and configure accordingly (COM1/COM2 Settings, Mode “Transcan2 Reefer”, "Touchprint Reefer", "Euroscan"or "DataCold Reefer", Baudrate: Default)

RS-232 refer.png

DataCold Reefer

To configure "DataCold Reefer" I/O parameters, please select "Reefer IO": ReeferIO.png

Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to Reefer IO data sending parameters.

TK Transcan2 Reefer

To configure "Transcan2 Reefer" I/O parameters, please select "TK Transcom IO": TranscanIO.png

Data sending parameters (AVL ID) used for "Transcan2 " are these: 10683 - 10694. For more in-depth information, please refer to Transcan IO data sending parameters

Euroscan IO

To configure "Euroscan refeer" I/O parameters select "Euroscan IO": EuroScanIO.png

Data sending parameters (AVL ID) used for "Euroscan" are these: 484-489 and 10464-10467. For more in-depth information, please refer to Euroscan IO data sending parameters.

TK Touchprint/Touchlog I/O

To configure "Touchprint Reefer" I/O parameters select "TK Touchprint IO":

TouchprintIO.png

Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to Touchprint IO data sending parameters.


Codec 8 Extended should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.