Changes

55,084 bytes added , 08:02, 22 August 2019

Created page with "Easy steps to install and configure following CAN adapters on {{{model|FMB1YX}}} device: * LV-CAN200 * ALL-CAN300 * CAN-CONTROL * SIMPLE-CAN * MINI-CAN __..."

Easy steps to install and configure following CAN adapters on {{{model|FMB1YX}}} device:
* [[LV-CAN200]]
* [[ALL-CAN300]]
* [[CAN-CONTROL]]
* [[SIMPLE-CAN]]
* [[MINI-CAN]]

__TOC__

==Installing CAN adapter with {{{model|FMB1YX}}} device==
===Installing LV-CAN200/ALL-CAN300/CAN-CONTROL===

You can watch [[LV-CAN200]]/[[ALL-CAN300]] installation video in our YouTube channel [https://youtu.be/V9RTdSy1E8w '''here'''] or follow connection instructions below.
====Tools needed for installation====
* [[LV-CAN200]]/[[ALL-CAN300]]/[[CAN-CONTROL]]
* Connection scheme (Please contact Teltonika Sales Representative and provide information about '''vehicle manufacturer''', '''model''' and '''year'''.
* {{{model|FMB1YX}}} device
* Pliers
* Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)
* Plastic pry tool
* Zip ties

====Installation steps====
# Be ready with a vehicle '''connection scheme''' that you have received from a Teltonika Sales Representative.
# '''Check the scheme''' for the current vehicle connection. Look for connectors matching '''PINs numbers''' and colors (may be different) according to connection scheme.
# Connect CAN adapter with {{{model|FMB1YX}}}:
## Connect CAN adapter '''PIN 6''' '''(Rx)''' to '''INPUT 6''' of {{{model|FMB1YX}}}.
## Connect CAN adapter '''PIN 5''' '''(Tx)''' to '''INPUT 5''' of {{{model|FMB1YX}}}.
# Connect CAN adapter '''CAN wires (CAN L, CAN H)''' as specified in connection scheme.<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap CAN L and CAN H lines. Not all CAN adapter wires may be used in vehicle.</td></table>
# Connect CAN adapter '''positive''' and '''ground''' wires to the vehicle power supply lines or near {{{model|FMB1YX}}} power wires.<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap power supply lines. Make sure that voltage does not exceed 30V.</td></table>
# Switch vehicle '''ignition to ACC''' position. CAN adapter '''LED diode''' on the back should start '''blinking'''.
# Configure CAN adapter to read CAN bus data or control vehicle by setting its '''program number''' - [[{{{model|FMB1YX}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]
 
[[File:CAN_adapter_connection_example_updated.png|1000px|none|thumb|LV-CAN200/ALL-CAN300 connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.]]
[[File:Can-control_connection_example_updated.png|1000px|none|thumb|CAN-CONTROL connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.]]
 
===Installing LV-CAN200/ALL-CAN300 + SIMPLE-CAN===
----
You can watch [[LV-CAN200]]/[[ALL-CAN300]] + [[SIMPLE-CAN]] installation video in our YouTube channel [https://youtu.be/V9RTdSy1E8w?t=356 '''here'''] or follow connection instructions below.
====Tools needed for installation====
* [[LV-CAN200]]/[[ALL-CAN300]]
* Connection scheme (Please contact Teltonika Sales Representative and provide information about '''vehicle manufacturer''', '''model''' and '''year'''.
* [[SIMPLE-CAN]] (Used for contactless connection. If '''two CAN lines''' need to be connected, '''two SIMPLE-CAN's''' must be used.)
* {{{model|FMB1YX}}} device
* Pliers
* Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)
* Plastic pry tool
* Zip ties

====Installation steps====
# Follow the same '''1, 2, 3''' installation steps as with [[{{{model|FMB1YX}}}_CAN_adapters#Installation_steps| LV-CAN200/ALL-CAN300/CAN-CONTROL installation]].
# Connect the appropiate CAN bus pair of wires between CAN adapter and [[SIMPLE-CAN]]:
#: If '''CAN1 line''' need to be connected as specified in connection scheme:
## Connect CAN adapter '''CAN1 L''' to '''CAN L''' of [[SIMPLE-CAN]].
## Connect CAN adapter '''CAN1 H''' to '''CAN H''' of [[SIMPLE-CAN]].
#: If '''CAN2 line''' need to be connected as specified in connection scheme:
## Connect CAN adapter '''CAN2 L''' to '''CAN L''' of [[SIMPLE-CAN]].
## Connect CAN adapter '''CAN2 H''' to '''CAN H''' of [[SIMPLE-CAN]].<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap CAN L and CAN H lines. Not all CAN adapter wires may be used in vehicle.</td></table>
# Fasten [[SIMPLE-CAN]] '''between vehicle CAN bus wires''' according to the connection scheme. '''It doeasn't matter which wire is on which side.'''[[File:SIMPLE-CAN_connection.gif|none]]
# Connect CAN adapter '''positive''' and '''ground''' wires to the vehicle power supply lines or near {{{model|FMB1YX}}} power wires.<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap power supply lines. Make sure that voltage does not exceed 30V.</td></table>
# Switch vehicle '''ignition to ACC''' position.
# [[SIMPLE-CAN]] '''LED will shine continously''' so device awaits for '''calibration'''.<div><ul><li style="display: inline-block;">[[File:SIMPLE-CAN_calibration.gif|none|thumb|'''Press the switch shortly''' and wait for the LED to start blinking '''every one second'''. ]]</li><li style="display: inline-block;">[[File:SIMPLE-CAN after calibration.gif|none|thumb|Automatic calibration process takes up to 10 seconds depending on the vehicle model. Device is calibrated properly then the LED is blinking '''every 2 seconds'''.]]</li></ul></div><table><td>[[File:Alert.png|50px|left|link=]]</td><td>If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.</td></table>
# Configure CAN adapter to read CAN bus data by setting its '''program number''' - [[{{{model|FMB1YX}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]
 
[[File:Can_adapter%2Bsimple-can_connection_example_updated.png|1000px|none|thumb|LV-CAN200/ALL-CAN300 + SIMPLE-CAN connection example. This is not a connection diagram for your vehicle. Follow LV-CAN200/ALL-CAN300 connection scheme suitable for your vehicle.]]
 
==CAN Adapter Configuration==

===CAN Adapter program number selection===
----
CAN Adapter must be set to program number which depends on the vehicle model. '''Needed program number is always written on CAN Adapter mounting scheme.''' In order to be able to enter program number in adapter '''Software date of CAN adapter must be newer than connection scheme date'''.
CAN adapter Software date can be checked:
* Via [[{{{model|FMB1YX}}}_Status_info#CAN_Adapter_Info|Teltonika Configurator→Status→CAN Adapter]]
* Via SMS command - [[FMB_lvcangetinfo|lvcangetinfo]]

The number of digits required to enter correct Program No. may vary depending on the Software and manufacture date of your CAN Adapter:
* [[LV-CAN200#Adapter_changes|LV-CAN200 adapter changes]]
* [[ALL-CAN300#Adapter_changes|ALL-CAN300 adapter changes]]

====Entering via SMS command====
----
Required conditions:
* CAN adapter properly connected to {{{model|FMB1YX}}} device

CAN adapter program number can be set remotely, using SMS command.
Send following '''SMS command''' to {{{model|FMB1YX}}} device:
* If you have set SMS login and password: <code>login pass lvcansetprog X</code>
* If SMS login and password are not set leave two spaces before command: <code>  lvcansetprog X</code>
Command example: <code>  lvcansetprog 11434</code> 
SMS response: <code>LVCAN ProgNum: 11434</code>

If during SMS command {{{model|FMB1YX}}} was in following Sleep mode:
* [[{{{model|FMB1YX}}}_Sleep_modes#GPS_Sleep_mode|GPS Sleep]] - Program No. will be set immediately.
* [[{{{model|FMB1YX}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep]] - Program No. will be set after device wake up.
* [[{{{model|FMB1YX}}}_Sleep_modes#Online_Deep_Sleep_mode|Online Deep Sleep]] - Program No. will be set immediately.
* [[{{{model|FMB1YX}}}_Sleep_modes#Ultra_Deep_Sleep_mode|Ultra Deep Sleep]] - Program No. will be set after device wake up.

====Entering via Teltonika Configurator====
----
Required conditions:
* CAN adapter properly connected to {{{model|FMB1YX}}} device

CAN adapter program number can be set via '''[[Teltonika Configurator]] → (1) CAN Adapter → (2) Program Number'''. When program number is entered press [[File:Save_to_device.png|25px|link=]] '''(3) Save to device''' button that saves the entered program number into {{{model|FMB1YX}}}.
 
[[Image:FMC125 Can adapter conf.png|700px]]
 
====Entering manually====
----
Required conditions:
* CAN adapter properly connected to {{{model|FMB1YX}}} device
* Vehicle ignition must be ON

Depending on used CAN Adapter, length of setup sequence will vary.

Steps to set program number:
[[Image:Fmb120_adapter_led.png|300px|right|thumb|LV-CAN200, ALL-CAN300 back]][[File:Can_control_back-2.png|300px|right|thumb|CAN-CONTROL back]]
{| class="wikitable" style="width:70%;"
|+
|-
| rowspan="5" style="border: 1px solid #0054A6; background: white; color: #0054A6; text-align: center; width:10%;" | For ALL-CAN300 LV-CAN200 3 digit
| rowspan="6" style="border: 1px solid #0054A6; background: white; color: #0054A6; text-align: center; width:10%;" | For ALL-CAN300 LV-CAN200 4 digit
| rowspan="7" style="border: 1px solid #0054A6; background: white; color: #0054A6; text-align: center; width:11%;" | For LV-CAN200 CAN-CONTROL 5 digit
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white; width:38%;" |1. Hold SWITCH down until LED stars blinking.
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |2. Release the SWITCH.
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |3. Then LED starts blinking and counting first digit of program number (one blink means digit 1, two blinks mean digit 2 etc). To stop counter, push SWITCH.
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |4. Release the SWITCH, then LED starts blinking and counting second digit of program number. To stop counter, push SWITCH.
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |5. Release the SWITCH, then LED starts blinking and counting third digit on program number. To stop counter, push SWITCH.
|-
| rowspan="2" style="border: 1px solid white; border-bottom: 1px solid #0054A6; background: white;" |
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |6. Release the SWITCH, then LED starts blinking and counting fourth digit on program number. To stop counter, push SWITCH.
|-
| style="border: 1px solid white; border-bottom: 1px solid #0054A6; background: white;" |
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |7. Release the SWITCH, then LED starts blinking and counting fifth digit on program number. To stop counter, push SWITCH.
|-
| colspan="3" style="border: 1px solid #0054A6; background: white; color: #0054A6; text-align: center;" | All Devices
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |8. Release SWITCH, if programming is successful LED will blink 10 times.
|}

==={{{model|FMB1YX}}} CAN Adapter parameters configuration===
----
====Teltonika Configurator====
CAN Adapter configuration can be performed using [[Teltonika Configurator]] via '''Micro-USB cable''' or '''Blue-tooth connection''' when CAN Adapter is connected to the vehicle. 
When {{{model|FMB1YX}}} is connected to the CAN Adapter, user can see all information that is received from the vehicle in [[Teltonika Configurator]]''' → Status → CAN Adapter''' tab or [[Teltonika Configurator]]''' → CAN Adapter''' section. In '''Status → CAN Adapter''' tab you can see information about CAN adapter and its readable parameters. In '''CAN Adapter''' section you can configure CAN Adapter and see incoming CAN bus data highlighted by '''green''' background color. Incoming data in both sections is automatically refreshed every 5 seconds. CAN bus data which should be readable from your vehicle is provided in "CAN Adapter supported vehicles list", which you can get from Teltonika Sales Representative. 
The CAN Adapter I/O element can be configured like any other I/O element in [[Teltonika Configurator]]. All information about I/O element parameters description is in section [[{{{model|FMB1YX}}} I/O settings|I/O settings]].
 
[[Image:FMC125 can conf example.png|800px|none]]
 
When using offline configuration method user can select which CAN data (according to vehicle) will be sent directly to the server without connection to adapter.

=====Send data with 0, if ignition is off=====
----
Depending on CAN Adapter I/O parameters and ignition status, {{{model|FMB1YX}}} can send locked (last known) CAN Adapter I/O and active (real time) parameters values or reset values to 0. When ignition is off, CAN Adapter I/O parameters values sent to server are:

{| class="wikitable" style="width:40%;"
|+
! style="width: 25%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | CAN Adapter I/O element
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | Status
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Vehicle Speed
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Accelerator pedal position
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Total fuel used
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Fuel level (liters)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Engine RPM
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Total mileage
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Fuel level (%)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Program number
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Module ID
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Engine Work Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Engine Work Time (counted)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Total Mileage (counted)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Fuel Consumed (counted)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Fuel Rate
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Program number
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | AdBlue Level (%)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | AdBlue Level (liters)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Engine Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Engine Temperature
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Axle 1 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Axle 2 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Axle 3 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Axle 4 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Axle 5 Load
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Control State Flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Agricultural Machinery Flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Harvesting Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Area of Harvest
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Mowing Efficiency
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Grain Mown Volume
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Grain Moisture
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Harvesting Drum RPM
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Gap Under Harvesting Drum
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Security State Flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Tachograph Total Vehicle Distance
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lock
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Trip Distance
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Tachograph Vehicle Speed
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | reset
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Tachograph Driver Card Presence
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver1 States
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver2 States
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver1 Continuous Driving Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver2 Continuous Driving Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver1 Cumulative Break Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver2 Cumulative Break Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver1 Selected Activity Duration
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver2 Selected Activity Duration
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver1 Cumulative Driving Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver2 Cumulative Driving Time
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | active
|-
|}
 
====SMS Configuration====
----
All CAN Adapter IO elements can be configured remotely via SMS commands.

=====SMS/GPRS Commands=====

CAN Adapters have several dedicated SMS/GPRS commands. 
SMS command structure:
<SMS login><space><SMS password><space><command><space><value>
SMS command [[FMB lvcangetinfo|lvcangetinfo]] example:
* If you have set SMS login and password: <code>login pass lvcangetinfo</code>
* If SMS login and password are not set leave two spaces before command: <code>aalvcangetinfo</code>
 
GPRS commands require [[Codec 12]] protocol.

For more SMS commands please see [[{{{model|FMB1YX}}} SMS/GPRS command list|SMS/GPRS command list]]

{| class="wikitable" style="width:80%;"
|+
! style="width: 25%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | COMMAND
! style="width: 65%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | DESCRIPTION
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | RESPONSE
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcansetprog #
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Set program number to CAN Adapter that is connected to {{{model|FMB1YX}}}. # - three digit number that identity vehicle.
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcansimpletacho #
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Add or remove simpletacho start byte. # - 0 or 1 (0 – don’t add start byte, 1 – add start byte).
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | No
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcangetprog
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Get program number from CAN Adapter that is connected to {{{model|FMB1YX}}}.
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[FMB lvcangetinfo|lvcangetinfo]]
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Get information about connected CAN Adapter
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[FMB_lvcanclear|lvcanclear #]]
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Clear Total Mileage (counted), Engine Work Time (counted), Fuel Consumed (counted) parameters values. # - parameter (0 – Engine work time (counted), 1 – Fuel Consumed (counted), 2 – Vehicle Mileage (counted)).
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | allcanmode
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Turn on ALL-CAN300 mode.
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanmode
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Turn on LV-CAN200 mode.
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[FMB_lvcanfaultcodes|lvcanfaultcodes]]
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Read DTC fault codes
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| colspan="3" style="border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | '''CAN-CONTROL specific commands'''
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanopenalldoors
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Open [unlock] all doors
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanclosealldoors
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Close [lock] all doors
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanopentrunk
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Open [unlock] trunk
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcanturninglights
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | One flash of all turn lights ordered trough accidental / blinking turn light switch
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes
|-

|}

===CAN Adapter State Flags===
----
CAN Adapters receive data about the states of various systems within the vehicle, and send them as flags to {{{model|FMB1YX}}}. {{{model|FMB1YX}}} device stores these flags in hexadecimal format, as one variable. Bellow is a list of kept flags and how to retrieve them. The full list of state flags is stored only by:
* [[ALL-CAN300]]
Only '''security state flags''' are stored by:
* [[CAN-CONTROL]]

{| class="wikitable" style="width:70%;"
|+
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | Property name
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | Size, bytes
! style="width: 40%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | Value bitmasks
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| Control state flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 4
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Byte0 (LSB): 
0x01 – STOP 
0x02 – Oil pressure / level 
0x04 – Coolant liquid temperature / level 
0x08 – Handbrake system 
0x10 – Battery not charging 
0x20 – AIRBAG 
0x40 – EPS (Electric power steering) 
0x80 – ESP (Electronic Stability Program) 
Byte1: 
0x01 – CHECK ENGINE 
0x02 – Lights failure 
0x04 – Low tire pressure 
0x08 – Wear of brake pads 
0x10 – Warning 
0x20 – ABS 
0x40 – Low Fuel 
0x80 – Maintenance required 
Byte2: 
0x01 – ESP 
0x02 – Glow plug indicator 
0x04 – FAP 
0x08 – Electronics pressure control 
0x10 – Parking lights 
0x20 – Dipped headlights 
0x40 – Full beam headlights 
0x80 – Front foglights 
Byte3: 
0x01 – Ready to drive 
0x02 – Cruise control 
0x04 – Automatic Retarder 
0x08 – Manual retarder 
0x10 – Air Conditioning 
0x20 – Rear foglights 
0x40 – Passenger's seat belt 
0x80 – Driver's seat belt 
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Agricultural machinery flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 8
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| Byte0 (LSB): 
0x01 – Mowing 
0x02 – Grain release from hopper 
0x04 – First front hydraulic turned on 
0x08 – Rear Power Take-Off turned on 
Byte1: 0x01 – Excessive play under the threshing drum 
0x02 – Grain tank is open 
0x04 – 100% of Grain tank 
0x08 – 70% of Grain tank 
0x10 – Drain filter in hydraulic system of drive cylinders is plugged 
0x20 – Pressure filter of drive cylinders hydraulic system is plugged 
0x40 – Alarm oil level in oil tank 
0x80 – Pressure filter of brakes hydraulic system is plugged 
Byte2: 0x01 – Oil filter of engine is plugged 
0x02 – Fuel filter is plugged 
0x04 – Air filter is plugged 
0x08 – Alarm oil temperature in hydraulic system of chassis 
0x10 – Alarm oil temperature in hydraulic system of drive cylinders 
0x20 – Alarm oil pressure in engine 
0x40 – Alarm coolant level 
0x80 – Overflow chamber of hydraulic unit 
Byte3: 0x01 – Unloader drive is ON. Unloading tube pivot is in idle position 
0x02 – No operator! 
0x04 – Straw walker is plugged 
0x08 – Water in fuel 
0x10 – Cleaning fan RPM 
0x20 – Trashing drum RPM 
0x40 – Pouring chemicals turned on 
0x80 – Conveyor belt turned on 
Byte4: 
0x01 – Salt spreaders drive wheel turned on 
0x02 – Low water level in the tank 
0x04 – First rear hydraulic turned on 
0x08 – Standalone engine working 
0x10 – Right joystick moved right 
0x20 – Right joystick moved left 
0x40 – Right joystick moved front 
0x80 – Right joystick moved back 
 
Byte5: 
0x01 – Brushes turned on 
0x02 – Water supply turned on 
0x04 – Vacuum cleaner 
0x08 – Unloading from the hopper 
0x10 – High Pressure washer (Karcher) 
0x20 – Salt (sand) disperser ON 
0x40 – Low salt (sand) level 
Byte6: 
0x01 – Second front hydraulic turned on 
0x02 – Third front hydraulic turned on 
0x04 – Fourth front hydraulic turned on 
0x08 – Second rear hydraulic turned on 
0x10 – Third rear hydraulic turned on 
0x20 – Fourth rear hydraulic turned on 
0x40 – Front three-point Hitch turned on 
0x80 – Rear three-point Hitch turned on 
Byte7: 0x01 – Left joystick moved right 
0x02 – Left joystick moved left 
0x04 – Left joystick moved front 
0x08 – Left joystick moved back 
0x10 – Front Power Take-Off turned on 
0x20 – Liquid pump turned on 
0x40 – Light signal turned on 
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| Security state flags
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| 8
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| Byte0 (LSB): 
0x01 – CAN1 not connected, require connection 
0x02 – CAN1 not connected, require connection 
0x03 – CAN1 connected 
0x04 – CAN2 not connected, require connection 
0x08 – CAN2 not connected, require connection 
0x0C – CAN2 connected 
0x10 – CAN3 not connected, require connection 
0x20 – CAN3 not connected, require connection 
0x30 – CAN3 connected 
Byte2: 
0x04 – Battery charging 
0x08 – Charging cable connected 
0x10 – Vehicle working mode, 1- business mode, 0 - private mode 
0x20 – Bit appears when any operate button in car was put. This bit is reset if the button is released 
0x40 – Bit appears when immobilizer is in service mode 
0x80 – Immobiliser, bit appears during introduction of a programmed sequence of keys in the car 
Byte3: 
0x01 – The key is in ignition lock 
0x02 – Ignition on 
0x04 – Dynamic ignition on 
0x08 – Webasto 
0x10 – Car closed 
0x20 – Car closed by factory's remote control 
0x40 – Factory-installed alarm system is actuated (is in panic mode) 
0x80 – Factory-installed alarm system is emulated by module 
Byte4: 
0x01 – Parking activated (automatic gearbox) 
0x10 – Handbrake is actuated (information available only with ignition on) 
0x20 – Footbrake is actuated (information available only with ignition on) 
0x40 – Engine is working (information available only when the ignition on) 
0x80 – Reverse is on 
Byte5: 
0x01 – Front left door opened 
0x02 – Front right door opened 
0x04 – Rear left door opened 
0x08 – Rear right door opened 
0x10 – Engine cover opened 
0x20 – Trunk door opened 
Byte6: 
– Low nibble (mask 0x0F value) 
0x01 – Car was closed by the factory's remote control 
0x02 – Car was opened by the factory's remote control 
0x03 – Trunk cover was opened by the factory's remote control 
0x04 – Module has sent a rearming signal 
0x05 – Car was closed three times by the factory's remote control 
– High nibble (mask 0xF0 bit) 
0x80 – CAN module goes to sleep mode 
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Tachograph driver card presence
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| 1
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;"| 0x00 – No driver card 
0x01 – Driver1 card presence 
0x02 – Driver2 card presence 
0x03 – Driver1 and driver2 cards present 
|-
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver 1 states
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 1
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" rowspan=2 | 0xX0 – Break/rest 
0xX1 – Availability 
0xX2 – Work 
0xX3 – Driving 
0x0X – No time-related warning detected 
0x1X – Limit #1: 15 min before 4 1/2 h 
0x2X – Limit #2: 4 1/2 h reached (continuous driving time exceeded) 
0x3X – Limit #3: 15 minutes before optional warning 1 
0x4X – Limit #4: optional warning 1 reached 
0x5X – Limit #5: 15 min before optional warning 
0x6X – Limit #6: optional warning 2 reached 
|-
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Driver 2 states
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 1
|}
 

==LV-CAN200/ALL-CAN300 Important Information==
===Program Number logic change===
Due to the growing number of supported cars, program numbers have exceeded "999". In order to maintain one number format, we are moving from 3-digit to 4-digit program numbers. In new LV-CAN200/ALL-CAN300 firmware (from 2017-09-01) all program numbers that were up to 999 are changed to start from 1000. So that further program numbers would continue the counting with 4-digit numbers. However, all existing program numbers stay the same, but "1" is added to the front. Device still understands the entered 3-digit program number (via SMS/GPRS), it will automatically add "1" before it. If you enter "247" - device number will turn into "1247". In Bootloader only 4-digit format is available, just add "1" to the front of the needed program number.

===Example===
When using older connection schemes where program number displayed as 3-digit program number:
[[Image:Fmb120_can_prog_number.png|600px|none]]

Using LV-CAN200/ALL-CAN300 Bootloader from soft version 2017-09-27 it is necessary to add "1" to the front of program number:
[[Image:Fmb120_can_updater.png|400px|none]]

Aurimas.vanagas

Administrators

1,583

edits

Namespaces

Variants

Views

More

Search

Changes

Template:FMC CAN adapters (view source)

Revision as of 08:02, 22 August 2019

Navigation menu

Personal tools

NAVIGATION

Tools

Categories