From Teltonika Telematics Wiki
Select the needed category:
E-Mobility Trackers
TFT100
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.02.03.Rev.06 1.7.66_B.55.2_R.11
|
2024-01-15
|
- [ADD] Added CAN Debug feature and CAN Log parameter
- [CHN] Increased DOUT duration limit for Overspeeding, Green Driving, Idling features
- [ADD] Added Odometer parameter for UART, RS232 and RS485
- [REM] Removed CAN and RS485 termination resistor management parameter
- [FIX] Fixed Askoll CAN protocol charge voltage and current I/O parameters visibility, removed malfunction indication I/O
- [FIX] Fixed FLEX CAN protocol parameters duplication
- [ADD] Added Ignition ON Counter feature
- [ADD] Added Separate Manual CAN I/O Reset feature and related parameters
- [CHN] Reduced max sensor size to 64 bytes
- [CHN] Moved Manual CAN baudrate parameter to main CAN I/O section
- [CHN] Changed Manual CAN Settings table and simplified CAN protocol settings
- [CHN] Changed device Wiki links to Teltonika-gps
- [FIX] Fixed BLE Custom I/O Low level maximum value to match valid range by firmware
- [REM] Removed wrong parameter (ID: 740 and 741) tool tips
- [ADD] Added Eye Sensors support
- [FIX] Fixed Roaming/Blacklist CSV file import
- [FIX] Fixed Manual CAN request period max range
- [REM] Removed Manual CAN and Manual J1939 parameters option to leave empty field
- [ADD] Added High resolution vehicle distance and Trip Distance CAN ID and I/O to Default J1939 protocol
- [ADD] Added new Askoll CAN protocol I/O's
- [CHN] Changed Manual CAN Commands interface to table
- [REM] Removed ISO6709 I/O
- [FIX] Fixed Tool Tips inaccuracies
- [FIX] Fixed Online vs Offline configuration discrepancies
- [CHN] Changed Manual CAN I/O and Ignition range Low and High level maximum value range
- [FIX] Fixed J1939 Source Address maximum address to 253
- [FIX] Fixed UART Battery temperature Low level maximum value range
- [FIX] Fixed Ultra Deep Sleep naming mismatch
- [ADD] Added SMS Events functionality
- [FIX] Fixed auto answer (HF) wrong parameter values
- [REM] Removed RS485 Mode selection duplication
|
- [CHN] Increased DOUT duration limit for Overspeeding, Green Driving, Idling features
- [ADD] Added CAN Debug feature
- [CHN] Changed 0% battery level voltage to 3.3V
- [ADD] Added battery percentage level to battery info SMS
- [ADD] Added Ignition ON Counter feature
- [ADD] Added protection against network stuck reset when device is working from battery and immobilizer scenario might be activated
- [CHN] Improved CAN data reading operation for each available CAN protocol
- [ADD] Added CAN chip sleep when external power is not available or device is in Ultra Deep Sleep
- [ADD] Added Separate Manual CAN I/O Reset feature
- [ADD] Added new Askoll CAN I/O's
- [ADD] Added watchdog timer for CAN task
- [CHN] Improved DOUT control during device's boot-up
- [FIX] Fixed incorrect CAN SMS/GPRS AVL response
- [ADD] Added High resolution vehicle distance and Trip Distance CAN ID and I/O to Default J1939 protocol
- [REM] Removed ISO6709 I/O
- [FIX] Fixed ignition detection with power voltage higher than 65V
- [FIX] Fixed CAN and UART I/O low level range values
- [ADD] Added SMS Events functionality
- [FIX] Fixed AVL ID 239 (Ignition) value not updating in records
- [FIX] Fixed Auto Geofence text field parameter resetting after device reboot
- [ADD] Added Eye Sensors support
- [CHN] Changed CAN None protocol operation - CAN is not configured, CAN task suspended
- [CHN] Reduced 1-Wire startup delay after wake up from UDS
- [ADD] Added DIN2 status to getio command
- [FIX] Fixed setdigout speed command when GNSS fix is not available
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.01.10.Rev.00 1.6.11 R.39
|
2022.09.09
|
- [CHN]: Changed Default and Minimum CAN Command period. Changed tooltips.
- [ADD]: Add timestamp backup description
- [CHN]: Corrected misleading and outdated tooltips
- [CHN]: Changed TFT100 default configuration.
- [ADD]: Added CAN I/O reset parameter.
- [ADD]: Govecs FLEX (TFT100) changes were merged into 7.0.33 version.
- [ADD]: Added AES128 BLE encryption KEY parameter
- [CHN]: Updated tooltip description for DOUT Deactivation Via DIN
|
- [FIX]: Fixed BLE Sensor Custom IO SMS sending with value NaN and displaying as ASCII in Configurator.
- [FIX]: Fixed device constantly opening and closing GPRS with permanent link if APN is empty in configurator.
- [FIX]: Fixed permanent link not changing protocol after reconfiguration.
- [CHN]: Updated FOTA WEB protocol ID 0x04 => 0x05
- [FIX]: Increased connection interval in order to speed up connection through BLE terminal.
- [FIX]: Fixed POSI command skipping.
- [FIX]: Fixing network stability issues.
- [FIX]: Fixed timestamp not renewing for Eddystone beacons.
- [FIX]: Added condition to prevent closing socket, if GPRS command is received and response was not sent yet.
- [FIX]: Fixed issue, when after pin reconfiguration from DOUT to DIN, DOUT stays ON.
- [FIX]: Fixed periodic CAN command message disabling.
- [FIX]: Fixed Flex CAN protocol reading 0 values after power is cut off.
- [FIX]: Fixed Manual CAN commands periodical sending.
- [CHN]: Changed TFT100 default configuration.
- [CHN]: Increased external queue size to prevent abnormal restarts during BLE scan.
- [ADD]: Added Reset CAN IO values parameter.
- [FIX]: Fixed CAN message sending irregularities.
- [FIX]: Fixed J1939 CAN reading recovery after external power is off.
- [ADD]: Added priority for charger control factory command.
- [FIX]: Fixed a broken GSM connection due to incorrect SIM card selection.
- [FIX]: Fixed FOTA WEB fail when the files requested for download do not exist.
- [FIX]: Fixed lost BLE AES encryption key after reboot.
- [ADD]: Merged Govecs FLEX changes into base. New configuration 7.0.33 created also.
- [FIX]: Fixed DOUT delay after ignition detection.
- [FIX]: Fixed Manual CAN Ignition and Speed I/O‘s timeout issue
- [FIX]: Fixed Manual CAN Speed Source I/O‘s Speed Offset min/max values
- [ADD]: Added AES128 BLE encryption functionality
- [FIX]: Fixed Manual CAN I/O triggers with configured operands
- [FIX]: Fixed GPRS commands sending with TLS encryption
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.01.02.Rev.02 1.6.11_R.30
|
2021.11.03
|
- Parameters for Ignition, Speed extraction from manual CAN messages added.
- Added immobilizer functionality which is not dependent on ignition.
- GNSS source parameter mask changed to allow only valid GNSS modes.
- FLEX protcol functionality added.
- Manual CAN Commands functionality moved to separate tab.
- 120 Ohm resistor settings added for CAN, RS485 variants.
- Last know position parameter added.
- PDOP filter parameters added.
|
- Fixed FW up/downgrade for TFT CAN devices with new Flash component.
- SMS commands updated. Commands will return time with time zone applied.
- Fixed minus temperature calculation.
- PDOP filter added.
- Movement detection tracking fixed.
- GNSS source parameter only available value can be set.
- Added Backup tracker scenario.
- Added speed, ignition source manual CAN functionality.
- Added immobilizer functionality which is not dependent on ignition.
- Updated Manual CAN IO value dispaly. The value is cleared after configuration changed.
- Added FLEX protocol support.
- Added a time guard if BLE scan job is stuck.
- Fixed external voltage value representation in battery SMS command response.
- Added 120 Ohm resistor support.
- Added Last known position parameter added.
|
55.00.14.Rev.00 1.6.11_R.19
|
2021.02.03
|
- Parameter order in IO section was updated.
- Timestamp backup functionality added.
- Added possibility to include additional IOs to eventual crash record.
- Added Endianess, Payload and RTR options to Manual CAN settings.
|
- Added possibility to include additional IOs to eventual crash record
- Fixed DOUT state after immobilizer.
- Fixed double iButton scanning issue for immobilizer after sleep.
- Fixed Crash event value.
- Added battery percentage value to the SMS
- Increased compatible beacons count from 25 to 100.
- Fixed memory leak, when the GPS module is turned on and off frequently.
- Timestamp backup functionality added.
- Improved Manual CAN data reading.
- Beacon detection regarding the timestamp for immobilizer functionality, minimal ignition tmo changed to 5s.
- Added Request DA parameter to Manual J1939 (availability to send request to specific adress).
- Added Payload and RTR parameters to Manual CAN (availability to send requests with data).
- Option to start Manual CAN commands on startup was added.
- Added command .can_dbg:<1/0>, which turn on/off the additional CAN debug functionality.
|
55.00.09.Rev.08 1.6.11_R.14
|
2020.10.16
|
- Added BMS2 I/O parameters to Bosch CAN protocol;
- Added DOUT control via Ignition feature;
- Added Manual J1939 protocol;
- Added permanent link with server feature;
- Added Manual CAN commands functionality;
- Added Falldown functionality with autocalibration;
- Added Battery level I/O parameter;
- Added Battery Charge Mode feature;
- Added Beacon selection with Immobilizer feature;
- Added functionality to hide DOUT selection near all features if DIN is selected;
- Added Manual CAN feature;
- Added Default J1939 protocol support with it's I/O parameters.
|
|
55.00.08.Rev.03 1.5.15_C.003
|
2020.04.10
|
- Optimized Digital Output tool tips;
- Optimized UART panel title to be more accurate;
- Removed duplicated I/O parameters;
- Added RS485 Super Soco protocol;
|
- Added wake up via DIN1 in Ultra Deep Sleep mode functionality;
- Added GoUrban RS485 protocol for Super Soco e-scooter;
- Added new TFT100 hardware support;
|
55.00.06.Rev.01 1.5.0_C.007
|
2020.02.07
|
- Implemented an option to select Analog Input Value Range;
- Optimized default configuration;
- Added DOUT Control Via Call feature;
- Added iButton Read Notification and Immobilizer feature;
- Added On Demand Tracking feature;
- Added new Ignition Source parameters - Accelerometer, DIN1, Power Voltage, CAN;
- Implemented DIN/DOUT selection ability;
- Added Bosch CAN Powertrain and Askoll protocol selection and I/O's;
- Added TFT100 hardware support;
|
- Optimized Askoll specific commands;
- Optimized CAN chip and NAND SPI Chip select synchronization;
|
55.00.05.Rev.00 1.6.11_R.X
|
2020.01.17
|
|
- Optimized iButton Read Notification feature;
- Added DOUT Control Via Call and iButton features;
- Added Immobilizer scenario;
- Added DOUT Control via Call scenario;
- Added new Ignition Source parameters - Accelerometer, DIN1, Power Voltage, CAN;
- Implemented the ability to configure DIN/DOUT;
- Added FOTA WEB support;
- Added Askoll related SMS commands - askoll_unlock, askoll_horn, askoll_tc;
- Optimized data reading through CAN interface;
- Implemented Bosch CAN Powertrain and Askoll protocols;
- Added DOUT protection;
- Added base functionality for all modifications;
- Added TFT100 hardware support;
|
TST100
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.01.10.Rev.00 1.6.11 R.39
|
2022.09.12
|
- [ADD]: Added timestamp backup description.
- [CHN]: Corrected misleading and outdated tooltips.
- [ADD]: Added Hergele scooter protocol.
- [ADD]: Added SIM card tamper protection feature.
|
- [FIX]: Fixed BLE Sensor Custom IO SMS sending with value NaN and displaying as ASCII in Configurator.
- [FIX]: Fixed device constantly opening and closing GPRS with permanent link if APN is empty in configurator.
- [FIX]: Fixed permanent link not changing protocol after reconfiguration.
- [CHN]: Updated FOTA WEB protocol ID 0x04 => 0x05
- [FIX]: Increased connection interval in order to speed up connection through BLE terminal.
- [FIX]: Fixed POSI command skipping.
- [FIX]: Fixing network stability issues.
- [FIX]: Fixed timestamp not renewing for Eddystone beacons.
- [FIX]: Added condition to prevent closing socket, if GPRS command is received and response was not sent yet.
- [ADD]: Added SIM card tamper protection feature.
- [ADD]: Added BT whitelist for Solebe lock.
- [ADD]: Hergele scooter support added.
- [CHN]: Increased external queue size to prevent abnormal restarts during BLE scan.
- [FIX]: Fixed a broken GSM connection due to incorrect SIM card selection.
- [ADD]: HeadLight status in Scooter IO added
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.01.02.Rev.01 1.6.11_R.30
|
2021.11.03
|
- Changed SMS Timezone label.
- GNSS source parameter mask changed to allow only valid GNSS modes.
- Changed scooter speed limits IOs high/low ranges and default values.
- Added Segway Cable Lock I/O elements.
- Changed unauthorized movement buzzer control default values.
|
- SMS commands updated. Commands will return time with time zone applied.
- Added Segway wired lock support.
- Movement detection tracking fixed.
- For GNSS source parameter only available values can be set.
- Fixed Unauthorized Movement event SMS sending.
- Fixed record generation with correct AVL ID for Unauthorized Movement.
|
55.00.22.Rev.00 1.6.11_R.27
|
2021.08.23
|
- Changed GNSS source parameter mask to allow only valid GNSS modes.
- Changed scooter speed limits IOs high/low ranges and default values.
- Changed Data Acquisition tool tips and labels.
- Added Falldown auto calibration parameter.
- Added Unauthorized movement functionality.
- Added Last known position parameter.
|
- Fixed GPS automatic always ON at the start.
- Updated function to wake up the device if it is moved during "Data sending state".
- Fixed I/O Sleep mode element to send an event messages on entering the mode.
- Added Last known position parameter.
- Added pulsedigout command with on/off timeouts in ms and repeats.
- Fixed GNSS Fix status always on after changing GNSS source.
- Updated restricted I/Os by scooter model and fixed battery lock status value.
- Added Unauthorized movement functionality.
- Added Falldown auto calibration support for TST100.
- Changed Battery value SMS text format changed to unsigned int.
- Added Segway MAX autodetection and MC FW update.
- Added Segway ES autodetection and MC FW update.
- Fixed periodic data record generation in order to avoid skipping.
- Updated Segway ES2/4 FW (ESC 4.0.5).
- Added a time guard if BLE scan job is stuck.
- Fixed Unauthorized Movement event SMS sending.
- Fixed record generation with correct AVL ID for Unauthorized Movement.
- Fixed ext voltage value representation in battery SMS command response.
- Fixed scooter speed limits IOs hi/lo ranges check.
- Fixed unauthorized movement buzzer control using default values.
|
55.00.14.Rev.00 1.6.11_R.19
|
2021.02.03
|
- Added Baudrate options.
- Added Battery lock status Scooter IO element.
|
- Added battery percentage value to the SMS.
- Increased compatible beacons count from 25 to 100.
- Fixed memory leak, when the GPS module is turned on and off frequently.
- Changed scooters' IOs filtering depending on protocol.
- Fixed locking behavior during ride.
- Improved Movement detection.
- Segway MAX MC FW was updated to 21.1.0.
- Added Baudrate options.
- Fixed temperature and FW version reading in FitRider e-kick scooters.
- Fixed speed limit function. Added command scsetspdlimt2s for FitRider T2s e-kick scooters.
- Added debug option for sending/receiving FitRider data packets.
- Segway MAX scooters locking sequence changed: when scooter is moving and command to lock the scooter was received, the engine is turned off and after the scooter is fully stopped it is locked.
- Added Battery Lock control command and Battery lock status IO element.
|
55.00.09.Rev.08 1.6.11_R.14
|
2020.10.16
|
- Updated scooter's FW rendering in E-Scooter I/O panel from DEC to HEX;
- Added permanent link with server feature;
- Removed accelerometer's autocalibration parameter;
- Added 3 new I/O parameters - Normal/Eco/Sport speed limit;
- Added BT Status I/O parameter;
|
- Improved BLE lock functionality;
- Added 3 new I/O parameters - Normal/Eco/Sport speed limit;
- Updated Segway MAX kick e-scooter's MC FW version checking functionality;
- Updated scgetbtcode and sclookfor commands;
- Added BT Status I/O parameter;
- Updated Segway MAX MC and BMS FW versions to 21.0.7 and 3.5.6 correspondingly;
- Removed Segway scooter's model detection based on serial number. Make sure to always select the correct scooter's protocol!
- Added SMS/GPRS command for packet's logging - scdbg <arg>; <arg> = 1 - enable, 0 - disable;
- Updated scbuzzerctrl command functionality with Xiaomi kick e-scooter;
- Updated battery overheat detection.
|
55.00.09.Rev.1 1.6.11_R.8
|
2020.06.16
|
- Added permanent link with the server feature
- Implemented Solebe Y905 Bluetooth lock feature with required parameters (Lock status, Lock battery)
- Minor changes
|
- Implemented permanent link with server functionality;
- Added Solebe Y905 Bluetooth lock support;
- Minor changes;
|
Autonomous Trackers
TMT250
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.02.03.Rev.05 1.7.66 B.55.2 R.10
|
2024-01-30
|
- [CHN] Added new AVL ID's SMS events tab
- [FIX] Fixed Online vs Offline configuration discrepancies
- [FIX] Fixed Ultra Deep Sleep naming mismatch
- [FIX] Fixed Tool Tips inaccuracies
- [ADD] Added EYE Sensors support settings and filtering by sensors name and MAC address
- [CHN] Changed device wiki links to teltonika-gps
- [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab
- [FIX] Fixed Roaming operator/Operator Black List .csv file importing
- [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
- [ADD] Added configurable accelerometer sensitivity settings
- [ADD] Added continuous battery charging mode
- [CHN] Changed minimum BLE scan start period value
|
- [CHN] Added possibility to send SMS AVL ID event to few numbers
- [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
- [ADD] Added CSQ level parameter
- [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
- [FIX] Added configurable accelerometer sensitivity options in sleep mode
- [FIX] Fixed ‚btgetlist 3‘ SMS command
- [FIX] Changed battery voltage measurement and charging algorithm
- [ADD] Added EYE Sensor support
- [ADD] BLE Sensors Custom field data are displayed in decimal now
- [FIX] Fixed batteries percentage calculation when voltage is Fully charged
- [FIX] Refactored battery percentage limits checking algorithm
- [FIX] Fixed battery charging status
- [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
- [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
- [FIX] Fixed GSM established LED indication turning off issue
- [CHN] Changed minimum BLE scan start period configuration value.
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.02.03.Rev 05 1.7.66_B.55.2_R.10
|
2023-12-13
|
- [CHN] Added new AVL IDs SMS events tab
- [FIX] Fixed Online vs Offline configuration discrepancies
- [FIX] Fixed Ultra Deep Sleep naming mismatch
- [FIX] Fixed Tool Tips inaccuracies
- [ADD] Added EYE sensors support settings and filtering by sensor's'name and MAC address
- [CHN] Changed device wiki links to teltonika-gps
- [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab.
- [FIX] Fixed Roaming operator/Operator Black list .csv file importing
- [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
- [ADD] Added configurable accelerometer sensitivity settings
- [ADD] Added continuous battery charging mode
- [CHN] Changed minimum BLE scan start period value.
|
- [CHN] Added possibility to send SMS AVL ID event to few numbers
- [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
- [ADD] Added CSQ level parameter
- [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
- [ADD] Added configurable accelerometer sensitivity options in sleep mode
- [FIX] Fixed ‚btgetlist 3‘ SMS command
- [FIX] Changed battery voltage measurement and charging algorithm
- [ADD] Added EYE sensor support
- [ADD] BLE sensors Custom field data are displayed in decimal now
- [FIX] Fixed batteries percentage calculation when voltage is Fully charged
- [FIX] Refactored battery percentage limits checking algorithm
- [FIX] Fixed battery charging status
- [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
- [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
- [FIX] Fixed GSM established LED indication turning off issue
- [CHN] Changed minimum BLE scan start period configuration value.
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.01.02.Rev.01 1.6.11_R.30
|
2021.10.25
|
- Change No Movement/Movement event SMS text
- Added Race Mode feature
|
- Added Race Mode for GNSS data live tracking
- Fixed LED indication stuck when Man-Down Cancel button is pressed
- Fixed FW version display in FOTA WEB
- Fixed possibility to configure forbidden GNSS source via SMS or GPRS
- Fixed fake movement events when Low power mode is used
- Fixed BLE scan stuck when Xiaomi bracelet is used
- Fixed restarts when Beacon on Demand feature is used for longer time
- Fixed Alarm call delay issue
- Fixed FW update issue with XT26G01CWSIGT flash
- Added XT26G01CWSIGT and GD5F1GQ5UE NAND flash support
- Changed minimum charging temperature from -10°C to 1°C
- SMS commands will return time with applied time zone
- The maximum battery charging temperature changed from 50°C to 45°C
- Maximum operating temperature changed from 65°C to 59°C
|
55.00.21.Rev.00 1.6.11_R.26
|
2021.08.10
|
- 'Data Acquisition' tool tips and labels changed.
- Changed BLE 'Update frequency' name and tool tips.
- Fixed 'Beacon on demand' labels.
|
- Added possibility to Enable or Disable Mandown/Movement/No Movement features while charging.
- Accelerometer and movement detection improvements.
- Fixed invalid SMS number when reporting position after call.
|
55.00.18.Rev.02 1.6.11_R.23
|
2021.05.13
|
|
- Fixed issue which occurred during manufactory testing phase with Ver.55.00.18.Rev.01 where device could end with GNSS State = 0
|
55.00.18.Rev.01 1.6.11_R.23
|
2021.05.07
|
- Increased Beacon List from 25 to 100
- Added On Demand Tracking On/Off/Switch button action
- Added On Demand Tracking event indication settings
|
- Increased Configured beacons count from 25 to 100
- If Beacon record sending is configured to be 'Eventual', send only if device sees any beacons
- Improved Power On/Off feature notifications
- Power save mode is working with Data Acquisition time 60s and above
- On Demand Tracking functionality improved with button control and On Demand Tracking event indication
|
55.00.10.Rev.01 1.6.11_R.16
|
2020.11.13
|
- Added Last Known Position feature settings
- Added Power On/Off event settings
- Added Power off with Power key settings
- Added Custom BLE I/O parameters
|
- Added Last Known Position feature on HIGH priority event (alarm, amber alert, man-down, etc).
- When device gains current GPS position after HIGH priority event was generated, device sends another HIGH priority event with updated position and GPS fix timestamp.
- Reworked GNSS status SMS template.
- Fixed issue of data acquisition parameters reset to default values.
|
55.00.07.Rev.09 1.5.15_C.002
|
2020.10.20
|
|
- Important change of charging algorithm. This algorithm provides higher safety and prolonging battery’s life longevity.
- Corrected battery display in percentage
- Improved charging current from PC.
|
55.00.07.Rev.07 1.5.15_C.002
|
2020.09.16
|
|
- Lowered battery charging current from wall charger to 425mA.
- Fixed battery LED indication when battery is fully charged.
|
55.00.07.Rev.02 1.5.15_C.002
|
2020.03.17
|
- Added Man-Down Event On Exit and On Entrance parameters
|
- Updated Server IP and Port saving procedures.
- Reworked Generate Event On Exit and On Entrance logic.
- Reworked handheld devices switching between Charging and Normal modes.
- Reworked User ID values scan after device is turn off/on.
- Reworked Button I/O on-click event.
|
55.00.05.Rev.00 1.5.0_C.007
|
2020.02.13
|
- Removed unnecessary Low Power parameters
- Removed unnecessary Time Synchronization settings
- Implemented On Demand tracking functionality
- Removed unnecessary Number Check Settings panel
- Implemented Event Notification functionality
- Implemented User ID functionality
- Improved BLE beacon functionality
- Implemented Beacon List functionality
- Improved User Interface configuration panel
- Improved Keyboard configuration panel
- Implemented Button IO feature
- Updated default settings
|
- Reworked User Interface configuration.
- Reworked Keyboard configuration.
- Implemented Event Notification panel.
- Implemented Call After Answer functionality
- Implemented User ID functionality.
- Implemented On Demand data acquisition functionality.
- Implemented Button IO Feature.
- Optimized wake up from deep sleep by movement.
- Updated default settings.
- Improved BLE compatibility with beacons.
|
GH5200
Base
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.02.03.Rev.05 1.7.66 B.55.2 R.10
|
2024-01-30
|
- [CHN] Added new AVL ID's SMS events tab
- [FIX] Fixed Online vs Offline configuration discrepancies
- [FIX] Fixed Ultra Deep Sleep naming mismatch
- [FIX] Fixed Tool Tips inaccuracies
- [ADD] Added EYE Sensors support settings and filtering by sensors name and MAC address
- [CHN] Changed device wiki links to teltonika-gps
- [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab
- [FIX] Fixed Roaming operator/Operator Black List .csv file importing
- [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
- [ADD] Added configurable accelerometer sensitivity settings
- [ADD] Added continuous battery charging mode
- [CHN] Changed minimum BLE scan start period value
|
- [CHN] Added possibility to send SMS AVL ID event to few numbers
- [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
- [ADD] Added CSQ level parameter
- [FIX] Fixed Event Notification SMS text maximum length
- [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
- [ADD] Added configurable accelerometer sensitivity options in sleep mode
- [FIX] Fixed ‚btgetlist 3‘ SMS command
- [FIX] Changed battery voltage measurement and charging algorithm
- [ADD] Added EYE Sensor support
- [ADD] BLE sensors Custom field data are displayed in decimal now
- [FIX] Fixed batteries percentage calculation when voltage is Fully charged
- [ADD] Added " dropcall" SMS command to hang up the call.
- [ADD] Added call duration limits for Alarm event
- [ADD] Added Call duration limits for each keyboard button
- [FIX] Fixed call and SMS send issue for Feature>>Event notification
- [FIX] Refactored battery percentage limits checking algorithm
- [FIX] Fixed battery charging status
- [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
- [ADD] Added ability to switch audio to Bluetooth headset/speaker with a button.
- [FIX] Fixing issue when incoming call voice audio doesn't work via HFP
- [FIX] AXL and LIS3DH changes to prevent unwanted wake up from sleep mode and prevent fake movement detection
- [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
- [FIX] Fixed GSM established LED indication turning off issue
- [CHN] Changed minimum BLE scan start period configuration value.
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.02.03.Rev 05 1.7.66_B.55.2_R.10
|
2023-12-13
|
- [CHN] Added new AVL IDs SMS events tab
- [FIX] Fixed Online vs Offline configuration discrepancies
- [FIX] Fixed Ultra Deep Sleep naming mismatch
- [FIX] Fixed Tool Tips inaccuracies
- [ADD] Added EYE sensors support settings and filtering by sensor's'name and MAC address
- [CHN] Changed device wiki links to teltonika-gps
- [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab.
- [FIX] Fixed Roaming operator/Operator Black list .csv file importing
- [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
- [ADD] Added configurable accelerometer sensitivity settings
- [ADD]Added events call duration limits
- [ADD]Added call duration limits for keyboard buttons independently.
- [ADD] Added continuous battery charging mode
- [CHN] Changed minimum BLE scan start period value.
|
- [CHN] Added possibility to send SMS AVL ID event to few numbers
- [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
- [ADD] Added CSQ level parameter
- [FIX] Fixed Event Notification SMS text maximum length
- [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
- [ADD] Added configurable accelerometer sensitivity options in sleep mode
- [FIX] Fixed ‚btgetlist 3‘ SMS command
- [FIX] Changed battery voltage measurement and charging algorithm
- [ADD] Added EYE sensor support
- [ADD] BLE sensors Custom field data are displayed in decimal now
- [FIX] Fixed batteries percentage calculation when voltage is Fully charged
- [ADD] Added " dropcall" SMS command to hang up the call.
- [ADD] Added call duration limits for Alarm event
- [ADD] Added Call duration limits for each keyboard button
- [FIX] Fixed call and SMS send issue for Feature>>Event notification
- [FIX] Refactored battery percentage limits checking algorithm
- [FIX] Fixed battery charging status
- [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
- [ADD] Added ability to switch audio to Bluetooth headset/speaker with a button.
- [FIX] Fixing issue when incoming call voice audio doesn't work via HFP
- [FIX] AXL and LIS3DH changes to prevent unwanted wake up from sleep mode and prevent fake movement detection
- [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
- [FIX] Fixed GSM established LED indication turning off issue
- [CHN] Changed minimum BLE scan start period configuration value.
|
Proximity
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.01.02.Rev.200 1.5.15_C.232
|
2021.11.15
|
- Fixed In Use satellites not display issue
- Add missing parameter IDs in tooltips
|
- Added XT26G01CWSIGT and GD5F1GQ5UE NAND flash support
- The maximum battery charging temperature changed from 50°C to 45°C
- Maximum operating temperature changed from 65°C to 59°C
- Fixed Remote Connection indication.
- SMS commands will return time with applied time zone
- Fixed FW version display in FOTA WEB
- Fixed SMS send and Call issue, when GPRS send period is set to 0 sec.
- Changed minimum charging temperature from -10°C to 1°C
- Fixed configuration saving error. Which was happening due FW version change
- Increased BLE scan stability.
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
55.00.08.Rev.349 1.5.15_C.228
|
2021.05.07
|
- Added configurable Proximity indication pause
- Added option 'Advertise only' for proximity while charging
|
- Added configurable Proximity indication pause.
- Changed default Scan Window and Scan Interval
- Added option 'Advertise only' for proximity while charging
- Corrections for data sending via RUTX
- If Beacon record sending is configured to be 'Eventual', send only if device sees any beacons
|
55.00.08.Rev.344 1.5.15_C.225
|
2021.01.14
|
- Added Proximity Violator type iBeacon
|
- Improved proximity feature stability.
- Reworked device connection with RUTX.
- Improved proximity advertising scanning stability.
- Safe charging improvements for GH5200.
- Added feature which allows to use Beacons with proximity feature.
- Fixed device Power on from USB, when feature is disabled.
- Proximity improvements to support several devices at the same time.
|
55.00.08.Rev.337 1.5.15_C.222
|
2020.10.23
|
- Added Proximity with RUTX setting
- Added Proximity RDDI exit threshold setting
- Added Proximity RDDI moving average samples setting
|
- Improved RSSI level calculation logic, averaging according to configurated sample size was implemented.
- Added BLE advertising interval parameter.
- Added duplicate scan filter to improve BLE performance.
|
55.00.08.Rev.335 1.5.15_C.219
|
2020.10.09
|
- Added Teltonika beaons setting
|
- Improved BLE power level parameters.
- Added Proximity RSSI exit threshold parameter.
- Added Proximity RSSI moving average parameter.
- Reworked generation of Proximity records.
- Changed Proximity record priority from Low to High.
- Reworked Proximity record sending according to Data Acquisition.
|
55.00.08.Rev.334 1.5.15_C.219
|
2020.09.28
|
- Added Teltonika beaons setting
|
- Added new beacon detection option Teltonika (device only detects Teltonika devices).
- Improved Proximity detection, works with Beacon Detection All and Beacon Detection Teltonika settings.
- Improved Proximity contact duration calculation.
- Improved Beacon detection stability.
|
55.00.08.Rev.332 1.5.15_C.217
|
2020.09.28
|
- Added Home Zone on Exit on entrance settings
|
- Improved Proximity record sending.
- Reworked Home Zone on exit and on entrance event generation.
- Improved Power Off event delay.
- Corrected Power On/Off event logic.
- Reworked Proximity SMS, IMEI is sent instead of BLE MAC
- Proximity Service ID was removed.
|
TAT100
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.569
BlueNRG version: 10.0.3.Rev.00 for TAT100 HW ver.: 31
1.0.3.Rev.00 for TAT100 HW ver.: 62
Configurator version: 1.7.74_E.TAT1_R.7
|
2024.08.19
|
- Added an option to configure TLS functionality.
- Added an option to configure SMS record sending.
- Added an option to configure MQTT Azure and AWS support.
- Added an option to configure I am alive feature.
|
- Added TLS functionality feature.
- Added SMS record sending feature.
- Added MQTT Azure and AWS support.
- Added I am alive feature.
- Fixed X, Y and Z IO elements not being included with First Power On record.
- Extended On Stop and On Move periodic timers to maximum value of 7 days.
- Improvements to Static Navigation logic in no GPS situation.
- New AVL ID 69 value added (4 - no GPS in Static Navigation).
- Improved Recovery mode trigger logic in Lost Sensor scenario.
- Added error code when BLE sensor is lost.
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.564
BlueNRG version: 10.4.12 for TAT100 HW ver.: 31
0.4.12 for TAT100 HW ver.: 62
Configurator version: 1.7.74_B.TAT1_R.6
|
2024.03.12
|
- Fixed configurator crash after firmware update.
- Added cell ID I/O elements
- Fixed error when disabling BLE features in configuration.
- Added GSM area code I/O element
- Simplified EYE sensor configuration.
- Added Autonomous Alarm System feature.
|
- Fixed periodic timer starting in Recovery mode.
- Improved backup tracker scan procedure.
- Fixed issue with GPS fix with First Power On record.
- Improved energy management in sleep mode when device is in motion.
- Fixed crash on BLE sensor alarm.
- Bluetooth scanning and data parsing optimization.
- DNS resolve improvements.
- Fixed periodic timer starting when tracking scenario selected as None.
- Changed default movement sensitivity to 150 mG
- Changed default GNSS mode to GLONASS, GPS and GALILEO
- Fixed EYE sensor data multiplier for correct data displaying.
- Fixed issue if GPRS is lost during record sending.
- Fixed GPRS command processing in UDP mode.
- Improved received SMS reading process.
- Improved connection to Fota process.
- Fixed BLE sensor data not being included in periodic records.
- Improved static navigation logic.
- Improved Bluetooth scan stability.
- Added BLE beacons for Recovery mode trigger.
- Movement logic rework.
- Added condition to stop GNSS search if less than 3 satellites found in the first 60 seconds.
|
Firmware version: 55.00.16.Rev.545
BlueNRG version: 10.3.12 for TAT100 HW ver.: 31
0.3.12 for TAT100 HW ver.: 62
Configurator version: 1.7.16_E.TAT100.R23 RELEASE
|
2022.08.23
|
|
- Fixed issue with incorrectly detected SIM slot for eSIM devices.
|
Firmware version: 55.00.16.Rev.543 BlueNRG version: 10.3.12 for TAT100 HW ver.: 31 0.3.12 for TAT100 HW ver.: 62 Configurator version: 1.7.16_E.TAT100.R23 RELEASE
|
2022.08.08
|
- Updated Teltonika Configurator version to set Central device default IMEI to 300000000000000
- Added Recovery mode option
- Added I/O element of Recovery Mode
- Added more options of movement sensitivity threshold [50-1000mG]
- Configurator for BLE FW and Backup FW was merged into one.
|
- SMS command created for getting device statistics
- Protection from writing other devices FW
- Added condition to prevent modem waking up at midnight if scheduler is configured
- Added reconfiguration mechanism that lets FW work with / without SMPS filterMissing
- Fixed issue of missing 4th sensor's data with Monitoring operand
- Fixed too frequent / unnecessary scans with all sensors configured as monitoring
- Fixed sensors scan starting with monitoring operand when Backup tracker is configured
- Backup tracker scan not starting right after
- Time synchronization every 24 hours
- Fixed LBS data sending issue
- New AVL ID 20015 for Modem UpTime (in seconds)
- Added response sending if recovery command is sent through GPRS
- The next periodic record after Recovery mode deactivation being sent with AVL ID 20012 - fixed
- Reduced EQ Core update frequency
- Fixed battery consumption issue when GSM is jammed.
- LED status changed from constant on to blinking mode to save the battery
- Added Recovery mode feature
- Implemented Recovery mode activation from the Backup tracking alarm
- Added EYE sensors support
- Fixed Minor bugs regarding the sensors
- Fixed Short period Recovery Mode records
- Extended Backup Tracker: Central device IMEI range
- Backup tracker: Scanning logic has been changed, scan duration is not configurable anymore, it is up to 60 seconds by default now.
- Implemented Record timestamp shift feature
- Fixed BLE sensor records with wrong event ID being sent
- Fixed BLE sensor record duplicates with
On change operand
- Fixed BLE sensor
On Exit record not generating when switching to sleep mode
- Fixed
Custom1 sensor data in SMS being sent as NaN (empty)
- Fixed duplicate BLE sensor data after waking up
- Changed required packets amount in backup tracker scenario and minimal scan duration
- Fixed backup tracker alarm not triggering just before wakeup
- Fixed backup tracker not detecting enough packets during BLE scan
- Periodic records do not affect backup tracker alarm record generation
|
Firmware version: 55.00.16.Rev.522 BlueNRG version: 10.2.21.Rev.01 Configurator version: 1.7.16_R.TAT100.R2
|
2021.12.21
|
|
- Improved battery safety features
- Fixed stuck download during FOTA update
- Fixed device not restarting to update FW after FOTA download
- Improved main device packet filtering
- Improved battery voltage measurement
- Fixed the device not restarting after FOTA WEB update when it happens at the same time as periodic record
- Fixed random statistic losses
- Fixed GNSS module status not being accurate in Teltonika Configurator
- Improved static navigation mode
- Fixed scheduler time resync timer not working properly
- Fixed statistic not being deleted from RAM
|
Firmware version: 55.00.15.Rev.519 BlueNRG version: 10.2.14 Configurator version: 1.7.16_R.TAT100.R2
|
2021.10.19
|
|
- Fixed fake movement detection on startup
- Fixed problem when the device is stuck in On Stop tracking mode after reconfiguration
- Added Power-On reason data and fixed version changes to device statistics
- Fixed Backup tracker issue where the alarm mode is not immediately activated when the central device disappears
- Fixed empty GSM I/O elements
- Fixed an issue where UTC is added after each reconfiguration
- Added record printing to
Dump log
- LBS data is not included in records if GNSS fix was caught
- Fixed NTP timesync failure if offset is zero
- Improved record creation (wake up from sleep) during Backup tracker alarms
- Improved GNSS module control with
Static Navigation and LBS
- Added prevention from inappropriate record generation if the battery is low (HW watchdog)
- Added statistic element for USB connected uptime
- Added timestamp to BlueNRG serial prints
- Minor improvement for BlueNRG firmware update via configurator
- Added filter for
LBS cell_id duplicates
- Improved Bluetooth sensor record creation with
'On Change' operand
- Added Bluetooth sensor support
- Added condition to skip LBS data update if location source is only GNSS
- Increased retries of AT+# command in order to avoid empty LBS data from modem
- Changed
Open link timeout to 15s
- Fixed an issue where the tracking mode would change from the scheduler to periodic
- Improved logic for multiple
FOTA Web tasks update in the same connection
- Implemented rule for additional connection to
FOTA Web after baseband firmware update
- Added accelerometer version information inside '.info' serial command
- Fixed an issue with battery voltage
I/O element when record saving is overlapping with a firmware update
- Fixed
Scheduler record sending at midnight
- Fixed missed LBS values inside
I/O elements
- Fixed an issue when GNSS speed is not zero while the device is in a stationary position
- General minor improvements
|
55.00.10.Rev.509 BlueNRG: 10.2.3_Rev.00 1.7.16_E.TAT100_04
|
2021.05.10
|
- Added
Test Connection button
- Temporarily removed
Secondary Server Settings
- Tracking Period default value changed to 28800 (s)
|
- Implemented
Test Connection feature.
- Added BlueNRG logging to DUMP files
- Added LBS data logging to DUMP files
- Added protection that blocks FMB firmware flash to AT devices
- Added time-sync update with asset purpose command
- Improved periodic record timer logic
- Improved battery voltage measurement
- Improved periodic GPRS data sending while USB is connected to the device
- Disabled SMPS filter
- Fixed record sending when movement is triggered at all times
- Improved NTP time-sync
|
55.00.05.Rev.510 BlueNRG: 0.1.7
|
2020.12.03
|
- Removed tracking scenarios
- Removed speed source parameter
- Removed record saving/sending without TS parameter
- Removed LED Indication parameter
- Removed NTP resync parameter
|
- Implemented FOTA support.
- Improved GNSS position capturing.
- Reworked Periodic and Scheduler tracking counters.
- Implemented device logging via USB.
- Implemented statistics acquisition to flash memory.
|
55.00.05.Rev.507 BlueNRG: 0.1.5
|
2020.09.29
|
- Implemented GNSS Source configuration. Available options: BeiDou, GLONASS, Galileo and GPS.
- Added I/O elements: Data Mode, GSM Signal, GNSS Status, GNSS PDOP, GNSS HDOP, Speed, GSM Cell ID, GSM Area Code, Battery Voltage, Active GSM Operator, ICCID, Coordinates ISO6709.
- Added SMS command autorization via Login and Password logic.
|
- Implemented 'Codec 8', 'Codec 8 Extended' and 'Codec 12' protocols.
- Implemented NTP, NITZ and GNSS time synchronization sources.
- Implemented ability to send GPRS data from device via TCP or UDP channels.
- Implemented connection to server timeouts.
- Ported TLS encryption functionality from other Teltonika devices.
- Implemented Periodic and Scheduler tracking.
- Implemented BlueNRG firmware update via GPRS. This function will be used to reflash BlueNRG firmware via FOTA WEB.
- Added GSM number authorization logic.
|
TAT140
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.569
BlueNRG version: 1.0.3.Rev.00
Configurator version: 1.7.74_E.TAT1_R.7
|
2024.08.19
|
- Added an option to configure TLS functionality.
- Added an option to configure SMS record sending.
- Added an option to configure MQTT Azure and AWS support.
- Added an option to configure I am alive feature.
|
- Added TLS functionality feature.
- Added SMS record sending feature.
- Added MQTT Azure and AWS support.
- Added I am alive feature.
- Fixed X, Y and Z IO elements not being included with First Power On record.
- Extended On Stop and On Move periodic timers to maximum value of 7 days.
- Improvements to Static Navigation logic in no GPS situation.
- New AVL ID 69 value added (4 - no GPS in Static Navigation).
- Improved Recovery mode trigger logic in Lost Sensor scenario.
- Added error code when BLE sensor is lost.
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.564 BlueNRG version: 0.4.12 Configurator version: 1.7.74_B.TAT1_R.6
|
2024.03.12
|
- Fixed configurator crash after firmware update.
- Added cell ID I/O elements
|
- Fixed periodic timer starting in Recovery mode.
- Improved backup tracker scan procedure.
- Fixed issue with GPS fix with First Power On record.
- Improved energy management in sleep mode when device is in motion.
- Fixed crash on BLE sensor alarm.
- Bluetooth scanning and data parsing optimization.
- DNS resolve improvements.
- Fixed periodic timer starting when tracking scenario selected as None.
- Added cell ID I/O elements
|
Firmware version: 55.00.16.Rev.558 BlueNRG version: 0.4.8 Configurator version: 1.7.16_B.TAT1_R.3
|
2023.07.18
|
* Removed non configurable elements
|
- [FIX] Improved EYE sensor data detection to be suitable for all sensor modes
- [FIX] Fixed Periodic timer still running when Recovery mode is activated in sleep from Backup tracker
- [FIX] Hotfix for EG915ULA modem status commands
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.557 BlueNRG version: 0.4.7 Configurator version: 1.7.16_B.TAT1_R.1
|
2023.05.10
|
Initial release
|
Initial release
|
TAT141
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.569
BlueNRG version: 1.0.3.Rev.00
Configurator version: 1.7.74_E.TAT1_R.7
|
2024.08.19
|
- Added an option to configure TLS functionality.
- Added an option to configure SMS record sending.
- Added an option to configure MQTT Azure and AWS support.
- Added an option to configure I am alive feature.
|
- Added TLS functionality feature.
- Added SMS record sending feature.
- Added MQTT Azure and AWS support.
- Added I am alive feature.
- Fixed X, Y and Z IO elements not being included with First Power On record.
- Extended On Stop and On Move periodic timers to maximum value of 7 days.
- Improvements to Static Navigation logic in no GPS situation.
- New AVL ID 69 value added (4 - no GPS in Static Navigation).
- Improved Recovery mode trigger logic in Lost Sensor scenario.
- Added error code when BLE sensor is lost.
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.564 BlueNRG version: 0.4.12 Configurator version: 1.7.74_B.TAT1_R.6
|
2024.03.12
|
- Fixed configurator crash after firmware update.
- Added cell ID I/O elements
|
- Fixed periodic timer starting in Recovery mode.
- Improved backup tracker scan procedure.
- Fixed issue with GPS fix with First Power On record.
- Improved energy management in sleep mode when device is in motion.
- Fixed crash on BLE sensor alarm.
- Bluetooth scanning and data parsing optimization.
- DNS resolve improvements.
- Fixed periodic timer starting when tracking scenario selected as None.
- Added cell ID I/O elements
|
Firmware version: 55.00.16.Rev.558 BlueNRG version: 0.4.8 Configurator version: 1.7.16_B.TAT1_R.3
|
2023.07.18
|
* Removed non configurable elements
|
- [FIX] Improved EYE sensor data detection to be suitable for all sensor modes
- [FIX] Fixed Periodic timer still running when Recovery mode is activated in sleep from Backup tracker
- [FIX] Hotfix for EG915ULA modem status commands
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.557 BlueNRG version: 0.4.7 Configurator version: 1.7.16_B.TAT1_R.1
|
2023.05.10
|
Initial release
|
Initial release
|
TAT240
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.569
BlueNRG version: 1.0.3.Rev.00
Configurator version: 1.7.74_E.TAT1_R.7
|
2024.08.19
|
- Added an option to configure TLS functionality.
- Added an option to configure SMS record sending.
- Added an option to configure MQTT Azure and AWS support.
- Added an option to configure I am alive feature.
- Added an option to configure SMS alert on Tamper event.
|
- Added SMS alert on Tamper event feature.
- Fixed X, Y and Z IO elements not being included with First Power On record.
- Extended On Stop and On Move periodic timers to maximum value of 7 days.
- Improvements to Static Navigation logic in no GPS situation.
- New AVL ID 69 value added (4 - no GPS in Static Navigation).
- Improved Recovery mode trigger logic in Lost Sensor scenario.
- Added error code when BLE sensor is lost.
|
VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
Firmware version: 55.00.16.Rev.564 BlueNRG version: 0.4.12 Configurator version: 1.7.74_B.TAT1_R.6
|
2024.03.12
|
|
- Fixed periodic timer starting in Recovery mode.
- Improved backup tracker scan procedure.
|
Firmware version: 55.00.16.Rev.562 BlueNRG version: 0.4.11 Configurator version: 1.7.74_B.TAT1_R.6
|
2023.12.20
|
|
|