Stable Firmware & Software CHANGELOG

From Teltonika Telematics Wiki
(Redirected from TAT240 Firmware errata)
Main Page > Autonomous Trackers > TAT240 > TAT240 Firmware errata


Select the needed category:

Basic Trackers Fast & Easy Trackers Advanced Trackers Autonomous Trackers Sensors
OBD Trackers CAN Trackers & Adapters Professional Trackers E-Mobility Trackers Video Solutions


E-Mobility Trackers

TFT100

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.02.03.Rev.06
1.7.66_B.55.2_R.11 		2024-01-15
  • [ADD] Added CAN Debug feature and CAN Log parameter
  • [CHN] Increased DOUT duration limit for Overspeeding, Green Driving, Idling features
  • [ADD] Added Odometer parameter for UART, RS232 and RS485
  • [REM] Removed CAN and RS485 termination resistor management parameter
  • [FIX] Fixed Askoll CAN protocol charge voltage and current I/O parameters visibility, removed malfunction indication I/O
  • [FIX] Fixed FLEX CAN protocol parameters duplication
  • [ADD] Added Ignition ON Counter feature
  • [ADD] Added Separate Manual CAN I/O Reset feature and related parameters
  • [CHN] Reduced max sensor size to 64 bytes
  • [CHN] Moved Manual CAN baudrate parameter to main CAN I/O section
  • [CHN] Changed Manual CAN Settings table and simplified CAN protocol settings
  • [CHN] Changed device Wiki links to Teltonika-gps
  • [FIX] Fixed BLE Custom I/O Low level maximum value to match valid range by firmware
  • [REM] Removed wrong parameter (ID: 740 and 741) tool tips
  • [ADD] Added Eye Sensors support
  • [FIX] Fixed Roaming/Blacklist CSV file import
  • [FIX] Fixed Manual CAN request period max range
  • [REM] Removed Manual CAN and Manual J1939 parameters option to leave empty field
  • [ADD] Added High resolution vehicle distance and Trip Distance CAN ID and I/O to Default J1939 protocol
  • [ADD] Added new Askoll CAN protocol I/O's
  • [CHN] Changed Manual CAN Commands interface to table
  • [REM] Removed ISO6709 I/O
  • [FIX] Fixed Tool Tips inaccuracies
  • [FIX] Fixed Online vs Offline configuration discrepancies
  • [CHN] Changed Manual CAN I/O and Ignition range Low and High level maximum value range
  • [FIX] Fixed J1939 Source Address maximum address to 253
  • [FIX] Fixed UART Battery temperature Low level maximum value range
  • [FIX] Fixed Ultra Deep Sleep naming mismatch
  • [ADD] Added SMS Events functionality
  • [FIX] Fixed auto answer (HF) wrong parameter values
  • [REM] Removed RS485 Mode selection duplication
  • [CHN] Increased DOUT duration limit for Overspeeding, Green Driving, Idling features
  • [ADD] Added CAN Debug feature
  • [CHN] Changed 0% battery level voltage to 3.3V
  • [ADD] Added battery percentage level to battery info SMS
  • [ADD] Added Ignition ON Counter feature
  • [ADD] Added protection against network stuck reset when device is working from battery and immobilizer scenario might be activated
  • [CHN] Improved CAN data reading operation for each available CAN protocol
  • [ADD] Added CAN chip sleep when external power is not available or device is in Ultra Deep Sleep
  • [ADD] Added Separate Manual CAN I/O Reset feature
  • [ADD] Added new Askoll CAN I/O's
  • [ADD] Added watchdog timer for CAN task
  • [CHN] Improved DOUT control during device's boot-up
  • [FIX] Fixed incorrect CAN SMS/GPRS AVL response
  • [ADD] Added High resolution vehicle distance and Trip Distance CAN ID and I/O to Default J1939 protocol
  • [REM] Removed ISO6709 I/O
  • [FIX] Fixed ignition detection with power voltage higher than 65V
  • [FIX] Fixed CAN and UART I/O low level range values
  • [ADD] Added SMS Events functionality
  • [FIX] Fixed AVL ID 239 (Ignition) value not updating in records
  • [FIX] Fixed Auto Geofence text field parameter resetting after device reboot
  • [ADD] Added Eye Sensors support
  • [CHN] Changed CAN None protocol operation - CAN is not configured, CAN task suspended
  • [CHN] Reduced 1-Wire startup delay after wake up from UDS
  • [ADD] Added DIN2 status to getio command
  • [FIX] Fixed setdigout speed command when GNSS fix is not available


VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.01.10.Rev.00
1.6.11 R.39 		2022.09.09
  • [CHN]: Changed Default and Minimum CAN Command period. Changed tooltips.
  • [ADD]: Add timestamp backup description
  • [CHN]: Corrected misleading and outdated tooltips
  • [CHN]: Changed TFT100 default configuration.
  • [ADD]: Added CAN I/O reset parameter.
  • [ADD]: Govecs FLEX (TFT100) changes were merged into 7.0.33 version.
  • [ADD]: Added AES128 BLE encryption KEY parameter
  • [CHN]: Updated tooltip description for DOUT Deactivation Via DIN
  • [FIX]: Fixed BLE Sensor Custom IO SMS sending with value NaN and displaying as ASCII in Configurator.
  • [FIX]: Fixed device constantly opening and closing GPRS with permanent link if APN is empty in configurator.
  • [FIX]: Fixed permanent link not changing protocol after reconfiguration.
  • [CHN]: Updated FOTA WEB protocol ID 0x04 => 0x05
  • [FIX]: Increased connection interval in order to speed up connection through BLE terminal.
  • [FIX]: Fixed POSI command skipping.
  • [FIX]: Fixing network stability issues.
  • [FIX]: Fixed timestamp not renewing for Eddystone beacons.
  • [FIX]: Added condition to prevent closing socket, if GPRS command is received and response was not sent yet.
  • [FIX]: Fixed issue, when after pin reconfiguration from DOUT to DIN, DOUT stays ON.
  • [FIX]: Fixed periodic CAN command message disabling.
  • [FIX]: Fixed Flex CAN protocol reading 0 values after power is cut off.
  • [FIX]: Fixed Manual CAN commands periodical sending.
  • [CHN]: Changed TFT100 default configuration.
  • [CHN]: Increased external queue size to prevent abnormal restarts during BLE scan.
  • [ADD]: Added Reset CAN IO values parameter.
  • [FIX]: Fixed CAN message sending irregularities.
  • [FIX]: Fixed J1939 CAN reading recovery after external power is off.
  • [ADD]: Added priority for charger control factory command.
  • [FIX]: Fixed a broken GSM connection due to incorrect SIM card selection.
  • [FIX]: Fixed FOTA WEB fail when the files requested for download do not exist.
  • [FIX]: Fixed lost BLE AES encryption key after reboot.
  • [ADD]: Merged Govecs FLEX changes into base. New configuration 7.0.33 created also.
  • [FIX]: Fixed DOUT delay after ignition detection.
  • [FIX]: Fixed Manual CAN Ignition and Speed I/O‘s timeout issue
  • [FIX]: Fixed Manual CAN Speed Source I/O‘s Speed Offset min/max values
  • [ADD]: Added AES128 BLE encryption functionality
  • [FIX]: Fixed Manual CAN I/O triggers with configured operands
  • [FIX]: Fixed GPRS commands sending with TLS encryption
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.01.02.Rev.02
1.6.11_R.30 		2021.11.03
  • Parameters for Ignition, Speed extraction from manual CAN messages added.
  • Added immobilizer functionality which is not dependent on ignition.
  • GNSS source parameter mask changed to allow only valid GNSS modes.
  • FLEX protcol functionality added.
  • Manual CAN Commands functionality moved to separate tab.
  • 120 Ohm resistor settings added for CAN, RS485 variants.
  • Last know position parameter added.
  • PDOP filter parameters added.
  • Fixed FW up/downgrade for TFT CAN devices with new Flash component.
  • SMS commands updated. Commands will return time with time zone applied.
  • Fixed minus temperature calculation.
  • PDOP filter added.
  • Movement detection tracking fixed.
  • GNSS source parameter only available value can be set.
  • Added Backup tracker scenario.
  • Added speed, ignition source manual CAN functionality.
  • Added immobilizer functionality which is not dependent on ignition.
  • Updated Manual CAN IO value dispaly. The value is cleared after configuration changed.
  • Added FLEX protocol support.
  • Added a time guard if BLE scan job is stuck.
  • Fixed external voltage value representation in battery SMS command response.
  • Added 120 Ohm resistor support.
  • Added Last known position parameter added.
55.00.14.Rev.00
1.6.11_R.19 		2021.02.03
  • Parameter order in IO section was updated.
  • Timestamp backup functionality added.
  • Added possibility to include additional IOs to eventual crash record.
  • Added Endianess, Payload and RTR options to Manual CAN settings.
  • Added possibility to include additional IOs to eventual crash record
  • Fixed DOUT state after immobilizer.
  • Fixed double iButton scanning issue for immobilizer after sleep.
  • Fixed Crash event value.
  • Added battery percentage value to the SMS
  • Increased compatible beacons count from 25 to 100.
  • Fixed memory leak, when the GPS module is turned on and off frequently.
  • Timestamp backup functionality added.
  • Improved Manual CAN data reading.
  • Beacon detection regarding the timestamp for immobilizer functionality, minimal ignition tmo changed to 5s.
  • Added Request DA parameter to Manual J1939 (availability to send request to specific adress).
  • Added Payload and RTR parameters to Manual CAN (availability to send requests with data).
  • Option to start Manual CAN commands on startup was added.
  • Added command .can_dbg:<1/0>, which turn on/off the additional CAN debug functionality.
55.00.09.Rev.08
1.6.11_R.14 		2020.10.16
  • Added BMS2 I/O parameters to Bosch CAN protocol;
  • Added DOUT control via Ignition feature;
  • Added Manual J1939 protocol;
  • Added permanent link with server feature;
  • Added Manual CAN commands functionality;
  • Added Falldown functionality with autocalibration;
  • Added Battery level I/O parameter;
  • Added Battery Charge Mode feature;
  • Added Beacon selection with Immobilizer feature;
  • Added functionality to hide DOUT selection near all features if DIN is selected;
  • Added Manual CAN feature;
  • Added Default J1939 protocol support with it's I/O parameters.
55.00.08.Rev.03
1.5.15_C.003 		2020.04.10
  • Optimized Digital Output tool tips;
  • Optimized UART panel title to be more accurate;
  • Removed duplicated I/O parameters;
  • Added RS485 Super Soco protocol;
  • Added wake up via DIN1 in Ultra Deep Sleep mode functionality;
  • Added GoUrban RS485 protocol for Super Soco e-scooter;
  • Added new TFT100 hardware support;
55.00.06.Rev.01
1.5.0_C.007 		2020.02.07
  • Implemented an option to select Analog Input Value Range;
  • Optimized default configuration;
  • Added DOUT Control Via Call feature;
  • Added iButton Read Notification and Immobilizer feature;
  • Added On Demand Tracking feature;
  • Added new Ignition Source parameters - Accelerometer, DIN1, Power Voltage, CAN;
  • Implemented DIN/DOUT selection ability;
  • Added Bosch CAN Powertrain and Askoll protocol selection and I/O's;
  • Added TFT100 hardware support;
  • Optimized Askoll specific commands;
  • Optimized CAN chip and NAND SPI Chip select synchronization;
55.00.05.Rev.00
1.6.11_R.X 		2020.01.17
  • Optimized iButton Read Notification feature;
  • Added DOUT Control Via Call and iButton features;
  • Added Immobilizer scenario;
  • Added DOUT Control via Call scenario;
  • Added new Ignition Source parameters - Accelerometer, DIN1, Power Voltage, CAN;
  • Implemented the ability to configure DIN/DOUT;
  • Added FOTA WEB support;
  • Added Askoll related SMS commands - askoll_unlock, askoll_horn, askoll_tc;
  • Optimized data reading through CAN interface;
  • Implemented Bosch CAN Powertrain and Askoll protocols;
  • Added DOUT protection;
  • Added base functionality for all modifications;
  • Added TFT100 hardware support;

TST100

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.01.10.Rev.00
1.6.11 R.39 		2022.09.12
  • [ADD]: Added timestamp backup description.
  • [CHN]: Corrected misleading and outdated tooltips.
  • [ADD]: Added Hergele scooter protocol.
  • [ADD]: Added SIM card tamper protection feature.
  • [FIX]: Fixed BLE Sensor Custom IO SMS sending with value NaN and displaying as ASCII in Configurator.
  • [FIX]: Fixed device constantly opening and closing GPRS with permanent link if APN is empty in configurator.
  • [FIX]: Fixed permanent link not changing protocol after reconfiguration.
  • [CHN]: Updated FOTA WEB protocol ID 0x04 => 0x05
  • [FIX]: Increased connection interval in order to speed up connection through BLE terminal.
  • [FIX]: Fixed POSI command skipping.
  • [FIX]: Fixing network stability issues.
  • [FIX]: Fixed timestamp not renewing for Eddystone beacons.
  • [FIX]: Added condition to prevent closing socket, if GPRS command is received and response was not sent yet.
  • [ADD]: Added SIM card tamper protection feature.
  • [ADD]: Added BT whitelist for Solebe lock.
  • [ADD]: Hergele scooter support added.
  • [CHN]: Increased external queue size to prevent abnormal restarts during BLE scan.
  • [FIX]: Fixed a broken GSM connection due to incorrect SIM card selection.
  • [ADD]: HeadLight status in Scooter IO added
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.01.02.Rev.01
1.6.11_R.30 		2021.11.03
  • Changed SMS Timezone label.
  • GNSS source parameter mask changed to allow only valid GNSS modes.
  • Changed scooter speed limits IOs high/low ranges and default values.
  • Added Segway Cable Lock I/O elements.
  • Changed unauthorized movement buzzer control default values.
  • SMS commands updated. Commands will return time with time zone applied.
  • Added Segway wired lock support.
  • Movement detection tracking fixed.
  • For GNSS source parameter only available values can be set.
  • Fixed Unauthorized Movement event SMS sending.
  • Fixed record generation with correct AVL ID for Unauthorized Movement.
55.00.22.Rev.00
1.6.11_R.27 		2021.08.23
  • Changed GNSS source parameter mask to allow only valid GNSS modes.
  • Changed scooter speed limits IOs high/low ranges and default values.
  • Changed Data Acquisition tool tips and labels.
  • Added Falldown auto calibration parameter.
  • Added Unauthorized movement functionality.
  • Added Last known position parameter.
  • Fixed GPS automatic always ON at the start.
  • Updated function to wake up the device if it is moved during "Data sending state".
  • Fixed I/O Sleep mode element to send an event messages on entering the mode.
  • Added Last known position parameter.
  • Added pulsedigout command with on/off timeouts in ms and repeats.
  • Fixed GNSS Fix status always on after changing GNSS source.
  • Updated restricted I/Os by scooter model and fixed battery lock status value.
  • Added Unauthorized movement functionality.
  • Added Falldown auto calibration support for TST100.
  • Changed Battery value SMS text format changed to unsigned int.
  • Added Segway MAX autodetection and MC FW update.
  • Added Segway ES autodetection and MC FW update.
  • Fixed periodic data record generation in order to avoid skipping.
  • Updated Segway ES2/4 FW (ESC 4.0.5).
  • Added a time guard if BLE scan job is stuck.
  • Fixed Unauthorized Movement event SMS sending.
  • Fixed record generation with correct AVL ID for Unauthorized Movement.
  • Fixed ext voltage value representation in battery SMS command response.
  • Fixed scooter speed limits IOs hi/lo ranges check.
  • Fixed unauthorized movement buzzer control using default values.
55.00.14.Rev.00
1.6.11_R.19 		2021.02.03
  • Added Baudrate options.
  • Added Battery lock status Scooter IO element.
  • Added battery percentage value to the SMS.
  • Increased compatible beacons count from 25 to 100.
  • Fixed memory leak, when the GPS module is turned on and off frequently.
  • Changed scooters' IOs filtering depending on protocol.
  • Fixed locking behavior during ride.
  • Improved Movement detection.
  • Segway MAX MC FW was updated to 21.1.0.
  • Added Baudrate options.
  • Fixed temperature and FW version reading in FitRider e-kick scooters.
  • Fixed speed limit function. Added command scsetspdlimt2s for FitRider T2s e-kick scooters.
  • Added debug option for sending/receiving FitRider data packets.
  • Segway MAX scooters locking sequence changed: when scooter is moving and command to lock the scooter was received, the engine is turned off and after the scooter is fully stopped it is locked.
  • Added Battery Lock control command and Battery lock status IO element.
55.00.09.Rev.08
1.6.11_R.14 		2020.10.16
  • Updated scooter's FW rendering in E-Scooter I/O panel from DEC to HEX;
  • Added permanent link with server feature;
  • Removed accelerometer's autocalibration parameter;
  • Added 3 new I/O parameters - Normal/Eco/Sport speed limit;
  • Added BT Status I/O parameter;
  • Improved BLE lock functionality;
  • Added 3 new I/O parameters - Normal/Eco/Sport speed limit;
  • Updated Segway MAX kick e-scooter's MC FW version checking functionality;
  • Updated scgetbtcode and sclookfor commands;
  • Added BT Status I/O parameter;
  • Updated Segway MAX MC and BMS FW versions to 21.0.7 and 3.5.6 correspondingly;
  • Removed Segway scooter's model detection based on serial number. Make sure to always select the correct scooter's protocol!
  • Added SMS/GPRS command for packet's logging - scdbg <arg>; <arg> = 1 - enable, 0 - disable;
  • Updated scbuzzerctrl command functionality with Xiaomi kick e-scooter;
  • Updated battery overheat detection.
55.00.09.Rev.1
1.6.11_R.8 		2020.06.16
  • Added permanent link with the server feature
  • Implemented Solebe Y905 Bluetooth lock feature with required parameters (Lock status, Lock battery)
  • Minor changes
  • Implemented permanent link with server functionality;
  • Added Solebe Y905 Bluetooth lock support;
  • Minor changes;

Autonomous Trackers

TMT250

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.02.03.Rev.05
1.7.66 B.55.2 R.10 		2024-01-30
  • [CHN] Added new AVL ID's SMS events tab
  • [FIX] Fixed Online vs Offline configuration discrepancies
  • [FIX] Fixed Ultra Deep Sleep naming mismatch
  • [FIX] Fixed Tool Tips inaccuracies
  • [ADD] Added EYE Sensors support settings and filtering by sensors name and MAC address
  • [CHN] Changed device wiki links to teltonika-gps
  • [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab
  • [FIX] Fixed Roaming operator/Operator Black List .csv file importing
  • [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
  • [ADD] Added configurable accelerometer sensitivity settings
  • [ADD] Added continuous battery charging mode
  • [CHN] Changed minimum BLE scan start period value
  • [CHN] Added possibility to send SMS AVL ID event to few numbers
  • [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
  • [ADD] Added CSQ level parameter
  • [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
  • [FIX] Added configurable accelerometer sensitivity options in sleep mode
  • [FIX] Fixed ‚btgetlist 3‘ SMS command
  • [FIX] Changed battery voltage measurement and charging algorithm
  • [ADD] Added EYE Sensor support
  • [ADD] BLE Sensors Custom field data are displayed in decimal now
  • [FIX] Fixed batteries percentage calculation when voltage is Fully charged
  • [FIX] Refactored battery percentage limits checking algorithm
  • [FIX] Fixed battery charging status
  • [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
  • [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
  • [FIX] Fixed GSM established LED indication turning off issue
  • [CHN] Changed minimum BLE scan start period configuration value.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.02.03.Rev 05
1.7.66_B.55.2_R.10 		2023-12-13
  • [CHN] Added new AVL IDs SMS events tab
  • [FIX] Fixed Online vs Offline configuration discrepancies
  • [FIX] Fixed Ultra Deep Sleep naming mismatch
  • [FIX] Fixed Tool Tips inaccuracies
  • [ADD] Added EYE sensors support settings and filtering by sensor's'name and MAC address
  • [CHN] Changed device wiki links to teltonika-gps
  • [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab.
  • [FIX] Fixed Roaming operator/Operator Black list .csv file importing
  • [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
  • [ADD] Added configurable accelerometer sensitivity settings
  • [ADD] Added continuous battery charging mode
  • [CHN] Changed minimum BLE scan start period value.
  • [CHN] Added possibility to send SMS AVL ID event to few numbers
  • [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
  • [ADD] Added CSQ level parameter
  • [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
  • [ADD] Added configurable accelerometer sensitivity options in sleep mode
  • [FIX] Fixed ‚btgetlist 3‘ SMS command
  • [FIX] Changed battery voltage measurement and charging algorithm
  • [ADD] Added EYE sensor support
  • [ADD] BLE sensors Custom field data are displayed in decimal now
  • [FIX] Fixed batteries percentage calculation when voltage is Fully charged
  • [FIX] Refactored battery percentage limits checking algorithm
  • [FIX] Fixed battery charging status
  • [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
  • [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
  • [FIX] Fixed GSM established LED indication turning off issue
  • [CHN] Changed minimum BLE scan start period configuration value.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.01.02.Rev.01
1.6.11_R.30 		2021.10.25
  • Change No Movement/Movement event SMS text
  • Added Race Mode feature
  • Added Race Mode for GNSS data live tracking
  • Fixed LED indication stuck when Man-Down Cancel button is pressed
  • Fixed FW version display in FOTA WEB
  • Fixed possibility to configure forbidden GNSS source via SMS or GPRS
  • Fixed fake movement events when Low power mode is used
  • Fixed BLE scan stuck when Xiaomi bracelet is used
  • Fixed restarts when Beacon on Demand feature is used for longer time
  • Fixed Alarm call delay issue
  • Fixed FW update issue with XT26G01CWSIGT flash
  • Added XT26G01CWSIGT and GD5F1GQ5UE NAND flash support
  • Changed minimum charging temperature from -10°C to 1°C
  • SMS commands will return time with applied time zone
  • The maximum battery charging temperature changed from 50°C to 45°C
  • Maximum operating temperature changed from 65°C to 59°C
55.00.21.Rev.00
1.6.11_R.26 		2021.08.10
  • 'Data Acquisition' tool tips and labels changed.
  • Changed BLE 'Update frequency' name and tool tips.
  • Fixed 'Beacon on demand' labels.
  • Added possibility to Enable or Disable Mandown/Movement/No Movement features while charging.
  • Accelerometer and movement detection improvements.
  • Fixed invalid SMS number when reporting position after call.
55.00.18.Rev.02
1.6.11_R.23 		2021.05.13
  • No changes
  • Fixed issue which occurred during manufactory testing phase with Ver.55.00.18.Rev.01 where device could end with GNSS State = 0
55.00.18.Rev.01
1.6.11_R.23 		2021.05.07
  • Increased Beacon List from 25 to 100
  • Added On Demand Tracking On/Off/Switch button action
  • Added On Demand Tracking event indication settings
  • Increased Configured beacons count from 25 to 100
  • If Beacon record sending is configured to be 'Eventual', send only if device sees any beacons
  • Improved Power On/Off feature notifications
  • Power save mode is working with Data Acquisition time 60s and above
  • On Demand Tracking functionality improved with button control and On Demand Tracking event indication
55.00.10.Rev.01
1.6.11_R.16 		2020.11.13
  • Added Last Known Position feature settings
  • Added Power On/Off event settings
  • Added Power off with Power key settings
  • Added Custom BLE I/O parameters
  • Added Last Known Position feature on HIGH priority event (alarm, amber alert, man-down, etc).
  • When device gains current GPS position after HIGH priority event was generated, device sends another HIGH priority event with updated position and GPS fix timestamp.
  • Reworked GNSS status SMS template.
  • Fixed issue of data acquisition parameters reset to default values.
55.00.07.Rev.09
1.5.15_C.002 		2020.10.20
  • Minor changes
  • Important change of charging algorithm. This algorithm provides higher safety and prolonging battery’s life longevity.
  • Corrected battery display in percentage
  • Improved charging current from PC.
55.00.07.Rev.07
1.5.15_C.002 		2020.09.16
  • Minor changes
  • Lowered battery charging current from wall charger to 425mA.
  • Fixed battery LED indication when battery is fully charged.
55.00.07.Rev.02
1.5.15_C.002 		2020.03.17
  • Added Man-Down Event On Exit and On Entrance parameters
  • Updated Server IP and Port saving procedures.
  • Reworked Generate Event On Exit and On Entrance logic.
  • Reworked handheld devices switching between Charging and Normal modes.
  • Reworked User ID values scan after device is turn off/on.
  • Reworked Button I/O on-click event.
55.00.05.Rev.00
1.5.0_C.007 		2020.02.13
  • Removed unnecessary Low Power parameters
  • Removed unnecessary Time Synchronization settings
  • Implemented On Demand tracking functionality
  • Removed unnecessary Number Check Settings panel
  • Implemented Event Notification functionality
  • Implemented User ID functionality
  • Improved BLE beacon functionality
  • Implemented Beacon List functionality
  • Improved User Interface configuration panel
  • Improved Keyboard configuration panel
  • Implemented Button IO feature
  • Updated default settings
  • Reworked User Interface configuration.
  • Reworked Keyboard configuration.
  • Implemented Event Notification panel.
  • Implemented Call After Answer functionality
  • Implemented User ID functionality.
  • Implemented On Demand data acquisition functionality.
  • Implemented Button IO Feature.
  • Optimized wake up from deep sleep by movement.
  • Updated default settings.
  • Improved BLE compatibility with beacons.

GH5200

Base

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.02.03.Rev.05
1.7.66 B.55.2 R.10 		2024-01-30
  • [CHN] Added new AVL ID's SMS events tab
  • [FIX] Fixed Online vs Offline configuration discrepancies
  • [FIX] Fixed Ultra Deep Sleep naming mismatch
  • [FIX] Fixed Tool Tips inaccuracies
  • [ADD] Added EYE Sensors support settings and filtering by sensors name and MAC address
  • [CHN] Changed device wiki links to teltonika-gps
  • [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab
  • [FIX] Fixed Roaming operator/Operator Black List .csv file importing
  • [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
  • [ADD] Added configurable accelerometer sensitivity settings
  • [ADD] Added continuous battery charging mode
  • [CHN] Changed minimum BLE scan start period value
  • [CHN] Added possibility to send SMS AVL ID event to few numbers
  • [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
  • [ADD] Added CSQ level parameter
  • [FIX] Fixed Event Notification SMS text maximum length
  • [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
  • [ADD] Added configurable accelerometer sensitivity options in sleep mode
  • [FIX] Fixed ‚btgetlist 3‘ SMS command
  • [FIX] Changed battery voltage measurement and charging algorithm
  • [ADD] Added EYE Sensor support
  • [ADD] BLE sensors Custom field data are displayed in decimal now
  • [FIX] Fixed batteries percentage calculation when voltage is Fully charged
  • [ADD] Added " dropcall" SMS command to hang up the call.
  • [ADD] Added call duration limits for Alarm event
  • [ADD] Added Call duration limits for each keyboard button
  • [FIX] Fixed call and SMS send issue for Feature>>Event notification
  • [FIX] Refactored battery percentage limits checking algorithm
  • [FIX] Fixed battery charging status
  • [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
  • [ADD] Added ability to switch audio to Bluetooth headset/speaker with a button.
  • [FIX] Fixing issue when incoming call voice audio doesn't work via HFP
  • [FIX] AXL and LIS3DH changes to prevent unwanted wake up from sleep mode and prevent fake movement detection
  • [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
  • [FIX] Fixed GSM established LED indication turning off issue
  • [CHN] Changed minimum BLE scan start period configuration value.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.02.03.Rev 05
1.7.66_B.55.2_R.10 		2023-12-13
  • [CHN] Added new AVL IDs SMS events tab
  • [FIX] Fixed Online vs Offline configuration discrepancies
  • [FIX] Fixed Ultra Deep Sleep naming mismatch
  • [FIX] Fixed Tool Tips inaccuracies
  • [ADD] Added EYE sensors support settings and filtering by sensor's'name and MAC address
  • [CHN] Changed device wiki links to teltonika-gps
  • [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab.
  • [FIX] Fixed Roaming operator/Operator Black list .csv file importing
  • [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
  • [ADD] Added configurable accelerometer sensitivity settings
  • [ADD]Added events call duration limits
  • [ADD]Added call duration limits for keyboard buttons independently.
  • [ADD] Added continuous battery charging mode
  • [CHN] Changed minimum BLE scan start period value.
  • [CHN] Added possibility to send SMS AVL ID event to few numbers
  • [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
  • [ADD] Added CSQ level parameter
  • [FIX] Fixed Event Notification SMS text maximum length
  • [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
  • [ADD] Added configurable accelerometer sensitivity options in sleep mode
  • [FIX] Fixed ‚btgetlist 3‘ SMS command
  • [FIX] Changed battery voltage measurement and charging algorithm
  • [ADD] Added EYE sensor support
  • [ADD] BLE sensors Custom field data are displayed in decimal now
  • [FIX] Fixed batteries percentage calculation when voltage is Fully charged
  • [ADD] Added " dropcall" SMS command to hang up the call.
  • [ADD] Added call duration limits for Alarm event
  • [ADD] Added Call duration limits for each keyboard button
  • [FIX] Fixed call and SMS send issue for Feature>>Event notification
  • [FIX] Refactored battery percentage limits checking algorithm
  • [FIX] Fixed battery charging status
  • [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
  • [ADD] Added ability to switch audio to Bluetooth headset/speaker with a button.
  • [FIX] Fixing issue when incoming call voice audio doesn't work via HFP
  • [FIX] AXL and LIS3DH changes to prevent unwanted wake up from sleep mode and prevent fake movement detection
  • [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
  • [FIX] Fixed GSM established LED indication turning off issue
  • [CHN] Changed minimum BLE scan start period configuration value.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.01.02.Rev.01
1.6.11_R.30 		2021.10.25
  • Change No Movement/Movement event SMS text
  • Added Race Mode feature
  • Added Race Mode for GNSS data live tracking
  • Fixed LED indication stuck when Man-Down Cancel button is pressed
  • Fixed FW version display in FOTA WEB
  • Fixed possibility to configure forbidden GNSS source via SMS or GPRS
  • Fixed fake movement events when Low power mode is used
  • Fixed BLE scan stuck when Xiaomi bracelet is used
  • Fixed restarts when Beacon on Demand feature is used for longer time
  • Fixed Alarm call delay issue
  • Fixed FW update issue with XT26G01CWSIGT flash
  • Added XT26G01CWSIGT and GD5F1GQ5UE NAND flash support
  • Changed minimum charging temperature from -10°C to 1°C
  • SMS commands will return time with applied time zone
  • The maximum battery charging temperature changed from 50°C to 45°C
  • Maximum operating temperature changed from 65°C to 59°C
55.00.21.Rev.00
1.6.11_R.26 		2021.08.10
  • Added Tool tips information about Beacon record mode 'No Send'.
  • 'Data Acquisition' tool tips and labels changed.
  • Changed BLE 'Update frequency' name and tool tips.
  • Amber Alert tool tip changes.
  • Amber Alert timeout name changed.
  • Xiaomi Mi Band 2 support.
  • Added possibility to Enable or Disable Mandown/Movement/No Movement features while charging.
  • Fixed invalid SMS number when reporting position after call.
  • Accelerometer improvements.
  • Minor changes
55.00.18.Rev.02
1.6.11_R.23 		2021.05.13
  • No changes
  • Fixed issue which occurred during manufactory testing phase with Ver.55.00.18.Rev.01 where device could end with GNSS State = 0
55.00.18.Rev.01
1.6.11_R.23 		2021.05.07
  • Increased Beacon List from 25 to 100
  • Added On Demand Tracking On/Off/Switch button action
  • Added On Demand Tracking event indication settings
  • Enabled vibration for Call Active indication.
  • Increased Configured beacons count from 25 to 100
  • If Beacon record sending is configured to be 'Eventual', send only if device sees any beacons
  • Improved Power On/Off feature notifications
  • Power save mode is working with Data Acquisition time 60s and above
  • On Demand Tracking functionality improved with button control and On Demand Tracking event indication
  • ManDown functionality was improved with additional sensing methods. First one FreeFall sensing and other FreeFall with Angle combination
  • Mandown Cancel button functionality added
  • Fixed constant or uncontrolled Battery LED On state
  • Added configurable outgoing alarm tone sound
55.00.13.Rev.00
1.6.11_R.18 		2021.01.14
  • Added GNSS Fix Holdout settings
  • Added Outgoing Call in loudspeaker settings
  • Added No movement pre-alarm indication settings
  • Added Power off button disable feature.
  • Special function added: GPS search on hold for 30 seconds.
  • Fixed Power on/off event feature.
  • Changed Call logic between simultaneous alarms.
  • Fixed device Power on from USB, when feature is disabled.
  • Added possibility to update GNSS coordinate every 1sec.
  • Safe charging improvements.
  • Reworked On Demand Tracking.
  • Changed Call and SMS logic for Man-Down feature.
55.00.10.Rev.01
1.6.11_R.16 		2020.11.13
  • Added Last Known Position feature settings
  • Added Power On/Off event settings
  • Added amber alert feature settings (for GH5200)
  • Added Amber alert indication (for GH5200)
  • Added Amber alert settings on a keyboard (for GH5200)
  • Added Power off with Power key settings
  • Added Custom BLE I/O parameters
  • Added Man-Down Event On Exit and On Entrance parameters
  • Added Amber Alert feature with configurable event Timeout and pre-alarm.
  • Improved ManDown, AutoGeofence, Alarm button and Amber Alert maximum call list to 10 numbers.
  • Changed outgoing call indication to vibration only.
  • Added Last Known Position feature on HIGH priority event (alarm, amber alert, man-down, etc.)
  • When GH5200 gains current GPS position after HIGH priority event was generated, device sends another HIGH priority event with updated position and GPS fix timestamp.
  • Added outgoing call in loudspeaker mode once the call is established.
  • Reworked GNSS status SMS template.
55.00.05.Rev.01
1.5.0_C.007 		2020.03.06
  • Removed unnecessary Low Power parameters
  • Removed unnecessary Time Synchronization settings
  • Implemented On Demand tracking functionality
  • Removed unnecessary Number Check Settings panel
  • Implemented Event Notification functionality
  • Implemented User ID functionality
  • Improved BLE beacon functionality
  • Implemented Beacon List functionality
  • Improved User Interface configuration panel
  • Improved Keyboard configuration panel
  • Implemented Button IO feature
  • Updated default settings
  • Reworked factory test tool.
55.00.05.Rev.00
1.5.0_C.007 		2020.02.13
  • Removed unnecessary Low Power parameters
  • Removed unnecessary Time Synchronization settings
  • Implemented On Demand tracking functionality
  • Removed unnecessary Number Check Settings panel
  • Implemented Event Notification functionality
  • Implemented User ID functionality
  • Improved BLE beacon functionality
  • Implemented Beacon List functionality
  • Improved User Interface configuration panel
  • Improved Keyboard configuration panel
  • Implemented Button IO feature
  • Updated default settings
  • Reworked User Interface configuration.
  • Reworked Keyboard configuration.
  • Implemented Event Notification panel.
  • Implemented Call After Answer functionality
  • Implemented User ID functionality.
  • Implemented On Demand data acquisition functionality.
  • Implemented Button IO Feature.
  • Optimized wake up from deep sleep by movement.
  • Updated default settings.
  • Improved BLE compatibility with beacons.

Proximity

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.01.02.Rev.200
1.5.15_C.232 		2021.11.15
  • Fixed In Use satellites not display issue
  • Add missing parameter IDs in tooltips
  • Added XT26G01CWSIGT and GD5F1GQ5UE NAND flash support
  • The maximum battery charging temperature changed from 50°C to 45°C
  • Maximum operating temperature changed from 65°C to 59°C
  • Fixed Remote Connection indication.
  • SMS commands will return time with applied time zone
  • Fixed FW version display in FOTA WEB
  • Fixed SMS send and Call issue, when GPRS send period is set to 0 sec.
  • Changed minimum charging temperature from -10°C to 1°C
  • Fixed configuration saving error. Which was happening due FW version change
  • Increased BLE scan stability.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.00.08.Rev.349
1.5.15_C.228 		2021.05.07
  • Added configurable Proximity indication pause
  • Added option 'Advertise only' for proximity while charging
  • Added configurable Proximity indication pause.
  • Changed default Scan Window and Scan Interval
  • Added option 'Advertise only' for proximity while charging
  • Corrections for data sending via RUTX
  • If Beacon record sending is configured to be 'Eventual', send only if device sees any beacons
55.00.08.Rev.344
1.5.15_C.225 		2021.01.14
  • Added Proximity Violator type iBeacon
  • Improved proximity feature stability.
  • Reworked device connection with RUTX.
  • Improved proximity advertising scanning stability.
  • Safe charging improvements for GH5200.
  • Added feature which allows to use Beacons with proximity feature.
  • Fixed device Power on from USB, when feature is disabled.
  • Proximity improvements to support several devices at the same time.
55.00.08.Rev.337
1.5.15_C.222 		2020.10.23
  • Added Proximity with RUTX setting
  • Added Proximity RDDI exit threshold setting
  • Added Proximity RDDI moving average samples setting
  • Improved RSSI level calculation logic, averaging according to configurated sample size was implemented.
  • Added BLE advertising interval parameter.
  • Added duplicate scan filter to improve BLE performance.
55.00.08.Rev.335
1.5.15_C.219 		2020.10.09
  • Added Teltonika beaons setting
  • Improved BLE power level parameters.
  • Added Proximity RSSI exit threshold parameter.
  • Added Proximity RSSI moving average parameter.
  • Reworked generation of Proximity records.
  • Changed Proximity record priority from Low to High.
  • Reworked Proximity record sending according to Data Acquisition.
55.00.08.Rev.334
1.5.15_C.219 		2020.09.28
  • Added Teltonika beaons setting
  • Added new beacon detection option Teltonika (device only detects Teltonika devices).
  • Improved Proximity detection, works with Beacon Detection All and Beacon Detection Teltonika settings.
  • Improved Proximity contact duration calculation.
  • Improved Beacon detection stability.
55.00.08.Rev.332
1.5.15_C.217 		2020.09.28
  • Added Home Zone on Exit on entrance settings
  • Improved Proximity record sending.
  • Reworked Home Zone on exit and on entrance event generation.
  • Improved Power Off event delay.
  • Corrected Power On/Off event logic.
  • Reworked Proximity SMS, IMEI is sent instead of BLE MAC
  • Proximity Service ID was removed.

TAT100

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.569

BlueNRG version: 10.0.3.Rev.00 for TAT100 HW ver.: 31
1.0.3.Rev.00 for TAT100 HW ver.: 62
Configurator version: 1.7.74_E.TAT1_R.7

2024.08.19
  • Added an option to configure TLS functionality.
  • Added an option to configure SMS record sending.
  • Added an option to configure MQTT Azure and AWS support.
  • Added an option to configure I am alive feature.
  • Added TLS functionality feature.
  • Added SMS record sending feature.
  • Added MQTT Azure and AWS support.
  • Added I am alive feature.
  • Fixed X, Y and Z IO elements not being included with First Power On record.
  • Extended On Stop and On Move periodic timers to maximum value of 7 days.
  • Improvements to Static Navigation logic in no GPS situation.
  • New AVL ID 69 value added (4 - no GPS in Static Navigation).
  • Improved Recovery mode trigger logic in Lost Sensor scenario.
  • Added error code when BLE sensor is lost.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.564

BlueNRG version: 10.4.12 for TAT100 HW ver.: 31
0.4.12 for TAT100 HW ver.: 62
Configurator version: 1.7.74_B.TAT1_R.6

2024.03.12
  • Fixed configurator crash after firmware update.
  • Added cell ID I/O elements
  • Fixed error when disabling BLE features in configuration.
  • Added GSM area code I/O element
  • Simplified EYE sensor configuration.
  • Added Autonomous Alarm System feature.
  • Fixed periodic timer starting in Recovery mode.
  • Improved backup tracker scan procedure.
  • Fixed issue with GPS fix with First Power On record.
  • Improved energy management in sleep mode when device is in motion.
  • Fixed crash on BLE sensor alarm.
  • Bluetooth scanning and data parsing optimization.
  • DNS resolve improvements.
  • Fixed periodic timer starting when tracking scenario selected as None.
  • Changed default movement sensitivity to 150 mG
  • Changed default GNSS mode to GLONASS, GPS and GALILEO
  • Fixed EYE sensor data multiplier for correct data displaying.
  • Fixed issue if GPRS is lost during record sending.
  • Fixed GPRS command processing in UDP mode.
  • Improved received SMS reading process.
  • Improved connection to Fota process.
  • Fixed BLE sensor data not being included in periodic records.
  • Improved static navigation logic.
  • Improved Bluetooth scan stability.
  • Added BLE beacons for Recovery mode trigger.
  • Movement logic rework.
  • Added condition to stop GNSS search if less than 3 satellites found in the first 60 seconds.
Firmware version: 55.00.16.Rev.545

BlueNRG version: 10.3.12 for TAT100 HW ver.: 31
0.3.12 for TAT100 HW ver.: 62
Configurator version: 1.7.16_E.TAT100.R23 RELEASE

2022.08.23
  • No changes
  • Fixed issue with incorrectly detected SIM slot for eSIM devices.
Firmware version: 55.00.16.Rev.543
BlueNRG version: 10.3.12 for TAT100 HW ver.: 31
0.3.12 for TAT100 HW ver.: 62
Configurator version: 1.7.16_E.TAT100.R23 RELEASE 		2022.08.08
  • Updated Teltonika Configurator version to set Central device default IMEI to 300000000000000
  • Added Recovery mode option
  • Added I/O element of Recovery Mode
  • Added more options of movement sensitivity threshold [50-1000mG]
  • Configurator for BLE FW and Backup FW was merged into one.
  • SMS command created for getting device statistics
  • Protection from writing other devices FW
  • Added condition to prevent modem waking up at midnight if scheduler is configured
  • Added reconfiguration mechanism that lets FW work with / without SMPS filterMissing
  • Fixed issue of missing 4th sensor's data with Monitoring operand
  • Fixed too frequent / unnecessary scans with all sensors configured as monitoring
  • Fixed sensors scan starting with monitoring operand when Backup tracker is configured
  • Backup tracker scan not starting right after
  • Time synchronization every 24 hours
  • Fixed LBS data sending issue
  • New AVL ID 20015 for Modem UpTime (in seconds)
  • Added response sending if recovery command is sent through GPRS
  • The next periodic record after Recovery mode deactivation being sent with AVL ID 20012 - fixed
  • Reduced EQ Core update frequency
  • Fixed battery consumption issue when GSM is jammed.
  • LED status changed from constant on to blinking mode to save the battery
  • Added Recovery mode feature
  • Implemented Recovery mode activation from the Backup tracking alarm
  • Added EYE sensors support
  • Fixed Minor bugs regarding the sensors
  • Fixed Short period Recovery Mode records
  • Extended Backup Tracker: Central device IMEI range
  • Backup tracker: Scanning logic has been changed, scan duration is not configurable anymore, it is up to 60 seconds by default now.
  • Implemented Record timestamp shift feature
  • Fixed BLE sensor records with wrong event ID being sent
  • Fixed BLE sensor record duplicates with On change operand
  • Fixed BLE sensor On Exit record not generating when switching to sleep mode
  • Fixed Custom1 sensor data in SMS being sent as NaN (empty)
  • Fixed duplicate BLE sensor data after waking up
  • Changed required packets amount in backup tracker scenario and minimal scan duration
  • Fixed backup tracker alarm not triggering just before wakeup
  • Fixed backup tracker not detecting enough packets during BLE scan
  • Periodic records do not affect backup tracker alarm record generation
Firmware version: 55.00.16.Rev.522
BlueNRG version: 10.2.21.Rev.01
Configurator version: 1.7.16_R.TAT100.R2 		2021.12.21
  • Improved battery safety features
  • Fixed stuck download during FOTA update
  • Fixed device not restarting to update FW after FOTA download
  • Improved main device packet filtering
  • Improved battery voltage measurement
  • Fixed the device not restarting after FOTA WEB update when it happens at the same time as periodic record
  • Fixed random statistic losses
  • Fixed GNSS module status not being accurate in Teltonika Configurator
  • Improved static navigation mode
  • Fixed scheduler time resync timer not working properly
  • Fixed statistic not being deleted from RAM
Firmware version: 55.00.15.Rev.519
BlueNRG version: 10.2.14
Configurator version: 1.7.16_R.TAT100.R2 		2021.10.19
  • Fixed fake movement detection on startup
  • Fixed problem when the device is stuck in On Stop tracking mode after reconfiguration
  • Added Power-On reason data and fixed version changes to device statistics
  • Fixed Backup tracker issue where the alarm mode is not immediately activated when the central device disappears
  • Fixed empty GSM I/O elements
  • Fixed an issue where UTC is added after each reconfiguration
  • Added record printing to Dump log
  • LBS data is not included in records if GNSS fix was caught
  • Fixed NTP timesync failure if offset is zero
  • Improved record creation (wake up from sleep) during Backup tracker alarms



  • Improved GNSS module control with Static Navigation and LBS
  • Added prevention from inappropriate record generation if the battery is low (HW watchdog)
  • Added statistic element for USB connected uptime
  • Added timestamp to BlueNRG serial prints
  • Minor improvement for BlueNRG firmware update via configurator
  • Added filter for LBS cell_id duplicates
  • Improved Bluetooth sensor record creation with 'On Change' operand
  • Added Bluetooth sensor support
  • Added condition to skip LBS data update if location source is only GNSS
  • Increased retries of AT+# command in order to avoid empty LBS data from modem
  • Changed Open link timeout to 15s
  • Fixed an issue where the tracking mode would change from the scheduler to periodic
  • Improved logic for multiple FOTA Web tasks update in the same connection
  • Implemented rule for additional connection to FOTA Web after baseband firmware update
  • Added accelerometer version information inside '.info' serial command
  • Fixed an issue with battery voltage I/O element when record saving is overlapping with a firmware update
  • Fixed Scheduler record sending at midnight
  • Fixed missed LBS values inside I/O elements
  • Fixed an issue when GNSS speed is not zero while the device is in a stationary position
  • General minor improvements
55.00.10.Rev.509
BlueNRG: 10.2.3_Rev.00
1.7.16_E.TAT100_04 		2021.05.10
  • Added Test Connection button
  • Temporarily removed Secondary Server Settings
  • Tracking Period default value changed to 28800 (s)
  • Implemented Test Connection feature.
  • Added BlueNRG logging to DUMP files
  • Added LBS data logging to DUMP files
  • Added protection that blocks FMB firmware flash to AT devices
  • Added time-sync update with asset purpose command
  • Improved periodic record timer logic
  • Improved battery voltage measurement
  • Improved periodic GPRS data sending while USB is connected to the device
  • Disabled SMPS filter
  • Fixed record sending when movement is triggered at all times
  • Improved NTP time-sync
55.00.05.Rev.510
BlueNRG: 0.1.7 		2020.12.03
  • Removed tracking scenarios
  • Removed speed source parameter
  • Removed record saving/sending without TS parameter
  • Removed LED Indication parameter
  • Removed NTP resync parameter
  • Implemented FOTA support.
  • Improved GNSS position capturing.
  • Reworked Periodic and Scheduler tracking counters.
  • Implemented device logging via USB.
  • Implemented statistics acquisition to flash memory.
55.00.05.Rev.507
BlueNRG: 0.1.5 		2020.09.29
  • Implemented GNSS Source configuration. Available options: BeiDou, GLONASS, Galileo and GPS.
  • Added I/O elements: Data Mode, GSM Signal, GNSS Status, GNSS PDOP, GNSS HDOP, Speed, GSM Cell ID, GSM Area Code, Battery Voltage, Active GSM Operator, ICCID, Coordinates ISO6709.
  • Added SMS command autorization via Login and Password logic.
  • Implemented 'Codec 8', 'Codec 8 Extended' and 'Codec 12' protocols.
  • Implemented NTP, NITZ and GNSS time synchronization sources.
  • Implemented ability to send GPRS data from device via TCP or UDP channels.
  • Implemented connection to server timeouts.
  • Ported TLS encryption functionality from other Teltonika devices.
  • Implemented Periodic and Scheduler tracking.
  • Implemented BlueNRG firmware update via GPRS. This function will be used to reflash BlueNRG firmware via FOTA WEB.
  • Added GSM number authorization logic.

TAT140

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.569

BlueNRG version: 1.0.3.Rev.00
Configurator version: 1.7.74_E.TAT1_R.7

2024.08.19
  • Added an option to configure TLS functionality.
  • Added an option to configure SMS record sending.
  • Added an option to configure MQTT Azure and AWS support.
  • Added an option to configure I am alive feature.
  • Added TLS functionality feature.
  • Added SMS record sending feature.
  • Added MQTT Azure and AWS support.
  • Added I am alive feature.
  • Fixed X, Y and Z IO elements not being included with First Power On record.
  • Extended On Stop and On Move periodic timers to maximum value of 7 days.
  • Improvements to Static Navigation logic in no GPS situation.
  • New AVL ID 69 value added (4 - no GPS in Static Navigation).
  • Improved Recovery mode trigger logic in Lost Sensor scenario.
  • Added error code when BLE sensor is lost.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.564
BlueNRG version: 0.4.12
Configurator version: 1.7.74_B.TAT1_R.6 		2024.03.12
  • Fixed configurator crash after firmware update.
  • Added cell ID I/O elements
  • Fixed periodic timer starting in Recovery mode.
  • Improved backup tracker scan procedure.
  • Fixed issue with GPS fix with First Power On record.
  • Improved energy management in sleep mode when device is in motion.
  • Fixed crash on BLE sensor alarm.
  • Bluetooth scanning and data parsing optimization.
  • DNS resolve improvements.
  • Fixed periodic timer starting when tracking scenario selected as None.
  • Added cell ID I/O elements
Firmware version: 55.00.16.Rev.558
BlueNRG version: 0.4.8
Configurator version: 1.7.16_B.TAT1_R.3 		2023.07.18 * Removed non configurable elements
  • [FIX] Improved EYE sensor data detection to be suitable for all sensor modes
  • [FIX] Fixed Periodic timer still running when Recovery mode is activated in sleep from Backup tracker
  • [FIX] Hotfix for EG915ULA modem status commands
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.557
BlueNRG version: 0.4.7
Configurator version: 1.7.16_B.TAT1_R.1 		2023.05.10 Initial release Initial release

TAT141

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.569

BlueNRG version: 1.0.3.Rev.00
Configurator version: 1.7.74_E.TAT1_R.7

2024.08.19
  • Added an option to configure TLS functionality.
  • Added an option to configure SMS record sending.
  • Added an option to configure MQTT Azure and AWS support.
  • Added an option to configure I am alive feature.
  • Added TLS functionality feature.
  • Added SMS record sending feature.
  • Added MQTT Azure and AWS support.
  • Added I am alive feature.
  • Fixed X, Y and Z IO elements not being included with First Power On record.
  • Extended On Stop and On Move periodic timers to maximum value of 7 days.
  • Improvements to Static Navigation logic in no GPS situation.
  • New AVL ID 69 value added (4 - no GPS in Static Navigation).
  • Improved Recovery mode trigger logic in Lost Sensor scenario.
  • Added error code when BLE sensor is lost.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.564
BlueNRG version: 0.4.12
Configurator version: 1.7.74_B.TAT1_R.6 		2024.03.12
  • Fixed configurator crash after firmware update.
  • Added cell ID I/O elements
  • Fixed periodic timer starting in Recovery mode.
  • Improved backup tracker scan procedure.
  • Fixed issue with GPS fix with First Power On record.
  • Improved energy management in sleep mode when device is in motion.
  • Fixed crash on BLE sensor alarm.
  • Bluetooth scanning and data parsing optimization.
  • DNS resolve improvements.
  • Fixed periodic timer starting when tracking scenario selected as None.
  • Added cell ID I/O elements
Firmware version: 55.00.16.Rev.558
BlueNRG version: 0.4.8
Configurator version: 1.7.16_B.TAT1_R.3 		2023.07.18 * Removed non configurable elements
  • [FIX] Improved EYE sensor data detection to be suitable for all sensor modes
  • [FIX] Fixed Periodic timer still running when Recovery mode is activated in sleep from Backup tracker
  • [FIX] Hotfix for EG915ULA modem status commands


VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.557
BlueNRG version: 0.4.7
Configurator version: 1.7.16_B.TAT1_R.1 		2023.05.10 Initial release Initial release

TAT240

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.569

BlueNRG version: 1.0.3.Rev.00
Configurator version: 1.7.74_E.TAT1_R.7

2024.08.19
  • Added an option to configure TLS functionality.
  • Added an option to configure SMS record sending.
  • Added an option to configure MQTT Azure and AWS support.
  • Added an option to configure I am alive feature.
  • Added an option to configure SMS alert on Tamper event.
  • Added SMS alert on Tamper event feature.
  • Fixed X, Y and Z IO elements not being included with First Power On record.
  • Extended On Stop and On Move periodic timers to maximum value of 7 days.
  • Improvements to Static Navigation logic in no GPS situation.
  • New AVL ID 69 value added (4 - no GPS in Static Navigation).
  • Improved Recovery mode trigger logic in Lost Sensor scenario.
  • Added error code when BLE sensor is lost.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
Firmware version: 55.00.16.Rev.564
BlueNRG version: 0.4.12
Configurator version: 1.7.74_B.TAT1_R.6 		2024.03.12
  • No changes
  • Fixed periodic timer starting in Recovery mode.
  • Improved backup tracker scan procedure.
Firmware version: 55.00.16.Rev.562
BlueNRG version: 0.4.11
Configurator version: 1.7.74_B.TAT1_R.6 		2023.12.20
  • Initial release
  • Initial release
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Stable_Firmware_%26_Software_CHANGELOG&oldid=94816#TAT240"