Difference between revisions of "Secure vehicle disabling"

From Wiki Knowledge Base | Teltonika GPS
m (Protected "Secure vehicle disabling" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite)))
(39 intermediate revisions by 8 users not shown)
Line 1: Line 1:
+
==Project description==
==Introduction==
 
 
Motor vehicle theft is one of the world’s biggest concerns and the fastest growing crimes in many countries around the world. This great challenge for car rental agencies, car sharing clubs, businesses, state organizations and private car owners caused properly losses of over 6 billion US dollar globally in 2018. Luckily for them, Teltonika GPS trackers gave a remote secure engine cut-off (SECO) functionality that can help to recover a stolen vehicle and prevent the loss.
 
Motor vehicle theft is one of the world’s biggest concerns and the fastest growing crimes in many countries around the world. This great challenge for car rental agencies, car sharing clubs, businesses, state organizations and private car owners caused properly losses of over 6 billion US dollar globally in 2018. Luckily for them, Teltonika GPS trackers gave a remote secure engine cut-off (SECO) functionality that can help to recover a stolen vehicle and prevent the loss.
  
Line 7: Line 6:
 
Here you will find how to prepare and to test this solution.
 
Here you will find how to prepare and to test this solution.
  
==Solution description==
 
From the firmware version '''03.28.02''' Secure vehicle disabling was introduced. This solution is intended to stop the stolen vehicle regardless of the thief's actions. Best way to do so is to disable fuel pump in order to prevent vehicle to be driven further away. However, disconnecting fuel pump on high speed will definitely cause an accident and innocent people may be harmed.
 
 
Therefore we came up with a logic how to force vehicle to stop without causing an accident. Pulsing digital output disables fuel pump in intervals until vehicle slows down to configured speed from which pump is fully disabled.
 
 
==What you need for a solution?==
 
==What you need for a solution?==
  
*The secure vehicle disabling solution is supported by '''any Teltonika FMB series tracker (excluding FMX640 series trackers) which has''' one or more '''digital output''' (DOUT) which in this scenario is used to control fuel pump of the car.
+
* The secure vehicle disabling solution is supported by any Teltonika FMB series tracker which has one or more digital output (DOUT) which in this scenario is used to control fuel pump of the car.  
*The SIM card in order to get data to your server.
+
* The SIM card in order to get data to your server.
*[[Automotive_Relay|Automotive Relay]] to cut off the fuel pump
+
* The secure engine cut-off (SECO) functionality is only available in Teltonika FMB series GPS trackers starting with the firmware version 03.25.10.Rev.110 or higher.
*The secure engine cut-off (SECO) functionality is only available in Teltonika FMB series GPS trackers starting with the firmware version 03.28.02.
+
* FOTA WEB to remotely send the configuration to the device.
*FOTA WEB to remotely send the configuration to the device.
 
  
 
==Installation==
 
==Installation==
It’s important to well hide tracker, so it would not be a simple task for the thieves to find and unplug it. But also, please do not forget to follow [https://wiki.teltonika-gps.com/view/FMB130_First_Start#Mounting_recommendations mounting recommendations] as well. [[File:Wiring scheme.png|alt=|right|frameless|357x357px]]
+
It’s important to well hide tracker, so it would not be a simple task for the thieves to find and unplug it. But also, please do not forget to follow [https://wiki.teltonika-gps.com/view/FMB130_First_Start#Mounting_recommendations mounting recommendations] as well. Although devices have high gain antennas it’s important to mount devices with stickers on top and in metal-free space. The device should be firmly fixed to the surface or cables. Please make sure, that device is not fixed to heat emitting or moving parts.
 
 
Although devices have high gain antennas it’s important to mount devices with stickers on top and in metal-free space. The device should be firmly fixed to the surface or cables. Please make sure, that device is not fixed to heat emitting or moving parts.
 
  
  
Line 31: Line 23:
 
*The ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
 
*The ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
  
== Configuration==
+
==Configuration==
  
==='''1. Prerequisites:'''===
+
===1. Prerequisites:===
 
====1.1. Read through [https://wiki.teltonika-gps.com/view/FMB130_First_Start First start guide]====
 
====1.1. Read through [https://wiki.teltonika-gps.com/view/FMB130_First_Start First start guide]====
 
====1.2. Understanding of possible [https://wiki.teltonika-gps.com/view/FMB130_System_settings#Sleep_Mode Sleep modes].====
 
====1.2. Understanding of possible [https://wiki.teltonika-gps.com/view/FMB130_System_settings#Sleep_Mode Sleep modes].====
  
 
==='''2. Configuring SECO scenario'''===
 
==='''2. Configuring SECO scenario'''===
<br>
 
[[File:GPRS settings.png|alt=|left|257x257px|thumb]]
 
Parameter ID - Parameter name GPRS settings:<br>
 
*<span style="background-color:#91b9d4;">2001</span> – APN
 
*<span style="background-color:#91d4b9;">2002</span> – APN username (if there are no APN username, empty field should be left)
 
*<span style="background-color:#b991d4;">2003</span> – APN password (if there are no APN password, empty field should be left)
 
<br>
 
<br>
 
<br>
 
<br>
 
<br>
 
[[File:SERVER settings.png|alt=|left|258x258px|thumb]]Server settings:
 
*<span style="background-color:#b9d491;">2004</span> – Domain
 
*<span style="background-color:#d491b9;">2005</span> – Port
 
*<span style="background-color:#d4b991;">2006</span> – Data sending protocol (0 – TCP, 1 – UDP)<br>
 
<br>
 
<br>
 
<br>
 
After successful GPRS/SERVER settings configuration, FMB130 device will '''synchronize time''' and '''update records''' to '''the configured server'''. Time intervals and default I/O elements can be changed by using [[Teltonika Configurator]] or [[FMB920 Parameter list|SMS parameters]].
 
<br>
 
<br>
 
[[File:Codec 8E.png|alt=|left|frame]]
 
System settings:
 
<br>
 
*<span style="background:#E18DE7">113</span> - Data protocol (0 – Codec 8, 1 – Codec 8 Extended)
 
<br>
 
[[File:Sleep_mode.png|alt=|left|thumb]]
 
<br>
 
Sleep settings:
 
*<span style="background:#05CC6F">102</span> – Sleep settings (0 – Disable, 1 – Gps sleep, 2 – Deep sleep, 3 – Online Deep sleep, 4 – Ultra sleep)
 
<br>
 
<br>
 
<br>
 
<br>
 
<br>
 
<br>
 
<br>
 
'''Note''': This scenario will not work with [[FMB130 Sleep modes#Deep%20Sleep%20mode|Deep Sleep]] and [[FMB130 Sleep modes#Ultra%20Deep%20Sleep%20mode|Ultra Deep Sleep]] since they disable the device's GSM module to save power.
 
<br>
 
<br>
 
[[File:SECO.png|alt=|left|451x451px|thumb]]
 
SECO scenario settings:
 
<br>
 
*<span style="background:#E18DE7">12250</span> – Scenario priority (0 - Disable, 1 - Low, 2 - High, 3 - Panic).
 
*12251 – Eventual settings (0 – Disable, 1 – Enable), if disabled - scenario status value will be appended in each AVL record.
 
*<span style="background:#24FFD4">12252</span> – Output Control (0 – None, 1 – DOUT1, 2 – DOUT2, 3 – DOUT3)
 
* 12254 - Speed (km/h). Digital output will be activated if vehicle speed consistently lower than configured during "Speed check period".
 
* 12259 - Speed Pulse Scenario (km/h). Valid if "Output Pulse" feature enabled. Scenario will be activated if vehicle speed consistently lower than configured during "Speed check period". After activation digital output will be activated and disabled continuously until speed will be lower then configured in "Speed" field and longer then "Speed check period".
 
*12255 - Speed check period (s). Time span during which vehicle speed must be lower than configured for output to activate.
 
*12256 - Movement timeout (s). Accelerometer's instant movement timeout after which output will be activated (GNSS OFF).
 
*12253 - Output Pulse (0 – Disable, 1 – Enable). Pulse scenario adds additional output control which helps to slow down vehicle before fully disabling fuel pump.
 
*12257 – DOUT ON Duration (ms)
 
* 12258 – DOUT OFF Duration (ms)
 
*7377 – Send SMS To
 
*8377 – SMS text<br>
 
  
  
 +
Parameter ID - Parameter name GPRS settings:
 +
[[File:GPRS settings.png|frameless|alt=|left|250x250px]]
  
 +
GPRS Settings:
  
 +
*<span style="background-color:#91b9d4;">2001</span> – APN
 +
*<span style="background-color:#91d4b9;">2002</span> – APN username (if there are no APN username, empty field should be left)
 +
*<span style="background-color:#b991d4;">2003</span> – APN password (if there are no APN password, empty field should be left)
  
 +
[[File:SERVER settings.png|frameless|alt=|left|250x250px]]
  
 +
Server settings:
  
<br>
+
*<span style="background-color:#b9d491;">2004</span> Domain
'''Quick start''': From default configuration to SECO detection in one SMS:
+
*<span style="background-color:#d491b9;">2005</span> Port
"  setparam <span style="background-color:#91b9d4;">2001</span>:APN;<span style="background-color:#91d4b9;">2002</span>:APN_username;<span style="background-color:#b991d4;">2003</span>:APN_password;<span style="background-color:#b9d491;">2004</span>:Domain;<span style="background-color:#d491b9;">2005</span>:Port;<span style="background-color:#d4b991;">2006</span>:0;<span style="background:#E18DE7">113</span>:1;<span style="background:#05CC6F">102</span>:1;<span style="background:#E18DE7">12250</span>:2;<span style="background:#24FFD4">12252</span>:1"
+
*<span style="background-color:#d4b991;">2006</span> – Data sending protocol (0 – TCP, 1 – UDP)
This SMS will set up your device for Secure Vehicle Disabling scenario - remote secure engine cut-off (SECO) functionality.
 
  
'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.
 
  
==SECO SMS Commands==
+
After successful GPRS/SERVER settings configuration, FMB130 device will '''synchronize time''' and '''update records''' to '''the configured server'''. Time intervals and default I/O elements can be changed by using [[Teltonika Configurator]] or [[FMB920 Parameter list|SMS parameters]].<br />
  
 +
[[File:SystemsettingsSECO.png|frameless|alt=|left|622x622px]]
  
Secure engine cut-off (SECO) functionality is available for device with at least one DOUT.  For SECO functionality to work, DOUT must to be selected. SECO has DOUT control priority higher than immobilizer scenario.
 
  
 +
System settings:
  
SECO scenario can only be enabled or disabled by SMS commands:
+
* 100 - Movement source
 +
* 133 - Speed source
  
*"secoon" - to activate SECO functionality.
+
* 107 - Records Saving/Sending Without TS
 +
* 108 - LED Indication
 +
* 109 - GNSS Source
 +
* 110 - Battery Charge mode
 +
* 111 - Analog Input Value Range
 +
* <span style="background:#E18DE7">113</span> - Data protocol
  
*"secooff" - to disable SECO functionality.
+
[[File:Sleep_mode.png|alt=|frameless|left|250x250px]]
  
  
The structure of sending SMS commands: [[FMB130 SMS/GPRS Commands]]
+
Sleep settings:
  
=== 1. SMS responses===
+
*<span style="background:#05CC6F">102</span> – Sleep settings(0 – Disable, 1 – Gps sleep, 2 – Deep sleep, 3 – Online Deep sleep, 4 – Ultra sleep)
 +
*.<br />
  
  
To SMS command „secooff“ device will give response: „Seco off received. DOUTX off“.
 
  
To SMS command „secoon“ response:
 
  
1. „Seco on received. Waiting for conditions“.
+
'''Note''': This scenario will not work with [[FMB130 Sleep modes#Deep%20Sleep%20mode|Deep Sleep]] and [[FMB130 Sleep modes#Ultra%20Deep%20Sleep%20mode|Ultra Deep Sleep]] since they disable the device's GSM module to save power
  
2. „Seco on received. DOUTX pulsing“.
+
[[File:SECO.png|alt=|frameless|left|445x445px]]
  
3. „Seco on received. DOUTX on“.
+
SECO scenario settings:
  
When response is not 3 all later SMS will be received. Example: SMS 1 received and pulse configured, then SMS 2 will be received when speed is lower than configured and SMS 3 will be received when speed reaches 0 km/h.
+
*<span style="background:#E18DE7">12250</span> – Scenario priority
 +
*12251 – Eventual settings (0 – Disable, 1 – Enable)
 +
*<span style="background:#24FFD4">12252</span> – Output Control (0 – None, 1 – DOUT1, 2 – DOUT2, 3 – DOUT3)
 +
*12254 - Speed (km/h)
 +
*12259 - Speed Pulse Scenario (km/h)
 +
*12255 - Speed check period (s)
 +
*12256 - Movement timeout (s)
 +
*12253 - Output Pulse (0 – Disable, 1 – Enable)
 +
*12257 – DOUT ON Duration (ms)
 +
*12258 – DOUT OFF Duration (ms)
 +
*7377 - Send SMS To
 +
*8377 – SMS text
 +
<br />
 +
<br />
 +
<br />
 +
<br />
  
 +
<br />'''Quick start''': From default configuration to SECO detection in one SMS:
  
'''Note:'''  Sending commands to the device without DOUT will give response "SECO not available for this device". When DOUT is not selected in configuration response will be: "Error. no DOUT configured".
+
"  setparam <span style="background-color:#91b9d4;">2001</span>:APN;<span style="background-color:#91d4b9;">2002</span>:APN_username;<span style="background-color:#b991d4;">2003</span>:APN_password;<span style="background-color:#b9d491;">2004</span>:Domain;<span style="background-color:#d491b9;">2005</span>:Port;<span style="background-color:#d4b991;">2006</span>:0;<span style="background:#E18DE7">113</span>:1;<span style="background:#05CC6F">102</span>:1;<span style="background:#E18DE7">12250</span>:2;<span style="background:#24FFD4">12252</span>:1"
  
===2. SECO Pulse functionality===
+
==Pharsing SECO records==
 
 
 
 
 
 
In case SECO pulse (12253) is enabled device will not activate DOUT immediately.
 
 
 
'''GNSS fix present''': when speed is lower than configured Speed Pulse Scenario (12259) for configured amount of time (12255), device will pulse DOUT until GNSS speed reaches configured speed (12254) then DOUT will stop pulsing and stay active (ON) until „secooff“ SMS is received.
 
 
 
 
 
'''GNSS fix unavailable:''' wait until movement timeout (12256) is reached then DOUT will stay active until „secooff“ SMS is received.
 
 
 
In case SECO pulse is disabled while pulsing, device will activate DOUT.
 
 
 
===3. GNSS fix available===
 
 
 
 
 
After "secoon" SMS is received, command will be saved to the device memory and check vehicle speed. When speed is lower than configured (12254) for configured amount of time (12255), device will activate configured DOUT.
 
 
 
===4. GNSS fix unavailable===
 
 
 
 
 
After "secoon" SMS is received, command will be saved to device memory and movement timeout. When movement timeout (12256) is reached, device will activate configured DOUT.
 
 
 
==Parsing information==
 
  
 
==='''1.Prerequisites:'''===
 
==='''1.Prerequisites:'''===
Line 170: Line 112:
  
 
==== 1.2. Go to [[Java Parser First Start Guide|Java parser first start guide]]====
 
==== 1.2. Go to [[Java Parser First Start Guide|Java parser first start guide]]====
 
+
'''2. Parsing example:'''
==='''2. Parsing example:'''===
 
 
{| class="nd-othertables_2" style="width:100%;"
 
{| class="nd-othertables_2" style="width:100%;"
 
|+
 
|+
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
+
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" | Unparsed received data in hexadecimal stream
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |00000000000000678E02000001774D66D5A8010F1267D220979FC600BE00C1050028<span style="background:#0b9768">018C</span>0004000400EF0100
 
| style="vertical-align: middle; text-align: center;" |00000000000000678E02000001774D66D5A8010F1267D220979FC600BE00C1050028<span style="background:#0b9768">018C</span>0004000400EF0100
Line 234: Line 175:
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |1’st IO ID
 
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |00 EF (AVL ID: 239; Name: Ignition)
+
| style="vertical-align: middle; text-align: center;" | 00 EF (AVL ID: 239; Name: Ignition)
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |1’st IO Value
 
| style="vertical-align: middle; text-align: center;" |1’st IO Value
Line 240: Line 181:
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
 
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |00 F0 (AVL ID: 240; Name: Movement)
+
| style="vertical-align: middle; text-align: center;" | 00 F0 (AVL ID: 240; Name: Movement)
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
 
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
Line 303: Line 244:
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |1’st IO ID
 
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |00 EF (AVL ID: 239; Name: Ignition)
+
| style="vertical-align: middle; text-align: center;" | 00 EF (AVL ID: 239; Name: Ignition)
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |1’st IO Value
 
| style="vertical-align: middle; text-align: center;" |1’st IO Value
Line 309: Line 250:
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
 
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |00 F0 (AVL ID: 240; Name: Movement)
+
| style="vertical-align: middle; text-align: center;" | 00 F0 (AVL ID: 240; Name: Movement)
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
 
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
Line 339: Line 280:
 
|-
 
|-
 
| style="vertical-align: middle; text-align: center;" |Number of Data 2 (Number of Total Records)
 
| style="vertical-align: middle; text-align: center;" |Number of Data 2 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |02
+
| style="vertical-align: middle; text-align: center;" | 02
 
|-
 
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
+
| style="vertical-align: middle; text-align: center;" | CRC-16
 
| style="vertical-align: middle; text-align: center;" |00 00 A6 5F
 
| style="vertical-align: middle; text-align: center;" |00 00 A6 5F
 
|}
 
|}
  
==Demonstration in platform==
+
==In platform ==
 
TAVL: Open TAVL → select client → select Street Map → select device → choose the date from which to which to show the records → push advanced → push show button and then you will see in left down corner all information.
 
TAVL: Open TAVL → select client → select Street Map → select device → choose the date from which to which to show the records → push advanced → push show button and then you will see in left down corner all information.
 
+
[[File:Seco 2.png|alt=|frameless|center|1155x1155px]]
 
+
<br />
[[File:Tavl Seco 1.png|alt=|frameless|1153x1153px]]
+
[[File:Seco 2.png|alt=|frameless|center|1155x1155px]]
 
 
 
 
[[File:Tavl Seco 2.png|alt=|frameless|1153x1153px]]
 
 
 
 
 
WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to show the records → select message  (data messages) → push execute button and you will see all information.
 
 
 
 
 
[[File:Wialon Seco 1.png|alt=|frameless|1153x1153px]]
 
 
 
[[File:Wialon Seco 2.png|alt=|frameless|1153x1153px]]
 
<br>
 
<br>
 
[[Category: Usage scenarios]]
 

Revision as of 21:44, 18 February 2021

Main Page > General Information > Usage scenarios > Secure vehicle disabling

Project description

Motor vehicle theft is one of the world’s biggest concerns and the fastest growing crimes in many countries around the world. This great challenge for car rental agencies, car sharing clubs, businesses, state organizations and private car owners caused properly losses of over 6 billion US dollar globally in 2018. Luckily for them, Teltonika GPS trackers gave a remote secure engine cut-off (SECO) functionality that can help to recover a stolen vehicle and prevent the loss.

We glad that you decided to test our “Secure vehicle disabling” solution.

Here you will find how to prepare and to test this solution.

What you need for a solution?

  • The secure vehicle disabling solution is supported by any Teltonika FMB series tracker which has one or more digital output (DOUT) which in this scenario is used to control fuel pump of the car.
  • The SIM card in order to get data to your server.
  • The secure engine cut-off (SECO) functionality is only available in Teltonika FMB series GPS trackers starting with the firmware version 03.25.10.Rev.110 or higher.
  • FOTA WEB to remotely send the configuration to the device.

Installation

It’s important to well hide tracker, so it would not be a simple task for the thieves to find and unplug it. But also, please do not forget to follow mounting recommendations as well. Although devices have high gain antennas it’s important to mount devices with stickers on top and in metal-free space. The device should be firmly fixed to the surface or cables. Please make sure, that device is not fixed to heat emitting or moving parts.


During installation please follow recommendations in order to avoid damaging device and vehicle:

  • Wires should be connected while the module is not plugged in.
  • Be sure that after the car computer falls asleep, power is still available on the chosen wire. Depending on the car, this may happen in a 5 to 30 minutes period.
  • When the module is connected, be sure to measure the voltage again if it did not decrease.
  • The ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.

Configuration

1. Prerequisites:

1.1. Read through First start guide

1.2. Understanding of possible Sleep modes.

2. Configuring SECO scenario

Parameter ID - Parameter name GPRS settings:

GPRS Settings:

  • 2001 – APN
  • 2002 – APN username (if there are no APN username, empty field should be left)
  • 2003 – APN password (if there are no APN password, empty field should be left)

Server settings:

  • 2004 – Domain
  • 2005 – Port
  • 2006 – Data sending protocol (0 – TCP, 1 – UDP)


After successful GPRS/SERVER settings configuration, FMB130 device will synchronize time and update records to the configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters.


System settings:

  • 100 - Movement source
  • 133 - Speed source
  • 107 - Records Saving/Sending Without TS
  • 108 - LED Indication
  • 109 - GNSS Source
  • 110 - Battery Charge mode
  • 111 - Analog Input Value Range
  • 113 - Data protocol


Sleep settings:

  • 102 – Sleep settings(0 – Disable, 1 – Gps sleep, 2 – Deep sleep, 3 – Online Deep sleep, 4 – Ultra sleep)
  • .



Note: This scenario will not work with Deep Sleep and Ultra Deep Sleep since they disable the device's GSM module to save power

SECO scenario settings:

  • 12250 – Scenario priority
  • 12251 – Eventual settings (0 – Disable, 1 – Enable)
  • 12252 – Output Control (0 – None, 1 – DOUT1, 2 – DOUT2, 3 – DOUT3)
  • 12254 - Speed (km/h)
  • 12259 - Speed Pulse Scenario (km/h)
  • 12255 - Speed check period (s)
  • 12256 - Movement timeout (s)
  • 12253 - Output Pulse (0 – Disable, 1 – Enable)
  • 12257 – DOUT ON Duration (ms)
  • 12258 – DOUT OFF Duration (ms)
  • 7377 - Send SMS To
  • 8377 – SMS text






Quick start: From default configuration to SECO detection in one SMS:

"  setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0;113:1;102:1;12250:2;12252:1"

Pharsing SECO records

1.Prerequisites:

1.1. Open TCP/UDP port

1.2. Go to Java parser first start guide

2. Parsing example:

Unparsed received data in hexadecimal stream
00000000000000678E02000001774D66D5A8010F1267D220979FC600BE00C1050028018C0004000400EF0100

F00100B300018C010000000000000000000001774D66D990010F12663120979BFF00BE00C1050028018C0004

000400EF0100F00100B300018C020000000000000000020000A65F

AVL Data Packet
AVL Data Packet Part HEX Code Part
Zero Bytes 00 00 00 00
Data Field Length 00 00 00 67
Codec ID 8E (Codec 8 Extended)
Number of Data 1 (Records) 02
Timestamp 00 00 01 77 4D 66 D5 A8 (Friday, January 29, 2021 9:08:41 AM)
Priority 01
Longitude 0F 12 67 D2
Latitude 20 97 9F C6
Altitude 00 BE
Angle 00 C1
Satellites 05
Speed 00 28
Event IO ID 01 8C (AVL ID: 396, Name: Seco)
of Total ID 00 04
of One Byte IO 00 04
1’st IO ID 00 EF (AVL ID: 239; Name: Ignition)
1’st IO Value 01
2’nd IO ID 00 F0 (AVL ID: 240; Name: Movement)
2’nd IO Value 01
3’th IO ID 00 B3 (AVL ID: 179; Name: Digital Output 1)
3’th IO Value 00
4’th IO ID 01 8C (AVL ID: 396, Name: Seco)
4’th IO Value 01 ( 0 - SECO DOUT OFF; 1- SECO DOUT pulsing; 2 - SECO DOUT ON)
N2 of Two Bytes IO 00 00
N4 of Two Bytes IO 00 00
N8 of Two Bytes IO 00 00
NX of X Byte IO 00 00
Timestamp 00 00 01 77 4D 66 D9 90 (Friday, January 29, 2021 9:08:42 AM)
Priority 01
Longitude 0F 12 66 3
Latitude 20 97 9B FF
Altitude 00 BE
Angle 00 C1
Satellites 05
Speed 00 28
Event IO ID 01 8C (AVL ID: 396, Name: Seco)
of Total ID 00 04
of One Byte IO 00 04
1’st IO ID 00 EF (AVL ID: 239; Name: Ignition)
1’st IO Value 01
2’nd IO ID 00 F0 (AVL ID: 240; Name: Movement)
2’nd IO Value 01
3’th IO ID 00 B3 (AVL ID: 179; Name: Digital Output 1)
3’th IO Value 00
4’th IO ID 01 8C (AVL ID: 396, Name: Seco)
4’th IO Value 02 ( 0 - SECO DOUT OFF; 1- SECO DOUT pulsing; 2 - SECO DOUT ON)
N2 of Two Bytes IO 00 00
N4 of Two Bytes IO 00 00
N8 of Two Bytes IO 00 00
NX of X Byte IO 00 00
Number of Data 2 (Number of Total Records) 02
CRC-16 00 00 A6 5F

In platform

TAVL: Open TAVL → select client → select Street Map → select device → choose the date from which to which to show the records → push advanced → push show button and then you will see in left down corner all information.