Difference between revisions of "NBL-2"
m (Text replacement - "Bluetooth(?!®)" to "Bluetooth®") |
m |
||
| (19 intermediate revisions by 2 users not shown) | |||
| Line 4: | Line 4: | ||
'''Description:''' | '''Description:''' | ||
| − | Netronix NBL-2 - wireless | + | Netronix NBL-2 - wireless RFID reader with Bluetooth. |
'''NBL-2 is great in these use cases:''' | '''NBL-2 is great in these use cases:''' | ||
| − | * Authorized driving - track who is driving your vehicle | + | * Authorized driving - keep track of who is driving your vehicle according to the NBL-2 ID they use to authenticate themselves. |
| − | * Private mode – | + | * Private mode – gives the ability to mask all the personal data while the vehicle is used in Private mode. |
| − | ''' | + | '''Functionality:''' |
| − | * | + | * Unpaired reader (state after default reset) is waiting for button only |
| − | * | + | * Reader scans for transponder detect or button press all time when is paired |
| − | * | + | * In the case previously mentioned events occur, the reader sends an advertising packet for Ta time in period Tb. Defaults: Ta=50sec, Tb=100ms |
| − | * | + | * During advertising green led is flashing slowly. The reader stops blinking and advertising after disconnection. |
| − | * | + | * Depending on the configuration, read card ID can be present on the advertising packet or/and on characteristic |
| − | * | + | * Reader closes the connection and goes into low power 50 seconds after the last data exchange. |
| − | * | + | * Each LED can be controlled on GATT services |
| − | * | + | * Reader can be on/off by long button press |
| + | * Reader performs sensor measurement in a period that is configurable | ||
| + | * Button reacts immediately | ||
| + | * Sensors configuration is set by GATT services. | ||
| + | * Detecting the start and stop of the vehicle. This mode is active immediately after turning on the device.<br /> | ||
==Product Specification== | ==Product Specification== | ||
{| class="wikitable" | {| class="wikitable" | ||
| + | |Operating frequency | ||
| + | |13,56MHz | ||
| + | |- | ||
| + | |Supported standards | ||
| + | |MIFARE® Classic | ||
| + | MIFARE® DESFire | ||
| + | |- | ||
| + | |Interface | ||
| + | |Bluetooth | ||
|- | |- | ||
|Supply voltage | |Supply voltage | ||
| Line 36: | Line 49: | ||
|Size (mm) | |Size (mm) | ||
|58 x 99 x 19 | |58 x 99 x 19 | ||
| − | |||
| − | |||
| − | |||
|- | |- | ||
|Type | |Type | ||
| Line 44: | Line 54: | ||
|} | |} | ||
| − | ==NBL-2 | + | ==NBL-2 configuration== |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
'''1. Updating NBL-2''' | '''1. Updating NBL-2''' | ||
| − | Go to NBL Tools application -> Device -> Characteristic -> Device Information Service -> Firmware Revision String. | + | First, you have to make sure that NBL-2 firmware version is updated to 1.3. Go to NBL Tools application -> Device -> Characteristic -> Device Information Service -> Firmware Revision String. |
[[File:NBL_conf1.jpg.jpg|alt=|frameless|520x520px]] [[File:NBL_conf2.jpg.jpg|alt=|border|frameless|520x520px]] [[File:NBL_conf3.jpg.jpg|alt=|frameless|519x519px]] | [[File:NBL_conf1.jpg.jpg|alt=|frameless|520x520px]] [[File:NBL_conf2.jpg.jpg|alt=|border|frameless|520x520px]] [[File:NBL_conf3.jpg.jpg|alt=|frameless|519x519px]] | ||
| Line 77: | Line 81: | ||
[[File:NBL conf7.jpg.jpg|frameless|520x520px]] | [[File:NBL conf7.jpg.jpg|frameless|520x520px]] | ||
| − | 5. Wake up the device - | + | 5. Wake up the device - eg entering it into the bootloader mode. |
| − | 6. Select the device from the list, then select Update firmware from the drop-down menu and press the Start button. | + | 6. Select the device from the list (long press), then select Update firmware from the drop-down menu and press the Start button. |
[[File:NBL conf9.jpg.jpg|frameless|520x520px]] [[File:NBL conf8.jpg.jpg|frameless|519x519px]] | [[File:NBL conf9.jpg.jpg|frameless|520x520px]] [[File:NBL conf8.jpg.jpg|frameless|519x519px]] | ||
7. Correct firmware update will be signaled by device start-up led message. | 7. Correct firmware update will be signaled by device start-up led message. | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==Device configuration== | ==Device configuration== | ||
| − | + | Setting up NBL-2 device to connect with FMB device. Go to Teltonika configurator -> Bluetooth 4.0 and set it up like it shown in this screenshot (MAC address will depend on your particular NBL sensor): | |
| − | |||
| − | Setting up NBL-2 device to connect with FMB device. | ||
| − | |||
| − | Go to Teltonika configurator -> | ||
[[File:Nbl2 1.png|frameless|660x660px]] | [[File:Nbl2 1.png|frameless|660x660px]] | ||
| Line 125: | Line 99: | ||
Then go to I/O settings: | Then go to I/O settings: | ||
| − | Make sure to enable | + | Make sure to enable BLE RFID #1 parameter (ID: 51740) and set the operand to „On Change“. |
[[File:Nbl2 3.png|frameless|999x999px]] | [[File:Nbl2 3.png|frameless|999x999px]] | ||
| Line 144: | Line 118: | ||
==Testing NBL-2== | ==Testing NBL-2== | ||
| − | + | Power up the FMB device and start logging it into the Terminal application. When the RFID card is not enabled, the BLE RFID #1 parameter (AVL ID: 451) will show a specific value. Example: | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | Power up the FMB device | ||
| − | |||
| − | When the RFID card is not enabled, the BLE RFID #1 parameter (AVL ID: 451) will show a specific value. | ||
| − | |||
| − | Example: | ||
''IO ID[451]: 0x0000000000000000'' | ''IO ID[451]: 0x0000000000000000'' | ||
| Line 183: | Line 136: | ||
==NBL-2 packet== | ==NBL-2 packet== | ||
NBL-T data is being read via broadcast packets only. The packet structure is described below: | NBL-T data is being read via broadcast packets only. The packet structure is described below: | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | [[File:NBL conf 13.png|frameless]] | |
| − | + | ||
| − | + | ||
| − | | | + | 0x02010606094E424C2D540CFF4E58 A7CB250501B01A0047 |
| − | + | ||
| − | + | '''Table No. 1.''' Parsed broadcast packet | |
| − | |||
| − | |||
| − | |||
{| class="wikitable" | {| class="wikitable" | ||
| − | + | |'''Type''' | |
| − | + | |'''HEX Value''' | |
| − | + | |'''ASCII Value''' | |
| − | + | |'''Description''' | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
|- | |- | ||
| − | | | + | |09 |
| − | | | + | |4E424C2D540C |
| − | | | + | |NBL-T |
| − | | | + | |Complete Local name |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
|- | |- | ||
| − | | | + | |FF |
| − | | | + | |4E58 A7CB250501B01A 00 47 |
| − | | | + | |1. UUID – 2 bytes |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | 2. RFID Id – 7 bytes | |
| − | + | 3. Button status – 1 byte | |
| − | + | 4. Battery level – 1 byte (%) | |
| + | |Manufacturer data | ||
| + | |} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
[[Category:Accessories]] | [[Category:Accessories]] | ||
Revision as of 16:34, 25 November 2022
Main Page > Accessories > NBL-2Introduction to the product
Description:
Netronix NBL-2 - wireless RFID reader with Bluetooth.
NBL-2 is great in these use cases:
- Authorized driving - keep track of who is driving your vehicle according to the NBL-2 ID they use to authenticate themselves.
- Private mode – gives the ability to mask all the personal data while the vehicle is used in Private mode.
Functionality:
- Unpaired reader (state after default reset) is waiting for button only
- Reader scans for transponder detect or button press all time when is paired
- In the case previously mentioned events occur, the reader sends an advertising packet for Ta time in period Tb. Defaults: Ta=50sec, Tb=100ms
- During advertising green led is flashing slowly. The reader stops blinking and advertising after disconnection.
- Depending on the configuration, read card ID can be present on the advertising packet or/and on characteristic
- Reader closes the connection and goes into low power 50 seconds after the last data exchange.
- Each LED can be controlled on GATT services
- Reader can be on/off by long button press
- Reader performs sensor measurement in a period that is configurable
- Button reacts immediately
- Sensors configuration is set by GATT services.
- Detecting the start and stop of the vehicle. This mode is active immediately after turning on the device.
Product Specification
| Operating frequency | 13,56MHz |
| Supported standards | MIFARE® Classic
MIFARE® DESFire |
| Interface | Bluetooth |
| Supply voltage | two AAA batteries |
| Sensor | Accelerometer
Low battery voltage |
| Operating temperature | -20ºC to +70ºC |
| Size (mm) | 58 x 99 x 19 |
| Type | RFID reader |
NBL-2 configuration
1. Updating NBL-2
First, you have to make sure that NBL-2 firmware version is updated to 1.3. Go to NBL Tools application -> Device -> Characteristic -> Device Information Service -> Firmware Revision String.
Note: If the firmware version is 1.1 or 1.0, it is not possible to update it.
If it is 1.2, then update NBL-2 according to these steps:
1. Run the NBL Tools application
2. Update the firmware database (tap: Manager Firmware -> Update the database -> Start). Select NBL-2 and check 1.3 firmware version.
3. Back to the main menu.
4. Tap the Device option.
5. Wake up the device - eg entering it into the bootloader mode.
6. Select the device from the list (long press), then select Update firmware from the drop-down menu and press the Start button.
7. Correct firmware update will be signaled by device start-up led message.
Device configuration
Setting up NBL-2 device to connect with FMB device. Go to Teltonika configurator -> Bluetooth 4.0 and set it up like it shown in this screenshot (MAC address will depend on your particular NBL sensor):
Mandatory setting condition: Non Stop Scan
Then go to I/O settings:
Make sure to enable BLE RFID #1 parameter (ID: 51740) and set the operand to „On Change“.
Setting up Private/Business mode
Make sure to enable Private/Business mode in Trip/Odometer settings. It can be done using SMS commands or a configurator. Not every device has these parameters visible in the configurator, therefore they should be configured via SMS commands. It can be done by sending setparam SMS (how to send SMS commands: https://wiki.teltonika-gps.com/view/FMB120_SMS/GPRS_Commands). Set it to High or Low priority (parameter ID: 11850). Enable triggers as NBL-1 Button1 or NBL-1 Button2 (parameter ID: 11811).
Don't forget to set up data masking in Private mode if necessary.
Don‘t forget to save all these changes to the device and you are ready to test the NBL-2 sensor.
More information about Private/Business Driving Mode Functionality.
Testing NBL-2
Power up the FMB device and start logging it into the Terminal application. When the RFID card is not enabled, the BLE RFID #1 parameter (AVL ID: 451) will show a specific value. Example:
IO ID[451]: 0x0000000000000000
When the RFID card is activated (card touched to NBL-2 and followed by two beeps) BLE RFID #1 parameter should look like this:
IO ID[451]: 0x0004193EF2576680
When Private/Business mode is enabled (Button1 or Button2 is pressed):
IO ID[451]: 0x0000000000000000
and
IO ID[391]: 1
NBL-2 packet
NBL-T data is being read via broadcast packets only. The packet structure is described below:
0x02010606094E424C2D540CFF4E58 A7CB250501B01A0047
Table No. 1. Parsed broadcast packet
| Type | HEX Value | ASCII Value | Description |
| 09 | 4E424C2D540C | NBL-T | Complete Local name |
| FF | 4E58 A7CB250501B01A 00 47 | 1. UUID – 2 bytes
2. RFID Id – 7 bytes 3. Button status – 1 byte 4. Battery level – 1 byte (%) |
Manufacturer data |
