Difference between revisions of "ECAN02"
From Wiki Knowledge Base | Teltonika GPS
Line 198: | Line 198: | ||
|} | |} | ||
− | == | + | ==Additional information== |
+ | |||
[https://teltonika-gps.com/products/trackers/can-obd-data/ecan02 ECAN02 Teltonika] | [https://teltonika-gps.com/products/trackers/can-obd-data/ecan02 ECAN02 Teltonika] | ||
+ | |||
+ | {{{EOL|For EOL policy please refer to link [https://teltonika-gps.com/support/eol-products here].}}} | ||
[[Category:CAN Trackers & Adapters]] | [[Category:CAN Trackers & Adapters]] |
Revision as of 15:43, 7 October 2024
Main Page > CAN Trackers & Adapters > ECAN02ECAN02 is contactless adapter used to read vehicle CAN Bus data. ECAN02 adapter should be used in combination with:
- LV-CAN200
- ALL-CAN300
- FMB140, FMB150, FMC150, FMM150
- FMB640, FMB630, FM6320, FM6300 to read J1939 CAN data.
It reads can-bus data through the isolation of wires without damaging them and forwards signals to the tracking device.
Features
- ECAN02 collects vehicle data from CAN bus without damaging the wires
- Powered from an on-board power source
- Reads the signals through the isolation of CAN bus wires
- Easy to install and operate
YouTube
Technical features
PARAMETER | VALUE | ||||
---|---|---|---|---|---|
Minimum | Typical | Typical | Maximum | Unit | |
Supply Voltage | |||||
Supply Voltage (Recommended Operating Conditions) | +10 | +12 | +24 | +30 | V |
Current Consumption | |||||
Working Mode | 4.21 | mA | |||
Sleep Mode | 1.47 | mA | |||
Operating Temperature | |||||
Operating Temperature | -40 | +85 | °C | ||
Protection | |||||
Internal resettable fuse (max 33 V) | 750 | mA |
- Dimensions 39 x 12 x 19 mm
- CAN-BUS speeds up to 1000 kb/s
- Fuse is protecting devices from high current peaks. If the voltage exceeds 33V (i.e. 35V) then protection diode stabilizes device voltage to 33V and the current value will increase accordingly.
Pinout
PIN NUMBER | PIN NAME |
DESCRIPTION |
---|---|---|
1 | CAN L | (Blue) Connect to CAN L input of CAN BUS converter |
2 | CAN H | (White/Blue) Connect to CAN H input of CAN BUS converter |
3 | VCC | (RED) Power supply (10-30) V DC (+) |
4 | GND (-) | (Black) Ground wire (10-30) V DC (-) |
Wiring scheme
Setup ECAN02
- Gently open the ECAN02 cover using a plastic pry tool from both sides.
- Remove backing material on double-sided adhesive tape.
- Insert CAN wires. Please make sure that the correct slots are used (CAN High/CAN Low).
- Close the device.
- Device is ready-to-use.
Certification & Approvals
Memberships
Certification & Approvals
Nomenclature, classification codes
FAQ
- How to install ECAN02 with LV-CAN200/ALL-CAN300 using:
- FMB110
- FMB120
- FMB122
- FMB125
- FMB130
- FMC125
- FMC130
- FMC13A
- FMM125
- FMM130
- FMM13A
- FMB225
- FMB230
- FMC225
- FMC230
- FMM230
Product Change Notifications
ECAN02 Product Change Notifications
Promotional Material
Downloads
Manuals & Documentation
ECAN02 Datasheet (EN) | (Updated on: 2023-06-21) | |
ECAN02 flyer | (Updated on: 2023-06-22) | |
ECAN01 vs ECAN02 flyer | (Updated on: 2023-06-22) |
Additional information
For EOL policy please refer to link here.