| FIRMWARE VERSION |
RELEASE DATE |
CHANGES |
04.00.00.Rev.14
(recommended for FMC920, FMC880, FMC800) |
2025.07.01 |
- Corrected an issue in the factory test procedure where the modem on Quectel EG915U-based devices failed to recover the correct baud rate, causing delayed startup
|
04.00.00.Rev.13
(recommended for FMB900, FMB910, FMB920, FMC920, FMM920, FMT100, FMC880 (Quectel EG915U-EU), FMM880, FMC800, FMM800, FMM80A, FMB110, FMB120, FMB130, FMB202, FMB204, FMB230, FMC130 (MeiG SLM320-PE2C, SLM320-PE2H, SLM320-L16A, SLM320-L16B), FMC230, FMC234, FMM130 (Quectel BG95-M3), FMM230, FMB125, FMC125 (MeiG SLM320-PE2C, SLM320-PE2H, SLM320-L16A, SLM320-L16B), FMC225, FMB140) |
2025.05.26 |
- NEW! Major version updated to 4.0.0 and downgrade protection added
- NEW! Added support for FMC880, FMM880
- NEW! Added support for FMC800, FMM800, FMM80A
- NEW! Added support for FMC234
- NEW! Modem recovery mechanism to address modem hangs resulting from network issues or poor signal conditions
- NEW! Implemented support for encrypted CAN commands over Bluetooth
- NEW! Enhanced “Advanced Unplug Detection” with additional condition options for speed and delay
- NEW! Added Beacon option for “Authorized Read Notification” feature
- NEW! Added Dynamic Ground vector feature for more accurate accelerometer data
- NEW! Added “Window state” security state flag elements
- NEW! Enabled devices to send records to a duplicate server via TCP in Codec JSON, while the primary server uses MQTT with TLS encryption
- NEW! Enabled “Driving state” and “Driving records” I/O elements for FMC880/FMM880 devices
- NEW! Added a DIN3 option as a trigger for outgoing calls in HF settings
- NEW! Added "set calibration" command
- NEW! Added a new GNSS I/O status value '4' - GNSS ON with an active GNSS filter.
- NEW! “Stay Awake” parameter option added for “Sleep Mode”
- NEW! “DTC Request on Engine Start” feature to avoid conflicts with external diagnostic equipment
- NEW! Added support of PCB temperature I/O element for devices with NTC
- NEW! Added support for TCP BIN/ASCII data forwarding in JSON CODEC format
- CHANGED! Default logging filters updated
- CHANGED! Unplug detection events are allowed to be sent before device going to Low Power Mode
- CHANGED! Adjusted accelerometer sensitivity to be more suitable for crash detection
- CHANGED! Set GNSS jamming DOUT control to a higher priority over maintenance DOUT
- CHANGED! Modifications to calibration algorithm for greater accuracy
- CHANGED! BLE Advertising period changed to 500 ms
- CHANGED! Refactored the Immobilizer Authorized ID checking feature
- CHANGED! Conditions when device operation is prohibited updated
- CHANGED! Adjusted the operator ban list logic to have a search timeout of 5 minutes and a ban time of 30 minutes
- CHANGED! Incremental retry periods for AGPS EPO download to improve successful download time period
- CHANGED! Program number parameter ID 11120 size increased and max value to 99999
- CHANGED! Additional traces for GPS and GSM jamming status in device log
- CHANGED! Enabled band 26 selection for devices equipped with Quectel BG95-M3 modems
- Adjusted battery percentage table for FMC234
- Corrected the limit connections management in Low Power Mode
- Resolved issue where MCC calculation was done incorrectly forcing device to enter blocked state
- DualSIM switching process speed adjusted for devices with MeiG modems
- Improved socket status reading for BG9X modems to correcly handle data sending if socket is closed
- Corrected the byte inversion issue in 1-Wire Matrix (ReadROM) ID parsing
- Device abnormal working with dynamic bt name when using value of 16 characters with %imei function resolved
- Addressed issues where the device behaved abnormally after receiving a #FWD DAT command with the target set to Bluetooth and a NULL payload
- Fine-tuned the parsing for start and end delimiters in RS232 Delimiter mode to enhance functionality
- Fixed an issue where high priority records were not sent if a call was triggered by a feature activation
- Resolved an issue where link was not close properly sometimes after sending a record in Low Power Mode
- Enhanced the retry mechanism for SIM PIN entries if the initial attempt was unsuccessful
- Adjusted the saving of the Digital Output state post-firmware update when the inverted mode is selected
- Enabled missing CAN RSF parameters
- Resolved unexpected wake-ups from sleep due to repeated time-sync issues and server failures to close sockets correctly
- Patched the fail count algorithm for 1-wire data reading to improve stability
- Disallowed GSM updates during server response wait periods to prevent duplicate record sending in online deep sleep mode
- Removed disallowed MCCs (250, 257, 432, 368, 467) from the APN list
- Improved parsing of VIN and Trailer VIN values
- Resolved EYE Sensor filtering issue by MAC or Name when configuration parameter “Identifier” was changed
- Resolved an issue where UL202 record value was incorrectly parsed in device logs
- Changed the BLE advanced data offset type to signed to correct inaccuracies when negative offsets were used
- Updated the DOUT control from the Ignition FSM to prevent feature bypass when switching ignition on and off within 1 second
- Adjusted the conversion of EYE "Major" and "Minor" values, ensuring data is packed according to Bigger Endian format when "Lost&Found" record are generated
- Corrected a typographical error in the lvcangetinfo response
- Resolved an issue where the device was unable to enter sleep mode due to an NTP sync being stuck
- Fixed an issue where the first GPRS command was ignored after the device connected to a Backup Server
- Resolved an issue where DTC fault codes were not correctly packed into records for some EV and Hybrid vehicles
- Improved SIM switch logic in devices equipped with Quectel modems
- Removed an unnecessary filter for the instant movement element status
- Resolved an issue where private/business mode was not functioning according to the weekly schedule
- Improved device stability when NMEA logging is enabled via RS232 at 9600 baud
- Enhanced device stability when a 2kHz signal is detected by the device using "Advanced Pulse Counter" feature
- Resolved an issue where 2G devices could not open a socket for a period after disconnecting from the network due to poor network conditions
- Resolved an issue where duplicate records were created if UART communication with the modem stopped working while the device was in GNSS/ODS sleep mode and USB was connected
- Improved the handling of the socket closing for devices with MeiG modules when TLS and Deep Sleep are used
- Improved the stability of OBD dongle data reading after a Bluetooth module restart
- Resolved an issue where the device would sometimes fully wake up from Deep Sleep due to periodic record sending
- Resolved an issue where the "Advanced Pulse Counter" parameter ID 145 would not reset to default settings via configurator
- Resolved an issue where EYE Beacon flag 27 data voltage and temperature values was not included not into record when "Beacon Simple" mode was used
- Improved the accuracy of device tracking location in "Low Power Mode"
- Resolved an issue where the getinfo response was split into several SMS messages
- Improved device stability when Private Mode is triggered by Virtual DIN2
- Resolved an issue where firmware downloads would interrupt frequent record sending for devices with MeiG modules
- EYE sensors status are now shown correctly in device logs
- Resolved an issue where on random cases, a trip end event was received with the trip odometer already reset to 0
- Adjusted so that the movement off timeout would not reset after device restart
- Disabled unnecessary tasks to decrease current consumption in UDS mode
- Resolved an issue where the WD counter was not functioning as expected in ODS mode
- Reduced the delay for Immobilizer activation after waking up from sleep
- Resolved an issue where the GNSS module would not return to operation after being jammed
- Resolved an issue where the program number could not be changed sometimes with an SMS command
- Applied a patch to support APDU commands, preventing connectivity issues when the device uses specific SIMs and crosses borders
- Ensured odometer values are saved after a fix loss to prevent resetting when the device powers off
- Applied a patch so that timestamps in crash traces are calculated relative to the crash event, preventing trace damage if a time jump occurs during a crash
- Applied a patch to improve Bluetooth interface stability when detecting a large number of Beacons
- Resolved an issue where the "On-Demand Tracking", "Activation By" parameter ID 10992 would not reset to default via configurator
- Resolved an issue where EYE sensor I/O values would be included in the record even if the "Working Mode" parameter was configured as "Disabled"
- Movement will be accurately detected after the movement detection delay period, and not simultaneously with towing detection when it is activated
- Resolved an issue where the Immobilizer would not retrigger the Digital output immediately if the ignition was turned on for shorter than 1 second
- Adjusted the btgetlist 3 command to return a full scanned object list
- Resolved an issue where the "Odometer Calculation Source" parameter ID 11806 did not reset back to the default value when the configuration was reset
- Resolved an issue where Beacon info remained visible in the configurator UI even when detection was disabled
- Resolved an issue where the TTFF (Time to First Fix) result was sometimes reported as 0 even though a fix was acquired
- Resolved an issue where the Digital Output was not activated by the "Immobilizer" scenario when the "Ignition Off timeout" was set to longer than the "Sleep Timeout"
- Implemented a minor interface control tweak for 1-wire interface stability
- Removed unnecessary spam from device log prints
- Corrected the behavior to stop advertising BLE packets once a connection is established
- Resolved an issue where the device's 1-Wire interface functioned incorrectly if the 1-Wire in Sleep mode parameter value changed while the device was in sleep mode
- Resolved an issue where fake movement was detected due to incorrect GNSS speed data acquired from the GNSS module
- Tweaked the BLE GATTS disconnect process to enable correct disconnection
- Resolved an issue where devices in Deep Sleep mode would sometimes fail to report the disconnected status using MQTT
- Resolved an issue where devices with MeiG modules would repeat a call after the first one was rejected
- Resolved an issue where the Authorization ID List check by Beacon could not be configured for FMX1XY devices
- Inverted DOUT state no longer resets after a soft reset
- Resolved an issue where movement delay was not resetting correctly if the movement state changed
- Device external module startup time improved when waking from ODS
- Resolved an issue where logging to dump would stop after a soft reset.
- Resolved an issue where the FMX880 device would lose fix for a short amount of time
- Adjusted Watchdog behavior when the device is still connected to a network operator
- Beacon record generation now properly waits for the Bluetooth stabilization period
- Resolved an issue where devices with a Quectel module would save an incorrect timestamp when waking from GNSS sleep mode
- Resolved an issue where entering the Features paragraph in the configurator sets a new value for parameter 11703
- SIM detection and reading time improved for devices with Quectel BG95-M3 modules
- Improved battery percentage reading for FMB204 devices
- Adjusted communication with AG3335 to fix issues where FMX880 devices would sometimes take a longer period to acquire a GNSS fix
- Resolved an issue where the modem was not starting as expected when the device initiated record sending in Low Power mode
|
03.29.00.Rev.21
(recommended for FMB122, FMB125, FMM125, FMC125 (SLM320-LA, SLM320-E2, EC21-EC), FMC225, FMC920) |
2024.08.07 |
- Optimized the startup process of the network modules to improve pass-rate during manufacturing testing.
- Dual SIM switching enhancements to improve pass-rate during manufacturing testing.
- Return real SIM slot for factory testing commands.
|
03.29.00.Rev.18
(recommended for FMB209) |
2024.05.17 |
|
03.29.00.Rev.18
(recommended for FMT100, FMB900, FMB910, FMB920, FMC920, FMM920, FMB110, FMB120, FMB122, FMB130, FMC130 (SLM320-LA, SLM320-E2, EC21-EC, EC21-AU), FMC13A, FMM130 (BG95-M3, BG96), FMM13A, FMB202, FMB204, FMB206, FMB230, FMC230, FMM230, FMB140, FMB240, FMB125, FMC125 (SLM320-LA, SLM320-E2, EC21-EC), FMM125 (BG95-M3), FMB225, FMC225) |
2024.05.13 |
- Improved reconnection to new operator time if GPRS was unavailable with initial operator
- Fixed pro-longed reconnection to new operator due to record tasks interrupting operator search
- Fixed network session closing when current operator is added to blacklist
- Improved module initialization time for devices with Quectel modems
- Fixed Digital Output state restore after firmware update
- RS232 interface stability improvements
- GNSS status element state improvements
- Time synchronization improvements
- Manufacture testing improvements
|
03.29.00.Rev.263
((only for FMB209) |
2024.04.02 |
- Added support for use with FMB209 EU version
|
03.29.00.Rev.14
(recommended for FMM130 with BG95-M3, FMM230, FMC125 with MeiG SLM320, FMC225, FMC13A) |
2023.12.13 |
|
03.27.14.Rev.00
(recommended for FMB120, FMB130, FMB920) |
2022.11.01 |
- 1-wire interface optimization
- New accelerometer component support added
- Improved system stability and fixed general bugs
|
03.27.13.Rev.03
(recommended for FMT100, FMB1XY, FMB0XY, FMB2XY, FMB9XY, FMM130, FMC001) |
2022.08.01 |
- Improved system stability and fixed general bugs
|
03.27.13.Rev.01
(recommended for FMM001) |
2022.04.06 |
- Manufacture testing improvements
- Improved system stability and fixed general bugs
|
03.27.12.Rev.00
(recommended for FMC001) |
2022.02.09 |
- Preferred Operator functionality improvements
- SLM320 modem support added
- BLE advanced beacon improvements
- Static navigation improvements
- GNSS improvements
- New OBD Data MCU support added
- Improved system stability and fixed general bugs
|
03.27.07.Rev.00
(recommended for FMB9X0, FMB204, MTB100) |
2021.08.02 |
- New Flash memory component support added
- Inverted DOUT functionality added
- Universal Beacons functionality added
- Added Beacon On Change functionality
- Beacons list expanded to support 50 beacon ID's
- BLE AES128 encryption added
- Added Ignition On Counter functionality
- Added BLE Efento sensor support
- Added encrypted record support (TLS)
- Added Ban list control functionality
- EGTS protocol support added
- Added configurable ACK type (TCP/AVL) source feature
- Advanced eco driving for all hardware
- Matrix3 RFID support added
- iButton list extended to 4000 iButtons
- Device records saving/sending improvements
- Towing scenario improvements
- SMS Data Sending improvements on events generation
- SMS commands setdigout and readio sending improvements
- Time synch from NTP/NITZ improvements
- Device wake up from sleep modes improvements
- HW with eSIM feature general working improvements
- Can adapters data reading on ignition off/on improvements
- Can adapters settings over SMS commands improved
- General device debug logs capture improvements
- BLE whitelist (scan stability improvements)
- Battery protection improvements
- Improved system stability and fixed general bugs
|
03.25.18.Rev.08
|
2021.04.30 |
- internal GNSS chip firmware update
- Improved AutoAPN feature
|
03.25.18.Rev.05
|
2021.02.26 |
- AutoAPN improvements
- Odometer calculation from CAN adapters data improvements
- Improved system stability and fixed general bugs
|
03.25.18.Rev.03
|
2020.12.28 |
- Fix data type for BLE Sensor Custom
- Record data sending improvements
- Records saving and sending logic improved
- Improved system stability and fixed general bugs
|
03.25.15.Rev.32
|
2020.07.21 |
- Auto APN functionality added to base firmware.
|
03.25.15.Rev.02
(recommended for FM30XY) |
2020.02.17 |
- Improved Green Driving feature parameter sending.
|
03.25.15.Rev.01
|
2020.01.22 |
- Records saving and sending logic improved.
|
03.25.14.Rev.05
|
2019.12.23 |
- UL202 Fuel level sensor support improvements, status IO changed from (AVL ID 328) to (AVL ID 483)
- Odometer accuracy improvements when the Odometer Calculation Source is selected as the LVCAN
|
| 03.25.14.Rev.03 |
2019.11.27 |
|
| 03.25.07.Rev.00 |
2019.06.10 |
- One wire data reading improvements
- Manual geofence configuration improvements
- Data sending in online deep sleep mode optimization
- DOUT Control via Ignition implementation
- OBD data reading improvements
- SMS command btgetlist improvements
- Periodic sending optimization
- Changed setdigout command response to "DOUT is disabled from CFG" if DOUT is disabled configuration
- Improved SMS responses
|
| 03.25.05.Rev.00 |
2019.05.06 |
- Added FMB207 support
- Added FMB964 support
- Added FMB130 support
- Added BT3 auto connection mode "User ID"
- Added UL202-02 fuel sensors functionality
- Improved record sending to backup
- Added DOUT3 control for scenarios with FMB130 hardware
- Improved OBD CAN reading
- Add "Always" battery charge mode
- Added codec14 protocol support
- GPS Acquisition improvements
- Improved duplicate lvcan parameters
- OBDII improvements, for ignition off detection and protocol changing
- Add RS485 parity selection
- Improved ECO driving functionality I/O elements manipulation
- Added impulse counter support for FMB130
- Added FW downgrade protection
- Rename BT user ID I/O element text default value
- Added composed Bluetooth name functionality
- Changed minimum & default geofence zone radius to 5 meters
- GPS status update
- Improved Eco Driving detection for FMB20X devices
- Improved baud rate change
- Change Default Time Synchronization value to Disable (GNSS only)
- getops SMS command added
- Only Half ICCID sent to server on ICCID event improvement
- bt getlist improvement
- Added BLE connection control functionality, when service id is configured
- Use speed if LVCAN/OBD speed is 0
- Improved record generating when speed source is configured as OBD/CAN
- Added speed source configuration parameter for scenarios where vehicle speed is needed
- Improved speed jump filter
- Crash trace improvements
- Changed "obdinfo" sms response - returns LAST detected OBD protocol now
|
| 03.18.21.Rev.00 |
2019.02.28 |
- Improved OBD data reading
- Changed "obdinfo" sms response
|
| 03.18.20.Rev.00 |
2019.02.21 |
- Improved Ultra Deep sleep mode
|
| 03.18.19.Rev.00 |
2019.01.14 |
- Improved FMB207 support
- Improved simultaneous DNS requests issue (DNS fails if requesting at same time). Do not affects FM3/FM4 with ext modem
- Improved path creating for NMEA logging file (after sdformat)
- OBD & ELD improvements
- 1-Wire Dallas temperature sensors improvements
- Do not allow unauthorized incoming calls if any authorized number is configured
- VIN reset/change on ELD improved
- Changed default battery level sms text to "Battery level %"
- Improved CODEC12 CMD server -> RS232/RS485 data length
- CAN interrupt handling reworked
- Improvement for putting space to APN configuration then it's empty and sim is inserted
- Improved DOUT control over SMS when no DOUTs are enabled
- Reworked external modem power off/on procedures
- Changed SMS cmd "getgps" time source, to prevent zero values when GPS is OFF
- GSM numbers handling rework
- Improvement for Bluetooth communication over BT 3.0
|
| 03.18.16.Rev.00 |
2018.12.04 |
- Changed default configuration parameters values
- Improved SIM switch algorithm for DUAL-SIM devices (FMB125, FMB122)
- Added possibility to set LV-CAN200, ALL-CAN300, CAN-CONTROL program number using SMS command in Online Deep Sleep mode
- Improved RS485 LLS reconfiguring on different positions
|
| 03.18.15.Rev.00 |
2018.11.26 |
- The conditions for entering sleep depend on this parameter:
Always / After Time Sync / After Position Fix
- Improved records reading and sending
- Fixed Total Odometer IO values appearing in Trip Odometer IO
- Fixed unexpected GPS LED blinking after wake up from sleep
- UDP data sending improvements
- Fixed CAN CONTROL speed I/O element value parsing
- Fixed Battery Voltage I/O coefficients
- Improved Crash Detection duration calculation
- Changed odometer configuration parameter available min value to 0, while on TCP configuration values is from 1
- Improved auto calibration algorithm
- Improved data sending algorithm
- Removed forced record sending after waking up from deep sleep
- Fixed ELD data sending via BLE
- ELD speed source selection improvements
- Fixed BLE temperature sensors I/O low level configuration
- Changed odometer source switching algorithm (OBD<->GNSS). If OBD data becomes unavailable device will not switch to GNSS source automatically
- Improved crash data packing
- Fixed SMS "odoset:" max value validation
- Fixed device restarts due too many BLE devices in range when performing scanning operation
- Improved LLS data reading stability
- Changed "Engine Oil Temperature" OBD IO element value representation from SIGNED to UNSIGNED
- Increased Odometer max value from 999999 to 4294967
|
| 03.18.03.Rev.00 |
2018.09.25 |
- Fixed AIN1 and External Voltage swap for FMB900
|
| 03.18.02.Rev.00 |
2018.09.24 |
- Added shadow calibration functionality
- Improved eco driving events functionality
- Improved GNSS hdop&pdop validation
- Fixed LVCAN Fuel Level value coefficient according to IO protocol
- Added Battery level % IO element
- Fixed gps fix acquisition
- Added Configurable BLE transmitting power
- Added ELD support into base OBD FW version
- Improved communication with FOTA WEB
- Reworked IO manager to properly support variable length of IO
- Improved operation in Deep Sleep
- Improved records packing
- Improved crash records generation.
- Improved FW startup speed
- Increased Trip status reading from BTAPP rate
- Improved Idling functionality
- Fixed duplicated record issue
- Improved Bluetooth scanning functionality
- Added OBD DTC, LVCAN DTC IO elements
- Improved Power consumption in sleep mode
- Fixed incomming call detection
- Improved records saving scenario
- Added MIN SPEED protections for ECO DRIVING
- Improved RS232 operation after device initialization
- Improved TZBT data reading
- Improved eco/green driving and crash detection functionalities
- Max packet size increased from 1024 bytes to 1280 bytes
|
| 03.10.09.Rev.00 |
2018.07.03 |
- Improved LiPo battery detection
|
| 03.10.08.Rev.00 |
2018.06.25 |
- Fixed FOTA WEB hardware detection
- Improved SMS/GPRS command "setdigout" with speed parameter according to documentation (do not trigger DOUTx if GNSS FIX unavailable)
- Added ELD VIN number validation
- Fixed OBD and LVCAN IO current value showing in configurator
- Fixed record sending if mode was changed and send period “0”
- Added FMB125 BLE DualSIM HW support
|
| 03.10.03.Rev.00 |
2018.05.31 |
- Added TZ-BT05B sensor support
- Improved BLE scanning
- Improved data sending scenario
- Fixed configuration loading after download via FOTAWEB issue
- Improved DOUT functionality
- Added CAN-CONTROL support
- Changed LVCAN Engine Temperature and LVCAN Fuel Level value coefficient (according IO protocol)
- Added new SMS/GPRS command "getimsi" for IMSI number reading
- Added ELD functionality
- DNS support improvement
- Stability improvements
|
| 03.09.01.Rev.00 |
2018.04.30 |
- Improved FOTA WEB functionality
- Improved odometer value calculating from LVCAN (km->m)
- Improved 1-wire operation with long wires
- Improved Bluetooth functionality
- Improved OBD data reading
|
| 03.08.05.Rev.00 |
2018.04.18 |
- Improved Static Navigation filter
- Improved Crash Detection scenario
- Improved device connection to configurator after FW update
- Updated LVCAN protocol to support 4 and 5 digits numbers
- BT functionality optimization
|
| 03.07.07.Rev.00 |
2018.04.05 |
- Improved simultaneous use of several Bluetooth connections
|
| 03.07.06.Rev.00 |
2018.03.19 |
- Fixed IO elements High/Low config parameters negative values saving
- Improved OBD communication
- Improved Outgoing Call trigger conditions
- Improved VIN reading
- Record saving optimization
- Improved iButton expire time calculation
|
| 03.07.01.Rev.00 |
2018.03.02 |
- OBD pinout for FM3 improvement
- Improved data sending
- Improved FOTA WEB configuration sending
- Changed GPS state values reporting in SMS "getinfo" according documentation
- Improved Crash Detection
- Added GPRS OPEN timeout for FOTA WEB
- Improved UNLOCK key generation for keyword restoring
- LiPo battery charging optimization
- Added FMB2YX hardware support
|
| 03.06.04.Rev.00 |
2018.02.12 |
- Improved record storing and sending algorithm
- Improved communication with accelerometer
- Improved firmware update handling with internal flash memory
|
| 03.06.01.Rev.00 |
2018.01.29 |
- BLE functionality added
- Improved OBD request functionality
- Improved record search and sending scenario
- Fixed SD storage (used/total) info displaying
- Added OBD stuck protection
- Improved logging
- Improved movement detection in sleep modes
- Added SMS "getrecord" for High prio record generation
- Added fix for GPRS authentication pap/chap
- Added Ultra Deep Sleep functionality
- Improved LiPo charging algorithm
- Added support of FM30XY hardware
|
| 03.03.07.Rev.00 |
2018.01.03 |
- New parameter for SMS event compositor: %gmap – provides Google Maps link in SMS event message
- Improvement for OBD data display in Configurator Status window
- Improved Ignition and Movement detection by CAN data (OBD/LVCAN)
- Improved iButton IO event generation after sleep mode
- Fixed Trip odometer precision when counting mode is “Between records”
- Fixed “setdigout” command usage on FMB9YX
|
| 03.03.06.Rev.00 |
2018.01.03 |
|
| 03.03.03.Rev.00 |
2017.12.05 |
- Added iButton ID inversion to solve incompatibility with FMA
- Added additional iButton family ID’s
- Improved backup server triggering if main server DNS request fails
- Removed Ios generation in deep/online sleep for EcoScore, Dallas Temp/ID, iButton, RFID, LLS
- Enabled GSM I/O’s in online sleep
- Added setdigout dependency on speed. DOUT change is not executed while speed is too high.
- GPS version string truncated in “getver” SMS response
- Movement detection sensitivity decreased
- Improvement in records manager to prevent records corruption
- High priority events are not checking to send period now
- Towing IO reset on feature reactivation added
- Fixed FOTA WEB issue when APN has login and password
- Major stability improvement patch!
- Added immobilizer state restore on startup
- SMS sending is now aborted after 3 unsuccessful attempts
- SMS events text composition added. You can add additional parameters to SMS text
- Improved HID RFID reading in FMB125
- Added Green Driving Duration IO element (AVL ID: 243)
- Fixed SIM PIN change via Bluetooth
- RS232 buffered modes added
|
| 03.02.03.Rev.00 |
2017.10.17 |
- Updated GPS FW (Galileo satellites are used now too)
- Auto calibration procedure improved
- Added new LV-CAN200 parameters: CNG Status, CNG Used, CNG Level, OIL Level, Engine Temperature
- Added “getimeiccid” SMS/GPRS command
- IMEI packaging for UDP fixed
- Crash Trace fixed
- BTAPP application improvement
- OBD PID data requesting when VIN unavailable fixed
- Fake overspeeding events are now filtered out
- Fixed BT name autogenerating if empty
- Fixed records sending via UDP
- Autoconnect to FotaWeb on power ON and after “cpureset“ added
- OBD protocol detection improvements
- GNSS (used for records) data while device is in GPS sleep / deep sleep / online deep sleep fixed
- Changed BT DEFAULT name autogeneration by device type
- Improved SD present and mounted state detection
- Removed check for AIN min value 500mV
- Records sending by min saved records fix
|
| 03.01.04.Rev.00 |
2017.09.06 |
- New feature: NMEA via Bluetooth
- New feature: Read records
- New feature: iButton reading notification via DOUT.
- New SMS/GPRS command: getvin (Returns vehicle VIN number. Aplicable for FMB001, or other FMB devices with connected OBDII dongle)
- BTAPP protocol updated
- Improvements in records sending (fixes increased traffic usage)
- Improved configuration saving time
|
| 01.03.13.Rev.00 |
2017.11.07 |
- Improved overall device stability
- Fixed Bluetooth Data Link.
- Fixed Bluetooth name auto-generating if empty.
- Fixed Bluetooth clear all Paired device list from configurator.
- Fixed records sending via UDP.
- Fixed IMEI packaging for UDP.
- Improved SMS login/pass validator. All characters are now allowed.
- Added protection for OBD Odometer value reset.
- Added protection for IMEI corruption.
- Fixed bad records detector.
- Added call functionality (when event detected) in Deep Sleep mode.
- Restart protection fixed.
- Improvements in SIM PIN setting.
- Changed default FOTA WEB Domain.
- Fixed OBD PID data requesting when VIN unavailable.
- OBD protocol detection improvements.
- Modem power ON improvements.
- NTP improvements.
- Added “getimeiccid” SMS/GPRS command.
- SMS/GPRS command “sdformat” improvements.
- SMS Login/Pass validator improvements.
- Removed check for AIN min value 500mV.
- Added additional IO High/Low-level setter by ParamID.
- Fixed SMS processing state check in modem SLEEP mode setter.
- FOTA functionality improvement.
- Added protections by GSM number and text length.
- IO event External Voltage DeltaChange improvements.
- Fixed issues with double records, bad records, record search.
- Fixed microSD to RAM switching for records saving.
- Added retries for unsuccessful outgoing call.
|
| 01.03.11.Rev.00 |
2017.10.19 |
- Fixed Crash detection functionality.
- Battery charging improvement.
- Record sending via UDP fixed.
- Record sending in DeepSleep improvement.
- FOTA WEB functionality improvement.
- Added protection for IMEI corruption.
|
| 01.03.03.Rev.00 |
2017.07.24 |
- Added FOTA WEB functionality
- Optimization of power consumption in sleep modes
- GNSSS IO Text "GNSSpower" changed to "GNSSStatus"
- Added zero filling the ibutton values
- Enabled IOs GNSS, Total Odometer in dsleep mode
- Improved getio SMS response for FMB125
- Added CCID validity check before PIN registration
- Minimized power consumptions in sleep modes
- Added SD card check before it’s usage
- Changed excessive idling default/max values
- DUAL SIM functionality implementation
- PIN Entering to second SIM improvement
- SMS/GPRS getgps command improvement
- Added dual server support
- Operator Black list implementation
|
| 01.00.32.Rev.00 |
2017.07.10 |
- Authorized GSM numbers list increased to 200
- Unplug feature improvement
- SMS command 'sdformat' – deletes all internal memory
- SMS command ‘deleterecords’ – deletes Avl records from memory
- Faster GPS FIX after leaving sleep mode
- ‘odoset’ SMS command fixed
- Excessive Idling functionality improvement
- DOUT state is restored on startup
- Towing activation timeout max value increased
- Averaging now works in Deep Sleep mode too
- Minor OBD improvements
- Bluetooth pairing improvements
- FMB962/FMB964 hardware support added
- Records sending when link is open fixed
|
| 01.00.30.Rev.05 |
2017.05.26 |
- Added 5 geozones functionality
- IO elements ICCID and SD Status are added
- Added Keyword functionality
- Crash detection improvement, now it detects consecutive events
- Towing Detection improvement
- Unplug detection improvement
- GPRS connection stability improvement
- Improved Unplug detection – now detects “plug” events too
- Data sending without microSD card
- getgps SMS commands format fixed
- Default configuration changed – allow sending in roaming and unknown modes
|
| 01.00.22.Rev.12 |
2017.04.13 |
- Improved connection to GSM operators
|
| 01.00.22.Rev.11 |
2017.04.07 |
- Improved LiPo battery charger state interpretation
|
| 01.00.22.Rev.09 |
2017.03.28 |
- Updated GPS firmware version
- Hardware detection improvement
|
| 01.00.22.Rev.06 |
2017.03.14 |
- Corrected “Green driving” values: “m/s2” conversion to “g”
- SIM PIN entering fixed.
- SMS Reading improved. Don't go to DeepSleep if there are SMS to read in memory.
- GPS Fuel Counter fix.
- Jamming detection improvement.
- AutoGeofence functionality improvement.
|
