Difference between revisions of "Inateck BCST-70 Configuration"
From Wiki Knowledge Base | Teltonika GPS
m (Text replacement - "Bluetooth(?!®)" to "Bluetooth®") Tags: Mobile edit Mobile web edit |
m (Protected "Inateck BCST-70 Configuration" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))) |
||
| Line 6: | Line 6: | ||
#In System settings, enable Codec8 Extended</br></br>[[File:Data_Protocol.png|border|250px]]</br></br> | #In System settings, enable Codec8 Extended</br></br>[[File:Data_Protocol.png|border|250px]]</br></br> | ||
#In GPRS settings, configure GPRS Settings and Server Settings.</br></br> | #In GPRS settings, configure GPRS Settings and Server Settings.</br></br> | ||
| − | #In | + | #In Bluetooth settings, |
| − | ::*Enable | + | ::*Enable Bluetooth, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth will be disabled |
| − | ::*Under | + | ::*Under Bluetooth Control, click Discover so it would detect devices within vicinity. </br></br>[[File:Bluetooth_Control.png|border|200px]]</br></br> |
::*Once devices are discovered, select BCST-70-XXXX-SPP then proceed to tick Pair | ::*Once devices are discovered, select BCST-70-XXXX-SPP then proceed to tick Pair | ||
::*After successful pairing, scanner should show under Paired Devices. </br></br>[[File:Paired_Devices.png|border|200px]]</br></br> | ::*After successful pairing, scanner should show under Paired Devices. </br></br>[[File:Paired_Devices.png|border|200px]]</br></br> | ||
| − | <span style="color:#FF0000">'''NOTE:'''</span> : '' If in case the Scanner is not discovered, do the following steps on | + | <span style="color:#FF0000">'''NOTE:'''</span> : '' If in case the Scanner is not discovered, do the following steps on Bluetooth Pairing.'' |
| − | ==Enable | + | ==Enable Bluetooth Pairing== |
<ol style="list-style-type:lower-alpha"> | <ol style="list-style-type:lower-alpha"> | ||
<li>Scan “Enter Setup” </br></br>[[File:Enter_Setup.png|325px]]</br></br></li> | <li>Scan “Enter Setup” </br></br>[[File:Enter_Setup.png|325px]]</br></br></li> | ||
| − | <li>Scan “ | + | <li>Scan “ Bluetooth Pairing” </br></br>[[File:Bluetooth_Pairing.png|325px]]</br></br></li> |
<li>Scan the "Exit with Save" barcode </br></br>[[File:Exit_Save.png|325px]]</br></br></li> | <li>Scan the "Exit with Save" barcode </br></br>[[File:Exit_Save.png|325px]]</br></br></li> | ||
</ol> | </ol> | ||
Revision as of 10:33, 2 May 2023
Main Page > Accessories > Inateck BCST-70 Barcode Scanner > Inateck BCST-70 ConfigurationConfigure FM device using Teltonika configurator
- In System settings, enable Codec8 Extended
- In GPRS settings, configure GPRS Settings and Server Settings.
- In Bluetooth settings,
- Enable Bluetooth, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth will be disabled
- Under Bluetooth Control, click Discover so it would detect devices within vicinity.
- Once devices are discovered, select BCST-70-XXXX-SPP then proceed to tick Pair
- After successful pairing, scanner should show under Paired Devices.
NOTE: : If in case the Scanner is not discovered, do the following steps on Bluetooth Pairing.
Enable Bluetooth Pairing
- Scan “Enter Setup”
- Scan “ Bluetooth Pairing”
- Scan the "Exit with Save" barcode
Scanner Auto Connect Configuration
- Fill up the “Auto Connect To External Device“ with as follows:
- Select Connection Mode as, Inateck Scanner.
- Enter the External MAC, can be seen on Paired Devices at the upper left corner.
- Enter the External Name, can be seen on Paired Devices at the lower right corner.
- Enter the External Pin, if the scanner has pin code set otherwise leave as blank.
- Fill up the “Authorized Devices MAC List“ same with the External MAC.
NOTE: : It is important to fill out the auto connect so you won‘t need to Pair the device again on the Configurator.
- To receive the data to server enable corresponding BT Status IO element to Low.
NOTE: : If Scanner is connected BT Status value would be read as 2
